Headphones 7000 Series TAA7306 User manual Register your product and get support at www.philips.
Contents 1 Important safety instructions 2 Hearing Safety General information 2 2 2 Your Bluetooth wireless earpieces What's in the box Other devices Overview of your Bluetooth wireless earpieces 3 Get started Charge the battery Pair the earpieces with your Bluetooth device at the first time Pair the earpieces with another Bluetooth device 4 Use your headphones 3 3 3 4 5 5 6 6 7 Connect the earpieces to your Bluetooth device 7 Power on/off 7 Manage your calls and music 7 Battery LED indicator on
1 Important safety instructions Hearing Safety Danger To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guidelines when using your earpieces. • Listen at reasonable volumes for reasonable periods of time. • Be careful not to adjust the volume continuously upwards as your hearing adapts.
2 Your Bluetooth wireless earpieces Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/support. With this Philips wireless headphones, you can: • enjoy convenient wireless handsfree calls; • enjoy and control wireless music; • switch between calls and music.
Overview of your Bluetooth wireless earpieces 4 6 7 8 1 Microphone 2 LED indicator (Earbud) 3 Touch panel 4 Heart rate monitor (HRM) sensor 5 Operation LED (Charging case) 6 LED indicator ( charging case ) 7 USB-C charging slot 8 Reset button (Right side only)
3 Get started • • Charging process is verified by white LED light on the earpiecess. When the earpieces is fully charged, the white light goes off. Charge the battery Note Before you use your earpieces for the first time, place the earpiecess in the charging case and charge the battery for 3 hours for optimum battery capacity and lifetime. Use only the original USB charging cable to avoid any damage.
The earpiecess are now in pairing mode and is ready to pair with a Bluetooth device (e.g. a mobile phone) Turn on the Bluetooth function of your Bluetooth device. UV sterilization function Put the earpieces into charging case and close the lid, the UV sterilization LED will turn on for 1 minute. Pair the earpiecess with your Bluetooth device. Refer to the user manual of your Bluetooth device.
4 Use your Headphones Connect the earpieces to your Bluetooth device Power on/off Task Turn the earpieces on. Take out earpiece from charging box to power on Turn the earpieces off. Put back earpiece to charging box to power off Turn on the Bluetooth function of your Bluetooth device. Open the top cover from charging box. The blue LED flashes. The earpieces will search the last connected Bluetooth device and reconnect to it automatically.
Operation Touch panel Three Way Calling Right/Left Single tap Hold current call earpiece and accept an incoming call Task Three Way Calling Hold current call and reject an incoming call Three Way Calling Cancle current call and accept an incoming call Right/Left Press & earpiece holding 2 sec Right/Left Double taps earpiece Three Way Calling Right/Left Triple taps Hold current call earpiece and switch before call Voice control LED indicator status Earpieces status The earpieces is connected to a Bluet
Heart rate monitor Task Touch panel Operation Heart rate monitor on / off Left earpiece Double taps Broadcast heart rate Left earpiece Single tap 5 Factory reset the earpieces Philips headphones APP Current heart rate Highest heart rate Lowest heart rate Average heart rate Note The HRM function supports Philips Headphone APP.
6 Technical data Earpieces Music time: 6 hours (additional 18 hrs with charging case) Talk time: 6 hours (additional 18 hrs with charging case) Standby time: 200 hours Charging time: 2 hours Rechargeable lithium ion battery: 105 mAh on each earpieces Bluetooth version: 5.0 Compatible Bluetooth profiles: • HSP (Hands-Free Profile-HFP) • A2DP (Advanced Audio Distribution Profile) • AVRCP (Audio Video Remote Control Profile) Supported audio codec: SBC, AAC Frequency range: 2.402 -2.
7 Notice negative consequences for the environment and human health. Declaration of conformity Remove the integrated battery Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can find the Declaration of Conformity on www.p4c.philips.com.
Compliance with EMF This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields. Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
9 Frequently asked questions My Bluetooth earpieces does not turn on. The battery level is low. Charge the earpieces. I cannot pair my Bluetooth earpieces with my Bluetooth device. The Bluetooth is disabled. Enable the Bluetooth feature on your Bluetooth device and turn on the Bluetooth device before you turn on the earpieces. Pairing does not work. • Put both earpiecess into charging case. • Make sure you have disabled the Bluetooth function of any previously connected Bluetooth devices.
I hear but cannot control music on my Bluetooth device (e.g. play/pause/skip forward/backward). Make sure the Bluetooth audio source supports AVRCP (see ‘Technical data’ on page 10). The volume level of the earpieces is toot low. Some Bluetooth devices cannot link the volume level with the earpieces through volume sync. In this case, you have to adjust the volume on your Bluetooth device independently to achieve an appropriate volume level.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product. UM_TAA7306_27_EN_v1.
