Register your product and get support at www.philips.
Table of contents 1 1.1 1.2 1.3 1.4 1.5 Important Power requirements Conformity Recycling and disposal Electric, Magnetic and Electromagnetic Fields ("EMF") Installation requirements 4 4 4 5 5 6 2 2.1 2.2 Your Wireless TV link What’s in the box Overview of the Wireless TV link 7 7 3 3.1 3.2 Getting started Connect transmitter Install the remote control blaster cord Connect receiver Enjoy Select Source Remove interference on TV2 Improve the quality of the reception with the antenna 9 9 3.3 3.4 3.
1 Important Take time to read this user manual before you use your wireless TV link. It contains important information and notes regarding your wireless TV link. 1.1 Power requirements • Connect the power adapters only to a 100-240V AC 50/60Hz power supply. • The Electrical network is classified as hazardous. The only way to power down the charger is to unplug the power supply from the electrical outlet. Ensure that the electrical outlet is always easily accessible.
1.3 A financial contribution has been paid to the associated national recovery & recycling system. The labeled packaging material is recyclable. Recycling and disposal Disposal instructions for old products. The WEEE directive (Waste Electrical and Electronic Equipment; 2002/96/EC) has been put in place to ensure that products are recycled using best ?available treatment, recovery and recycling techniques to ensure human health and high environmental protection. 1.4 1.
1.5 Installation requirements The product transmits and receives radio waves when it is switched on. The product complies with the standards that are defined for it. As the product is based on RF technology, the quality of the image can be influenced by microwave ovens, Bluetooth, Wifi etc. Therefore the product can suffer from the same kinds of interference as GSMs, portable radios and other RF-based products.
2 Your Wireless TV link Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. 2.1 What’s in the box A. Transmitter C. SCART cable 2.2 D. RCA/SCART cable B. Receiver E. Power F. Remote control G.
Transmitter Control and display elements 2 green: on (source 1) 3 green: on (source 2) 4 Power on/off switch 5 Power input connector (DC 9V) 6 RCA cable entry 7 Antenna 8 Wireless channel selection switch > Select from 4 available channels 9 Remote control blaster cord port 10 SCART cable entry Control and display elements 11 Power light: > green: on 12 Power on/off switch 13 Power input connector (DC 9V) 14 Antenna 15 SCART cable 16 Wireless channel selection switch > Select from 4 available channels Re
3 Getting started 3.1 Connect transmitter c. Plug the RCA connectors into the corresponding ports of the transmitter (A). d. Plug the SCART connector of the RCA/SCART cable into the SCART port of the video source 2. Two video sources can be connected at the same time to the SLV4200 transmitter. The video sources can be following: DVD players/recorders, VCR, Game Consoles, Cable & Satellite Set-TopBoxes, and more. 1 2 Connect video source 1 to the transmitter (A). a.
b. Plug the adapter into the power outlet. 2. 3. c. The green LED on the front panel should be on. Connect the remote control blaster cord (F) to the IR socket. Position the blaster light in front of the video source. Just put it in front of the IR sensor on the front panel. Note: See the FAQ “How can I find the IR sensor on the video source?” for locating the IR sensor on the front panel of the video source. Note: if it is not the case, press the ON/ OFF switch on the back of the product. 5. 3.
- Switch on the Video source. - Take these items: • Receiver (B) • Power adapter (E) • Remote control of the video source. - Go to TV2. 1. Connect the receiver to the second TV (TV2) Plug the SCART cable of the receiver (B) into the SCART port of TV2. Note: if it is not the case, press the ON/ OFF switch on the back of the product. 3. 3.4 Set the CHANNEL switch to the same channel number as on the transmitter (A). Enjoy All the operations listed on 3.1 and 3.3 should have been done. 1. 2. 3. 2.
Note: If the VCR or DVD recorder records a television program, you watch the recorded channel. Note: how to watch a video source on TV1? Use your TV1 and your video source as usual to watch a video source on TV1. Note: In case the video source does not react the IR control blaster might not be installed properly. See the FAQ “How can I find the IR sensor on the video source?” for locating the IR sensor on the front panel of the video source. 3. 4. 3.7 3.
4 Technical Data Transmitter System: RF (TV-LINK) Modulation: FM Weight: 0.27kg Dimensions: 120X182X40.2mm Carrier Frequency: 5750~5855MHz Channels: 4 Radiated Output Power: 25mW Effective Transmission Range: 35m Audio Input level: 2V Video Input level: 1.1V Power requirements: 9V/500mA IR Extender Receiver RF Frequency: 433.
5 Frequently asked questions www.philips.com/support In this chapter, you will find the most frequently asked questions and answers about your product. No image or wrong image on TV1 • Make sure the video source is switched on. • Make sure the video source is connected to the transmitter (A). • Make sure the transmitter (A) is connected to TVI. • Make sure the transmitter (A) is switch on. • Make sure SCART cables are firmly inserted. • Make sure the correct SCART input on TV1 is selected.
Easylink feature does not work. • Check if the TV and VCR support Easylink. • Check if you used full-wired SCART cables. Black and white image with S-VHS VCR. • (Super Video Home System Video/ Cassette/Recorder) • Check if the SCART connector of the S-VHS VCR gives signal in CVBS. (Composite Video Broadcast Signal). See its user manual. How can I find the IR sensor on the video source? • The blaster light needs to be positioned precisely on the IR sensor of the video source.
6 Information 6.1 Warranty One year limited warranty For 12 month from the date of purchase the manufacturer repairs or replaces any faulty product free of charge, subject to proof of purchase, provided the fault has not been caused by improper handling or use, and provided the product has not been damaged, whether as a result of an accident or of repair by others than the manufacturer. 6.2 Glossary CVBS: Video standard for showing colors on a TV.
7 INDEX C Channel 12 Connect receiver 10 Connect transmitter 9 E Enjoy 11 F Frequently asked questions 14 G Getting started 9 I Information 16 Interference 12 O Overview of the Wireless TV link 7 R Remote control blaster cord 10 T Technical Data 13 W What’s in the box 7 Y Your Wireless TV link 7 INDEX 17
8 Declaration of Conformity
© 2009 Koninklijke Philips Electronics N.V. All rights reserved. Reproduction in whole or in part is prohibited without the written consent of the copyright owner. Document number: SLV4200_12_EN_UM_V1.
