Register your product and get support at www.philips.
Philips Consumer Lifestyle HK-0948-MCi500H-FR 2008 ........................................................ (Report No. / Numéro du Rapport) ........................................................................... (Year in which the CE mark is affixed / Année au cours de laquelle le marquage CE a été apposé) EC DECLARATION OF CONFORMITY (DECLARATION DE CONFORMITE CE) We / Nous, PHILIPS CONSUMER LIFESTYLE B.V.
1 Important Safety Environmental notices Disposal of product & packing material 2 Your Wireless Micro Hi-Fi System Overview Front view Back view Remote control 3 Prepare Position Wireless Micro Hi-Fi System Connect to AC power Turn on / switch to standby First-time installation Select language 4 Connect to a home network Create wireless connection with automatic IP address Create wireless connection with static IP ad
Time settings 26 Synchronize with RDS radio station 26 Set the time format 26 Set the time manually 26 Set standby timer 26 Change recording speed 26 Change recording quality 27 Change language 27 Maintenance 27 Cleaning 27 Update 27 Update through PC connection 27 Restore the default settings 28 12 Add a Philips Wireless Music Station (sold separately) Add a Philips Wireless Music Station to Wireless Micro Hi-Fi System Broadcast
i Only use this product indoors. Do not expose the product to dripping / splashing water, rain or high humidity. English 1 Important Safety j Keep this product away from direct sunlight, naked flames or heat. Information for Europe: Know these safety symbols k Do not install near any heat sources such as radiators, heat registers, stoves, or other electrical equipment (including amplifiers). l Do not place any other electrical equipment on the product.
set your volume to a safe level before your hearing adapts and leave it there. To establish a safe volume level: Set your volume control at a low setting. Slowly increase the sound until you can hear it comfortably and clearly, without distortion. Listen for reasonable periods of time: Prolonged exposure to sound, even at normally ‘safe’ levels, can also cause hearing loss. Be sure to use your equipment reasonably and take appropriate breaks.
English Information about the use of batteries: Caution •• Risk of leakage: Only use the specified type of batteries. Do not mix new and used batteries. Do not mix different brands of batteries. Observe correct polarity. Remove batteries from products that are not in use for a longer period of time. Store batteries in a dry place. •• Risk of injury: Wear gloves when handling leaking batteries. Keep batteries out of reach of children and pets. •• Risk of explosion: Do not short circuit batteries.
2 Your Wireless Micro Hi-Fi System Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips. com/welcome.
l SHUFFLE m INCR.SURR.
3 Prepare Connect to AC power Warning Caution •• Risk of product damage! Ensure that the power supply voltage corresponds to the voltage printed on the type plate (at the back or at the underside of Wireless Micro Hi-Fi System). •• Risk of explosion! Keep batteries away from heat, sunshine or fire. Never discard batteries in fire. •• Risk of decreased battery life! Never mix different brands or types of batteries.
2 3 To turn on Wireless Micro Hi-Fi System, press . English 1 To switch Wireless Micro Hi-Fi System to standby, press . To switch Wireless Micro Hi-Fi System to eco standby, press and hold the button on the top panel. Note •• When Wireless Micro Hi-Fi System is in eco standby mode, the remote control is inactive. In eco standby mode, the Wireless Micro Hi-Fi System still consumes a small amount of power.
4 Connect to a home network 1 Before you connect Wireless Micro Hi-Fi System to a router: • Ensure that the PC meets the minimum requirements.
• 1 2 3 4 5 6 7 8 9 To cycle through the alphanumeric characters that are available, press a button repeatedly. To delete the last character entry from the display, press CLEAR. This chapter shows you how to create a wireless connection to a home network with static IP address. Ensure that your encryption key (if required) is available. • • • Turn on your wireless access point or wireless router with broadband Internet. Turn on Wireless Micro Hi-Fi System. On Wireless Micro Hi-Fi System, press MENU.
• • 1 2 3 4 5 6 7 12 until you see the number or alphabetic character in the display of Wireless Micro Hi-Fi System. To cycle through the alphanumeric characters that are available, press a button repeatedly. To delete the last character entry from the display, press CLEAR. This chapter shows you how to create a wired connection to a home network with automatic IP address.
You have the following options to build a music library on the harddisk: • rip music from CDs • import music from a PC • record music from FM radio • record music from an external device Music recognition technology and related data are provided by Gracenote®. Gracenote is the industry standard in music recognition technology and related content delivery. For more information, please visit www.gracenote. com. CD and music-related data from Gracenote, Inc., copyright © 2000-2007 Gracenote.
3 4 5 6 Press MARK/UNMARK to select/ deselect tracks. (By default, Wireless Micro Hi-Fi System rips all tracks of the CD when no tracks are marked.) • Long press MARK/UNMARK to select/deselect all tracks. Press REC to start ripping. To rip another CD, repeat above steps 1 to 4. To stop ripping, press . Tip •• For information about how to change the rip quality, see chapter Settings. Record music You can record from 2 different sources. 1 2 3 14 Press • AUX to record from an external device.
Mark Internet radio stations as Favorites Play CD You can mark Internet radio stations as your Favourites so next time you want to listen to a station, it is easy to find. 1 2 3 4 Press to open the CD tray. Insert CD with printed side facing up. Press to close the CD tray. Press OK / to play. 1 2 3 Internet radio Note •• Internet radio features require broadband Internet access. Ensure that Wireless Micro Hi-Fi System is connected to broadband Internet.
Note •• Internet radio features require broadband Internet access. •• You can also organize your Favorites under Streamium Management on the Philips website. Manually add Internet radio stations This chapter explains how to register with Philips and add individual URL addresses for Internet radio stations on the PC. 1 2 3 4 5 6 7 8 Turn on Wireless Micro Hi-Fi System. Ensure that Wireless Micro Hi-Fi System is connected to broadband Internet.
1 2 3 4 Ensure that Wireless Micro Hi-Fi System is turned on. Ensure that you fully extend the connected FM antenna. 3 4 Press HOME. Press FM TUNER. »» The current frequency is displayed. »» To return to the Home menu, press HOME. 5 6 7 Tip rotate the FM antenna. •• You can use the automatic search & store function to store channels under presets. To fine tune the reception of a channel, you can adjust the channel frequency. 1 2 3 4 Ensure that Wireless Micro Hi-Fi System is turned on. Press HOME.
3 4 5 Press or , then to select [FM Tuner]. »» The current frequency is displayed. Press to display preset channel numbers. Press to select, then press . • To return to the Home menu, press HOME. Manual search & store You can manually search and store channels. 1 2 3 4 5 6 7 Turn on Wireless Micro Hi-Fi System. Press HOME. Press or , then to select [FM Tuner]. »» The current frequency is displayed. Press to change the frequency. Press MENU.
Press / to select the server name and confirm with OK. Tip •• The TwonkyMedia™ sharing page lets you set the rescan behavior of the server. The default setting is -1 minutes, which ensures auto-scan. Play from a flash memory USB device Connect audio devices (AUX) You can play music from an external appliance that is connected to the AUX input of Wireless Micro Hi-Fi System.
7 Play options You can choose between various play options: • Repeat play • Shuffle play • Play by artist • Play by genre Repeat play You can repeat one or all audio files of the current selection. 1 In play mode, press REPEAT to toggle the repeat function as follows: • Repeat 1 • The current audio file is continuously repeated until another mode or setting is selected. • Repeat all • All audio files of the current selection are continuously repeated until another mode or setting is selected.
English Add audio files to a playlist You can add up to 300 audio files to a playlist. 1 2 3 4 5 6 Ensure that Wireless Micro Hi-Fi System is turned on. On the remote control, press HD. Press or , then to select audio file. Press MENU to enter the HD menu. Press or , then Playlist]. to select [Add To Press or , then to select playlist. »» The audio file is added to the selected playlist. »» To return to the Home menu, press HOME.
8 Record from HD to USB You can record music files from the HD (harddisk) of Wireless Micro Hi-Fi System to a flash memory USB device. 1 2 3 4 5 6 22 Insert the USB plug of the USB device into the USB socket of Wireless Micro Hi-Fi System: Use the remote control of Wireless Micro Hi-Fi System for the following steps: Press HD. Press REC . Press MARK/UNMARK to select/ deselect tracks. (By default Wireless Micro Hi-Fi System records all tracks of the HD when no tracks are marked.
English 9 Alphanumeric search You can search for specific audio files on a connected UPnP device. 1 2 3 4 5 6 7 8 Ensure that Wireless Micro Hi-Fi System is turned on. Press HOME. Press or , then to select the music source. »» The display shows the available lists. Press or , then to select list. Press SEARCH. »» The display shows a text box. Press the alphanumeric buttons on the remote control to enter the search word. Press OK / to start the search.
10 Gracenote® CD information Gracenote® CD Information Gracenote MusicID® provides the set with CD track information (including album, artist, genre, track information) from its built-in database. It allows the recorded CD tracks to be properly categorized (for example, under Artists, Albums, Genres or All tracks) and be merged with the existing tracks in the hard disk. Gracenote® Media Database A CD database is embedded in every MCi500H for quick look-up on track information.
• Adjust volume • 1 During play, press + VOL - to adjust the volume. Mute You can turn off the sound of your audio. 1 During play, press MUTE. • To turn the sound back on, press MUTE again. Change Equalizer (EQ) settings You can adjust the audio sound with the following equalizer settings: • [Rock] • [Pop] • [Jazz] • [Neutral] • [Techno] • [Classical] 1 2 3 4 Turn on Wireless Micro Hi-Fi System. Press MENU. Press or , then [Equalizer]. to select Press or to select.
Time settings Set the time manually This chapter shows you how to change the time settings. Synchronize with RDS radio station RDS (Radio Data System) is a service that allows FM stations to send additional information along with the FM radio signal. Automatic time synchronization is one of the RDS features. 1 2 3 4 5 6 2 3 4 5 2 3 4 5 Ensure that the radio station you select for synchronization has RDS. Ensure that Wireless Micro Hi-Fi System is turned on.
Maintenance You can change the speed at which Wireless Micro Hi-Fi System rips a CD. Cleaning 1 2 3 4 Press CD. Note Press MENU. Press or , then to select [Settings]. Press or , then to select [Normal speed] or [Fast speed]. Change recording quality •• Avoid moisture and abrasion. 1 5 Press CD. • or , then to select [Settings]. Press or , then quality]. to select [Rec Press rate.
10 In the Device Configuration screen, select Firmware upgrade and click OK. 11 Click Browse to locate the software image file that you saved on the harddisk of the PC. 12 Click OK to start the update. »» The software update progress is shown. »» When the software installation is complete, Wireless Micro Hi-Fi System restarts. Tip •• You can also consult the user manual of the PC and manually add the WADM application to your list of programs that are safe to run.
You can add up to 5 Philips Wireless Music Stations (sold separately) and expand your wireless music to other locations in your home. 4 5 6 Add a Philips Wireless Music Station to Wireless Micro HiFi System This connection creates a wireless of the Philips Wireless Music Station to the home network that Wireless Micro Hi-Fi System connects to: 1 2 3 4 Place Wireless Micro Hi-Fi System and the Philips Wireless Music Station next to each other.
»» To stop the broadcast on the connected Philips Wireless Music Station, press . 1 Music Follows Me 2 3 Note •• This feature requires that you first connect Wireless Micro Hi-Fi System to a Philips Wireless Music Station (sold separately). As you move around at home, let the music move with you between Wireless Micro Hi-Fi System and one or more connected Philips Wireless Music Stations. The unit where the music is playing is the source unit.
Speakers General Frequency response Sensitivity Impedance Speaker drivers AC Power Dimensions (w x h x d) Weight (net) Voltage information is printed on the back or the underside of the MCi500H. 260 x 180 x 275 mm Main unit: ~ 3.5 kg Main unit + speakers: ~ 5.5 kg ECO (passive) standby 45 W < 15 W (typically 12 W)* < 0.9 W * Power consumption during active standby is based on Wi-Fi infrastructure, no LAN connection, no background music compression and no streaming to other stations.
HD player Frequency range Signal to noise ratio M4A (AAC) bit rate MP3 bit rate WMA bit rate 30 - 20,000 Hz (-3 dB) 75 dBA (IEC) 16 - 320 kbps, CBR / VBR 32 - 320 kbps, CBR / VBR up to 192 kbps, CBR / VBR 32, 44.
Caution •• Never try to repair the system yourself as this will invalidate the warranty. •• Do not open the system as there is a risk of electric shock. •• If a fault occurs, first check the FAQ points, then consult your dealer or Philips for help. Wireless Micro Hi-Fi System is connected to a home network and music skips during play (from any source including HD), what do I do? •• Ensure that the network router is turned on.
•• •• •• •• it is different from the SSID that your neighbors use for their router. Wireless Micro Hi-Fi System supports wireless and wired connection at the same time. There is a chance that your wireless IP address and your wired IP address are on the same subnet. This will confuse the device. Consider changing the DHCP range of your wireless router so that the wireless IP received by the device is on a different subnet from its wired IP address.
A AAC (Advanced Audio Coding) An audio compression scheme defined as part of the MPEG-2 standard (also known as MPEG-2 AAC or MPEG-2 NBC, or Not Backwards Compatible). It offers better sound and a compression ratio that is superior by roughly 30 percent compared to the MPEG-1 MP3 format. AC (alternating current) An alternating current is an electrical current whose magnitude and direction vary cyclically, as opposed to DC (direct current), whose direction remains constant.
Coaxial A single copper conductor, surrounded with a layer of insulation, covered by a surrounding copper shield and finally, an insulating jacket. An unbalanced transmission line with constant impedance. In audio, this type is commonly used for low level, line signals terminated in RCA connectors. Compression In audio terms, this is a process of temporarily or permanently reducing audio data for more efficient storage or transmission.
Frequency Response Is the range of frequencies that a speaker reproduces, lowest frequency to the highest. While the optimal normal is 20-20,000 Hz (Hertz), the range of human hearing for individuals is often much more restricted. A good full-range speaker system however, reproduces as much of this range as possible to cover all variations.
system with the ‘.m4a’ filename extension. M4A can produce better audio quality than MP3 using less physical space for the files. MHz (Mega Hertz) One million cycles per second. Midrange The middle three octaves (more or less) of the audio band, where the ear is most sensitive, usually between 160Hz-3kHz. Mono (monaural) The operation of an amplifier in one channel for both input and output. Can refer to an amplifier with only one channel of amplification or operating in bridged mode.
Sampling rate The precision with which a digital file describes the analog sound it represents. Basically, a lower rate produces files that sound worse and take up less drive space than those with a higher rate. CDs have a sampling rate of 44.1kHz, and DAT machines have a sampling rate of 48kHz. MiniDisc player/recorders with a built-in sampling rate converter can handle both rates. Sensitivity Volume that a speaker offers for a specific voltage input, expressed in decibels per watt (dB/W).
complex pictures get as much as they need. While this provides the best quality the final size cannot be predicted at all. Volume Volume is the most common word used to specify the control of relative loudness of sounds. It also pertains to the function on many electronic devices that is used to control the loudness. W W (wattage) A measurement of power. In speakers, wattage is a term that indicates powerhandling characteristics in dealing with electrical voltage inputs from the amplifier.
Argentina Australia Austria Belgium Belarus Brazil Bulgaria Canada Chile China Colombia Croatia Czech Republic Denmark Estonia Finland France Germany Greece Hong Kong Hungary India Ireland Israel Italy Japan Korea Latvia Luxembourg Malaysia Mexico Netherlands New Zealand (54-11) 4544-2047 1300 363 391 0810 000 205 78250145 882000110068 0800 701 02 03 (all except Sao Paulo)(11) 2121-0203 (Sao Paulo only) 8001154424 1-888-744-5477 600 744 5477 (600PHILIPS) 4008 800 008 01 800 700 7445 800222778 800142840 35
Gracenote® End User License Agreement Version 20061005 This application or device contains software from Gracenote, Inc. of Emeryville, California (“Gracenote”). The software from Gracenote (the “Gracenote Software”) enables this application to perform disc and/or file identification and obtain music-related information, including name, artist, track, and title information (“Gracenote Data”) from online servers or embedded databases (collectively, “Gracenote Servers”) and to perform other functions.
Streamium terms and conditions Terms and Conditions of Use of your Philips Streamium-enabled Device Congratulations on your purchase of a Philips Streamium-enabled Device (“Device”).These Terms and Conditions of Use give you the rights to use certain features on your Device relating to the streaming of content. You must agree to these Terms and Conditions of Use before using the Device.
or authorization is necessary, it is your responsibility to obtain any such license or authorization.You agree that you are solely liable for any damages you may incur resulting from your failure to obtain the proper license or authorization for use of the content accessible through the Device.You agree that Philips will have no liability to you with regard to your use of the content.
NOTICE SOFTWARE END USER LICENSE AGREEMENT THIS SOFTWARE END USER LICENSE AGREEMENT (“THIS AGREEMENT”) IS A LEGAL AND BINDING AGREEMENT BETWEEN YOU (EITHER AN INDIVIDUAL OR ENTITY) AND PHILIPS CONSUMER ELECTRONICS B.V. A DUTCH LIMITED LIABILITY COMPANY,WITH ITS PRINCIPAL OFFICE AT GLASLAAN 2, 5616 LW EINDHOVEN,THE NETHERLANDS AND ITS SUBSIDIARY COMPANIES (INDIVIDUALLY AND COLLECTIVELY “PHILIPS”).
security of such WM-DRM Software is compromised, Microsoft may revoke (either on its own or upon the request of the owners of Secure Content (“Secure Content Owners”)) the WM-DRM Software’s right to acquire new licenses to copy, store, transfer, display and/or play Secure Content. Revocation does not alter the WM-DRM Software’s ability to play unprotected content. A list of revoked WM-DRM Software is sent to your PC and/or your Device whenever you download a license for Secure Content.
9. Limited Software Warranty. Philips provides the Software ‘as is’ and without any warranty except that the Software will perform substantially in accordance with the documentation accompanying the Software for a period of one year after your first download, installation or use of the Software, whichever occurs first.
GPL Package / LGPL Library written offers This product contains Linux Kernel (linux-2.4.27-vrs1) Linux kernel drivers developed by NXP Semiconductors ethtool lsof modutils procps smartmontools libstdc++ libgcc busybox wireless_tools made available under the GNU GPL license version 2 (hereafter called the Program and the GNU LGPL license version 2.1 (hereafter called the Library. Philips Electronics Hong Kong Ltd.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.
b) You must cause any work that whole or in part contains or is part thereof, to be licensed as parties under the terms of this you distribute or publish, that in derived from the Program or any a whole at no charge to all third License.
special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded.
OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONS How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.
Ty Coon, President of Vice This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this License. glibc uclibc uclibc (library in dynamic link) OpenRTSP LibMMS GNU LESSER GENERAL PUBLIC LICENSE Version 2.
with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights. We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library. To protect each distributor, we want to make it very clear that there is no warranty for the free library.
The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a "work based on the library" and a "work that uses the library". The former contains code derived from the library, whereas the latter must be combined with the library in order to run. GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0.
c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.
from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code. 5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a "work that uses the Library".
Library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the user's computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with.
all its terms and conditions for copying, distributing or modifying the Library or works based on it. 10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein.
license version number, you may choose any version ever published by the Free Software Foundation. 14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this.
but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details. You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Also add information on how to contact you by electronic and paper mail.
domain by the authors. All code authors, and representatives of the companies they work for, have signed affidavits dedicating their contributions to the public domain and originals of those signed affidavits are stored in a firesafe at the main offices of Hwaci. Anyone is free to copy, modify, publish, use, compile, sell, or distribute the original SQLite code, either in source code form or as a compiled binary, for any purpose, commercial or non-commercial, and by any means.
The majority of code is written by Matt Johnston, under the license below. Portions of the client-mode work are (c) 2004 Mihnea Stoenescu, under the same license: Copyright (c) 2002-2004 Matt Johnston Portions copyright (c) 2004 Mihnea Stoenescu All rights reserved.
loginrec is written primarily by Andre Lucas, atomicio.c by Theo de Raadt. strlcat() is (c) Todd C. Miller ---Import code in keyimport.c is modified from PuTTY's import.c, licensed as follows: PuTTY is copyright 1997-2003 Simon Tatham. Portions copyright Robert de Bath, Joris van Rantwijk, Delian Delchev, Andreas Schultz, Jeroen Massar, Wez Furlong, Nicolas Barry, Justin Bradford, and CORE SDI S.A.
furnished to do so, subject to the following conditions: The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
# along with this program; if not, write to the Free Software # Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. # # As a special exception to the GNU General Public License, if you # distribute this file as part of a program that contains a # configuration script generated by Autoconf, you may include it under # the same distribution terms that you use for the rest of that program. thttpd-2.25b/config.sub:# Copyright (C) 1991, 92, 93, 94, 95, 1996 Free Software Foundation, Inc.
thttpd-2.25b/cgi-src/Makefile.in:Copyright(C)1995 by Jef Poskanzer . thttpd-2.25b/cgi-src/phf.c: Copyright(C)1996 by Jef Poskanzer . thttpd-2.25b/cgi-src/redirect.8:Copyright(C)1995 by Jef Poskanzer . thttpd-2.25b/cgi-src/redirect.c: Copyright(C)1995 by Jef Poskanzer . thttpd-2.25b/cgi-src/ssi.8:Copyright(C)1995 by Jef Poskanzer . thttpd-2.25b/cgi-src/ssi.c: Copyright(C)1995 by Jef Poskanzer .
# copyright notice and this permission notice appear in supporting # documentation, and that the name of M.I.T. not be used in advertising or # publicity pertaining to distribution of the software without specific, # written prior permission. M.I.T. makes no representations about the # suitability of this software for any purpose. It is provided "as is" # without express or implied warranty. thttpd-2.25b/strerror.c: * Copyright (c) 1988 Regents of the University of California. * All rights reserved.
© 2009 Koninklijke Philips Electronics N.V. All rights reserved. Document order number: MCI500H_00_UM_V2.
