Register your product and get support at www.philips.com/welcome SQM5822/27 EN Fixed wall mount 1 SQM5822-27_Manual.
Table of contents 1 Important 3 2 Your fixed wall mount 2.1 What’s in the box 2.2 What you’ll also need 3 4 4 3 3.1 3.2 3.3 Installing your wall mount Mounting the wall plate (drywall) Mounting the wall plate (concrete) Attaching the arms to the display 5 5 5 6 4 Mounting and adjusting 7 5 Guarantee and service 8 2 SQM5822-27_Manual.
1 Important Take time to read this manual before you use your wall mount. It contains important information and notes regarding operating your wall mount. © 2009 Koninklijke Philips Electronics N.V. All rights reserved. Reproduction in whole or in part is prohibited without the written consent of the copyright owner. Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners.
2.1 What’s in the box. Wall mount Cotter pin Bag #1 (A) M4x12 Bolt (x4) (B) M4x30 Bolt (x4) (C) M4 Lock Washer (x4) Bag #2 (D) M5x12 Bolt (x4) (E) M5x30 Bolt (x4) (F) M5 Lock Washer (x4) Bag #3 (G) M6x12 Bolt (x4) (H) M6x35 Bolt (x4) (I) M6 Lock Washer (x4) Bag #4 (J) M8x16 Bolt (x4) (K) M8x40 Bolt (x4) (I) M8 Lock Washer (x4) Bag #5 (M) Small Spacer (x4) (N) Large Spacer (x4) (O) M6 Washer (x4) Bag #6 (P) Concrete Anchor (x6) (Q) M8x63 Lag Bolt (x6) (R) Lag Bolt Washer (x6) 2.
3 Installing your wall mount In this chapter, the basic steps to get you started are described. 4 5 B Warning Carefully read the safety precautions in “Section 1 Important” before you install the wall mount. 3.1 Mounting the wall plate (drywall) 6 7 B Warning For safety reasons, this mount must be secured to two adjacent wood studs at least 16” apart.The studs must be capable of supporting the combined weight of the mount and display.
3 4 5 6 7 With the help of another person, place the mount against the wall and level it using the bubble guide. While another person holds the mount in place, mark six locations on the wall where the mount is to be installed. Set the mount aside and drill a 3/8” (10 mm) pilot hole at each marked location. Remove any excess dust from the holes. Insert a concrete anchor (P) into each hole so that it is flush with the concrete surface.
3 4 Attach the arms to the back of your display using the bolts identified in Steps 1 and 2 and the corresponding lock washer (C, F, I, or L).You will need to use the M6 washers (O) if you are using the M4, M5, or M6 bolts. If your display has a curved or recessed back, you may also need to use a spacer (M or N). Make sure the screws are snug, but do not over-tighten. 5 4 Mounting and adjusting 1 With the help of another person, carefully lift your display and place it on the wall plate.
4 Once the tv is fitted properly on to the wall bracket, the security bar must be put into place. 8 8 D Note Slide arm through slots in wall plate & brackets 5 Once the security bar is slid into the appropriate slots, a lock(not provided) may be placed for additional security. 6 A small cotter pint can be used to secure your display to the mount. (included). 9 9 5 Guarantee and service Please contact Philips directly if you have any questions in the installation process of the wall mount.
SQM5822-27_Manual.
© 2009 Koninklijke Philips Electronics All rights reserved. SQM5822-27_Manual.indb 24 SQM5822_27_UM_V2.
