Technical data

ManualsBrandsPhilips ManualsTVPFL6 Series

Protective Devices

Residual Current Devices PF7

• Residual current devices

• Shape compatible with and suitable for standard busbar connection to

other devices of the P-series

• Twin-purpose terminal (lift/open-mouthed) above and below

• Busbar positioning optionally above or below

• Free terminal space despite installed busbar

• Universal tripping signal switch, also suitable for PL., PFL., Z-A. can be

mounted subsequently

• Auxiliary switch Z-HK can be mounted subsequently

• Contact position indicator red - green

• Delayed types suitable for being used with standard fluorescent tubes with

or without electronical ballast (30mA-RCD: 30 units per phase conductor,

100mA-RCD: 90 units per phase conductor)

Notes: Depending of the fluorescent lamp ballast manufacturer partly more

possible. Symmetrical allocation of the fluorescent lamp ballasts on all

phases favourably. Shifting references of the fluorescent lamp ballast man-

ufacturer consider.

• The device functions irrespective of the position of installation

• Tripping is line voltage-independent. Consequently, the RCD is suitable for

“fault current/residual current protection” and “additional protection” with-

in the the meaning of the applicable installation rules

• Mains connection at either side

• Types with 80 a 100 A permissible short-circuit back-up fuse (PF7-80,

PF7-100): Take into account overload protection

• The 4-pole device can also be used for 3-pole connection.

For this purpose use terminals 1-2, 3-4, and 5-6 (+ cable link).

• The 4-pole device can also be used for 2-pole connection.

For this purpose use terminals 5-6 and N-N.

• The test key “T” must be pressed every month. The system operator must

be informed of this obligation and his responsibility in a way that can be

proven (self-adhesive RCD-label enclosed)

• Pressing the test key “T” serves the only purpose of function testing the

residual current device (RCD). This test does not make earthing resistance

measurement (R

), or proper checking of the earth conductor condition

redundant, which must be performed separately.

• Type -A: Protects against special forms of residual pulsating DC which

have have not been smoothed

• Type -G: High reliability against unwanted tripping. Compulsory for any cir-

cuit where personal injury or damage to property may occur in case of

unwanted tripping (ÖVE/ÖNORM E 8001-1 § 12.1.6).

• Type -G/A: Additionally protects against special forms of residual pulsating

DC which have not been smoothed.

Special types for X-ray application PF7-...-R

• Type -S: Selective residual current device sensitive to AC, type -S.

Compulsory for systems with surge arresters downstream of the RCD

(ÖVE/ÖNORM E 8001-1 § 12.1.5).

• Type -S/A: Additionally protects against special forms of residual pulsating

pulsating DC which have not been smoothed.

Accessories:

Auxiliary switch for

subsequent installation to the left Z-HK 248432

Tripping signal contact for

subsequent installation to the right Z-NHK 248434

Remote control and

automatic switching device Z-FW/LP 248296

Compact enclosure KLV-TC-2 276240

KLV-TC-4 276241

Sealing cover set Z-RC/AK-2TE 285385

Z-RC/AK-4TE 101062

Switching interlock IS/SPE-1TE 101911

Technical Data

Electrical

Design according to IEC/EN 61008

Type G acc. to ÖVE E 8601

Current test marks as printed onto the device

Tripping instantaneous

Type G 10 ms delay

Type S 40 ms delay -

with selective disconnecting

function

Rated voltage U

230/400 V, 50 Hz

Rated tripping current I

Δn

10, 30, 100, 300, 500 mA

Sensitivity AC and pulsating DC

Rated insulation voltage U

440 V

Rated impulse withstand voltage U

imp

4 kV

Rated short circuit strength I

10 kA

Maximum back-up fuse Overload Short circuit

= 16-40 A 25 A gG/gL 63 A gG/gL

= 63 A 40 A gG/gL 63 A gG/gL

= 80 A 50 A gG/gL 80 A gG/gL

= 100 A 63 A gG/gL 100 A gG/gL

Rated breaking capacity I

Rated fault breaking capacity I

Δm

= 16-40 A 500 A

= 63 A 630 A

= 80 A 800 A

= 100 A 1,000 A

Voltage range of test button 2-pole 184 - 250 V~

4-pole 184 - 440 V~

Endurance

electrical comp. ≥ 4,000 operating cycles

mechanical comp. ≥ 20,000 operating cycles

Mechanical

Frame size 45 mm

Device height 80 mm

Device width 35 mm (2MU),

70 mm (4MU)

Mounting quick fastening with

2 lock-in positions on

DIN rail IEC/EN 60715

Degree of protection, built-in IP40

Deg. of prot. in moisture-proof encl. IP54

Upper and lower terminals open mouthed/lift terminals

Terminal protection finger and hand touch safe,

BGV A3, ÖVE-EN 6

Terminal capacity 1x (1.5 - 35) mm

single wire

2x (1.5 - 16) mm

multi wire

Busbar thickness 0.8 - 2 mm

Tripping temperature -25°C to +40°C

Storage- and transport temperature -35°C to +60°C

Resistance to climatic conditions 25-55°C/90-95% relative

humidity acc. to IEC 60068-2

Connection diagrams

2-pole 4-pole