S7000 series
1 2 16 17 18 19 20 21 3 4 13 14 11 12 5 6 7 8 9 10 15
6 English Contents Introduction_______________________________________________________ General description_______________________________________________ What do the icons on my appliance handle mean?_____________ What does the icon on my Quick Clean Pod mean?_____________ How do I charge my appliance?__________________________________ How do I use my appliance and the attachments?______________ How do I clean my appliance and the attachments?____________ How do I use the Quick Clean Pod?_________________
English 7 15 Cleaning brush 16 Length settings 17 Click-on beard styler attachment 18 Comb for beard styler attachment 19 Attachment holder 20 Click-on cleansing brush attachment 21 Click-on nose trimmer attachment Note: The accessories supplied may vary for different products. The box shows the accessories that have been supplied with your appliance. What do the icons on my appliance handle mean? Icon Behavior Meaning Pulsing The cleaning program is in progress.
8 English Icon Behavior Meaning Flashing quickly when you remove the shaver from the Quick Clean Pod or press the on/off button during the cleaning program The cleaning program was stopped. If you wish to continue, you need to restart the cleaning cycle by putting the shaver into the Quick Clean Pod and pressing the on/off button. Lights up The SkinIQ is actively detecting your shaving behavior. Lights up green The correct shaving motion (circular movements) was used.
English Icon Behavior 9 Meaning Bottom light flashing orange The battery is almost empty (see 'How do I charge my appliance?'). Lights flashing in sequence The appliance is charging. Lights up continuously The appliance is fully charged. What does the icon on my Quick Clean Pod mean? Icon Behavior Meaning Becomes visible on the Quick Clean Pod The Quick Clean Pod Cartridge needs to be replaced (see 'How do I use the Quick Clean Pod?').
10 English 2 Insert the small plug into the appliance and put the supply unit in the wall socket. - While the appliance is in quick charge mode, the lights of the battery status indicator light up one after the other. After approximately 5 minutes, the bottom light of the battery status indicator flashes. The battery now contains enough energy for one shave. - While the appliance charges, first the bottom light of the battery status indicator flashes and then lights up continuously.
English 11 - As the appliance continues to charge, the light ring becomes brighter and rotates slower. - When the appliance is fully charged, the light ring lights up fully and stops rotating. 4 After charging, remove the supply unit from the wall socket and pull the small plug out of the charging stand. 'Unplug for use' symbol The 'unplug for use' symbol flashes to remind you to disconnect the appliance from the wall socket and remove the small plug from the appliance before you switch it on.
12 English start with the guided shave to enhance your shaving experience. - Correct handling of your appliance will contribute to the best shaving result. - Follow the advice obtained from the synchronized shaves and the personalized programs. Shaving You can use this appliance either wet or dry, or even under the shower. For a wet shave, apply some water and shaving foam or gel to your skin and rinse the shaving heads under the tap with warm water before following the steps below.
English 13 3 Use the narrow sides of the shaving unit to shave in hard-to-reach areas such as along your jawline and under your nose. 4 Switch off and clean the appliance after each use. Note: Make sure you rinse all foam or shaving gel off the appliance. SkinIQ motion guidance: When you have finished shaving you receive feedback on the handle. The motion feedback icon lights up in various colors, giving you feedback on your overall shave.
14 English - Clean the appliance and attachments after each use to prevent clogging and damage (see 'How do I clean my appliance and the attachments?'). - Clean the shaving heads thoroughly once a month or when the appliance does not shave as well as it used to (see 'Thorough cleaning'). Synchronize your shaves This shaver stores your shave data so you don't need to take your smartphone with you when you shave. When the data storage is almost full, the notification symbol flashes.
English 15 4 You can also use the trimmer under your nose. 5 Switch off the appliance and clean the trimmer after each use to prevent clogging and damage (see 'How do I clean my appliance and the attachments?'). 6 Close the trimmer. Using the click-on attachments Note: The accessories supplied may vary for different products. The box shows the accessories that have been supplied with your product.
16 English 3 Press the length selector and then push it to the left or right to select the desired hair length setting. 4 Switch on the appliance. 5 Move the appliance upwards while you exert gentle pressure. Make sure the front of the comb is in full contact with the skin. 6 Switch off the appliance and clean the attachment after use.
English 17 Using the nose/ear trimmer attachment You can use the nose/ear trimmer attachment to trim your nose and/or ear hair. Trimming nose hair Make sure both the nose/ear trimmer attachment and nasal passages are clean before trimming. 1 Twist the shaving head or other attachment to remove it from the handle and press the nose/ear hair trimmer onto the handle. 2 Switch on the appliance. 3 Carefully insert the trimming head into one of your nostrils. Do not insert the attachment more than 0.
18 English Do not insert the trimming head more than 0.5 cm into your ear channel, as this could damage the eardrum. 4 Slowly turn the trimming head around to remove all unwanted hairs from your outer ear channel. 5 Switch off the appliance and clean the attachment after use. Using the cleansing brush attachment Use the cleansing brush with your daily cleansing cream to remove oil and dirt. We advise you to use it no more than once a week.
English 19 7 After approx. 20 seconds, move the appliance to your other cheek and start cleansing this part of your face. 20 sec. 20 sec. 8 After approx. 20 seconds, move the appliance to your forehead and start cleansing this part of your face. Gently move the brush head from left to right. We advise you to not overdo the cleansing and to not cleanse any zone longer than 20 seconds. 9 Switch off the appliance and clean the attachment after use. 10 After the treatment, rinse and dry your face.
20 English Press the on/off button for 3 seconds to use the travel lock mode. 3 sec. When the travel lock is activated, the travel lock symbol flashes. Note: Bluetooth is switched off when the travel lock is activated. Deactivating the travel lock Press the on/off button for 3 seconds. Once the travel lock is deactivated, the appliance switches on automatically. Note: The shaver unlocks automatically when it is connected to a wall socket.
English 21 3 Switch off the shaver. Press the release button to open the shaving unit. 4 Rinse the hair chamber under a warm tap. 5 Rinse the shaving head holder under a warm tap. 6 Carefully shake off excess water and let the shaving head holder air-dry completely. 7 Close the shaving unit. Thorough cleaning We advise you to clean the shaving heads thoroughly once a month or when the shaver does not shave as well as it used to.
22 English 2 Press the release buttons on the shaving unit and pull the shaving head holder off the shaving unit. 3 Rinse the hair chamber and shaving head holder under the tap. 4 Remove the shaving heads. For detailed instructions, see 'How do I replace the shaving heads?.' Note: Do not clean more than one cutter and guard at a time, since they are all matching sets. If you accidentally put a cutter in the wrong shaving guard, it may take several weeks before optimal shaving performance is restored.
English 23 1 Make sure that the appliance is switched off and disconnected from the wall socket. 2 Push the trimmer release slide down to open the pop-up trimmer. 3 Switch on the appliance and rinse the pop-up trimmer with warm water. 4 After cleaning, switch off the appliance. 5 Carefully shake off excess water and let the pop-up trimmer air dry. 6 Close the trimmer. Tip: For optimal performance, lubricate the teeth of the pop-up trimmer with a drop of mineral oil every six months (oil not included).
24 English 3 Clean the parts thoroughly with warm water. Use soap only on the cleansing brush attachment. Tip: If rinsing the nose/ear trimmer attachment under the tap is not sufficient, press the attachment onto handle and immerse the trimming head in a glass with warm water for a few minutes. Then switch on the appliance and rinse it under the tap. 4 Carefully shake off excess water from the beard styler, combs and nose/ear trimmer attachments and let them air dry completely.
English 25 3 Lift the tab on the seal and pull it by the corner to remove the seal from the Quick Clean Pod Cartridge. 4 Press the small circular piece on the handle of the Quick Clean Pod Cartridge to break the snap hook on the handle. 5 Place the Quick Clean Pod Cartridge into the Quick Clean Pod. 6 Put the top of the Quick Clean Pod back onto the base and turn it clockwise until you hear a click. Do not tilt the Quick Clean Pod to prevent leakage.
26 English Clean Pod (see 'How do I clean my appliance and the attachments?'). Always shake excess water off the shaver before you place it in the Quick Clean Pod. 1 Place the shaver upside down into the Quick Clean Pod. The shaver automatically detects that it is in the Quick Clean Pod. 2 Switch on the shaver to start the cleaning program. Each cleaning program takes approximately one minute. During the cleaning program the cleaning symbol lights up continuously and the blue icon pulses.
English 1 27 Twist and remove the top of the Quick Clean Pod. 2 Lift the Quick Clean Pod Cartridge out of the Quick Clean Pod by the handle. 3 Pour any remaining fluid down a drain and recycle the empty cartridge in accordance with local waste regulations. 4 Place a new Quick Clean Pod Cartridge into the Quick Clean Pod (see 'Preparing the Quick Clean Pod for use'). Scan the QR code to the left or visit www.philips.com/cleaning-cartridge to order replacement Quick Clean Pod Cartridges.
28 English shave data to be synced later so you don't need to take your smartphone with you when you shave. The first few times you switch on the shaver, the notification symbol flashes if no connection is established with a smartphone. You can switch off Bluetooth on your shaver by activating the travel lock (see 'Storage and travel'). 3 sec. Pair the shaver and smartphone You can use the app to synchronize your shave data, change your personal settings and get routine-based coaching.
English 29 3 Switch on the shaver. 4 Open the app and follow the instructions to start the pairing process. 5 Once paired, the shaver and app connect automatically when the app is open and Bluetooth on your phone is switched on. Notification symbol The shaver is equipped with a notification symbol. The notification symbol lights up when there is an important message for you in the app. When it lights up, simply open the app on your smartphone and follow the easy tips that the app gives you.
30 English How do I replace the shaving heads? For maximum shaving performance, we advise you to replace the shaving heads every two years. Replace damaged shaving heads immediately. Always replace the shaving heads with original Philips shaving heads (see 'Ordering accessories'). Replacing the shaving heads 1 Switch off the shaver. 2 Press the release buttons on the shaving unit and pull the shaving head holder off the shaving unit. 2 3 Turn the retaining rings anticlockwise and remove them.
English 31 6 Place the retaining rings back onto the shaving heads and turn them clockwise to reattach the retaining ring. 1 2 - Each retaining ring has two recesses that fit exactly into the projections of the shaving head holder. Turn the ring clockwise until your hear a click to indicate that the ring is fixed. Note: Hold the shaving head holder in your hand when you reinsert the shaving heads and reattach the retaining rings.
32 English - CC12 Philips Quick Clean Pod Cartridge 2-pack - CC13 Philips Quick Clean Pod Cartridge 3-pack - CC16 Philips Quick Clean Pod Cartridge 6-pack Note: The availability of the accessories may differ by country. Troubleshooting This chapter summarizes the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, visit www.philips.
English Problem Possible cause 33 Solution Make sure that your smartphone is within one meter of your shaver to enable a Bluetooth connection. Make sure your shaver is charged. I want to use the shaver without the app. The appliance does not work when I press the on/off button. You do not have to connect your shaver with your smartphone before each shave. To get personalized shaving tips, just make sure that you connect it at least once every 20 shaves to synchronize your shave data.
34 English Problem Water is leaking from the bottom of the appliance. Possible cause Solution Hairs or dirt obstruct the shaving heads. Clean the shaving heads thoroughly. During cleaning, water may collect between the inner body and the outer shell of the appliance. This is normal and not dangerous because all electronics are enclosed in a sealed power unit inside the appliance.
English My Philips Quick Clean Pod is overflowing. 35 The shaver battery is empty. Charge the shaver before using the Philips Quick Clean Pod. You regularly use the Philips Quick Clean Pod after rinsing the shaver but not shaking off excess water. Shake off excess water after rinsing the shaving heads each time before putting the shaver into the Philips Quick Clean Pod. You shaved with shaving gel or foam and did not rinse the shaver before using the Philips Quick Clean Pod.
© 2020 Koninklijke Philips N.V. All rights reserved 3000.057.1983.
