Register your product and get support at www.philips.
1 2 3 4 Important 4 4 Your Wireless HD AV Connect 6 6 Overview The transmitter The receiver The remote control 7 7 7 8 Installation 9 Safety What is in the box Connect the transmitter to your HD devices 9 Connect the receiver to the HDTV set 9 Connect the IR blaster and IR sensor extender cables 10 Install remote control batteries 10 5 Activate your Wireless HD AV Connect and set up the link Turn on the power of your HDTV Activate the wireless li
1 Important e Do not use this apparatus near water. Safety g Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. f Clean only with dry cloth. h Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. This ‘bolt of lightning’ indicates uninsulated material within your unit may cause an electrical shock.
English n Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
2 Your Wireless HD AV Connect Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips. com/welcome. HDMI cable IR blaster extender cable What is in the box Note •• Make sure you have all these items in the box. Contact your dealer for any missing or damaged items.
The receiver English 3 Overview Top view The transmitter Front view 1 1 2 3 Source LEDs It displays the current source input. SOURCE Press to switch the button source input of the transmitter. Power button Press to turn the with the LED transmitter on/off indicator 2 3 Source LEDs Indicators for HDMI1 and HDMI2 Press to turn the receiver Power button with on/off. the LED indicator Source Press to select the button source input.
The remote control POWER Press to turn the button transmitter and receiver on/off. INFO Displays on the HDTV button the connection status of the receiver. IR Press to switch the IR button blaster frequency to meet the requirement of the source device. SOURCE Press to switch the button audio/video source inputs connected to the transmitter. 1 2 3 4 The Wireless HD AV Connect gives you a total wireless solution to place your HDTV set or projector anywhere you want.
2 Connect the supplied power adapter to the transmitter. • Connect one end of the power adapter to the DC IN jack of the transmitter. • Connect the other end of the power adapter to a power outlet. »» The power button of the transmitter is lit in solid blue and turns red in standby mode. Connect the transmitter to your HD devices You can connect two audio/video sources to the transmitter at the same time, but only one source can be selected and played.
Connect the IR blaster and IR sensor extender cables 5 Extend and stick the IR sensor extender cable onto the front side of your HDTV. Note Tip •• If you cannot use the remote control of your device, •• The IR blaster support 47KHz remote signal protocol, while the IR sensor supports 36KHz - 56KHz (NEC, RC5, RC6) remote signal protocol. follow the steps in this section to connect the sensor extender cables .
Turn on the power of your HDTV HDMI OUT IR IN DC 5V HDM I On screen display on HDTV On screen display English 5 Activate your Wireless HD AV Connect and set up the link Mode and status Standby mode: it is a powersaving mode ..... Start up in progress: It takes 1520 seconds. x and .... Searching available channels: It occurs when the link cannot establish over 80 seconds after initialization.
Activate the wireless link Switch on the transmitter and receiver In standby mode, a red power LED displays on the transmitter and receiver.You can then turn on the transmitter and receiver in the following ways: Select the source on the transmitter Press the source buttons on the remote control, transmitter or receiver until you see the available video from your device. Tip •• For information on the LED indicator status, see the section on ‘LED indicator status of the transmitter’.
5 Hook the key holes at the back of the receiver on the screws. English 6 Mount your receiver You can either mount the receiver on the wall or on the back of the HDTV. Mount your receiver on the wall 1 2 3 4 Select a spot near the HDTV. Drill two holes in the wall. Make sure that the distance between the two holes is 1 25/32” (45 mm) and the diameter of the hole is 3/16” (5 mm). Punch the supplied two anchors into the two holes on the wall.
Mount your receiver on the back of the HDTV 1 2 Remove the white protective film from one of the supplied adhesive tapes. Secure the glued side of the adhesive tape and attach it to the central bottom area of the receiver. 6 Align the adhesive tape on the receiver with the one on the HDTV until both the receiver and HDTV are mounted together firmly. Note •• The use of adhesive tapes is an alternative mounting option when the receiver cannot be fixed.
Supported resolution Power supply: Input: AC 100~ 240V Output: DC 5V, 2A Operating temperature: 0~40°C/32~104°F Video format timings Resolution Transmitter interfaces Primary CEA video timing 480p 480p 480p 576p 720p 720p 1080i 1080i 1080p/60 1080p/60 - A/V interfaces HDMI input: Two (Type A) Control signal interfaces IR blaster extender: 2.
8 Notice Notice for USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. Never dispose of your product with other household waste. Please inform yourself about the local rules on the separate collection of electrical and electronic products. The correct disposal of your old product helps prevent potentially negative consequences on the environment and human health. The packaging of this product is intended to be recycled.
9 Frequently asked question The power LED on the receiver is not lit up in red in standby mode. The computer screen image is not full screen on my TV. •• 1 2 3 4 5 6 There is no video displayed on •• my TV screen. •• •• 18 EN Make sure that there is power supply for the transmitter and receiver. Right-click on an open space on your desktop. Select Graphics Options > Output to > Digital Television (Now the laptop image will only appear on your TV).
•• •• Make sure that the video resolution of your source device matches the resolution of your HDTV. Make sure that the transmission range between receiver and transmitter is not over 65 feet (19.7 meters) transmission distance. English If the picture quality is poor, what do I do? Tip •• For information, see the chapter on ‘Technical data’. I cannot hear any sound or the •• sound is poor, what do I do? •• •• •• Make sure that the TV volume is adjusted correctly.
EN
© 2011 Koninklijke Philips Electronics N.V. All rights reserved. IFU_SWW1810_EN_V2.
