Technical data

ManualsBrandsPhilips ManualsTVPFL6 Series

Protective Devices

Residual Current Devices dRCM - digital, types B and B+

• Residual current devices, all-current sensitive

• Shape compatible with and suitable for standard busbar connection to

other devices of the P-series

• Twin-purpose terminal (lift/open-mouthed) above and below

• Busbar positioning optionally above or below

• Free terminal space despite installed busbar

• Universal tripping signal switch, also suitable for PLS., PKN., ZP-A. can be

mounted subsequently

• Auxiliary switch Z-HK can be mounted subsequently

• Contact position indicator red - green

• Tripping indicator white - blue

• Additional Safety

- possibility to seal

- possibility to lock in ON and OFF position

• Delayed types (G, S) suitable for being used with standard fluorescent

tubes with or without electronical ballast (30mA-RCD: 30 units per phase

conductor, 100mA-RCD: 90 units per phase conductor)

Notes: Depending of the fluorescent lamp ballast manufacturer partly more

possible. Symmetrical allocation of the fluorescent lamp ballasts on all

phases favourably. Shifting references of the fluorescent lamp ballast man-

ufacturer consider.

• The device functions irrespective of the position of installation

• Tripping is line voltage-independent. Consequently, the RCD is suitable for

“fault current/residual current protection” and “additional protection” with-

in the meaning of the applicable installation rules

• The 4-pole device can also be used for 3-pole connection:

See connection possibilities.

• The 4-pole device can also be used for 2-pole connection:

See connection possibilities.

• The test key “T” must be pressed every year. The system operator must be

informed of this obligation and his responsibility in a way that can be

proven. The yearly test interval is only valid for residential and similar

applications. Under all other conditions (e.g. damply or dusty environ-

ment), it's recommended to test in shorter intervals (e.g. monthly).

A test is further needed if red and yellow LED are on together.

• Pressing the test key “T” serves the only purpose of function testing the

residual current device (RCD). This test does not make earthing resistance

measurement (R

), or proper checking of the earth conductor condition

redundant, which must be performed separately.

• Functioning

- The green LED becomes active at 0-30% I

Δn

- The yellow LED becomes active at 30-50% I

Δn

- The red LED becomes active at >50% I

Δn

• Potential-free relay (NO contact, in parallel with the yellow LED, up to 1 A

ohmic load / 230 V~) for external prewarning function. Bistabile, means the

warning stays on also when the breaker trips, until reset.

• Type -G/B und G/B+: High reliability against unwanted tripping.

Compulsory for any circuit where personal injury or damage to property

may occur in case of unwanted tripping (ÖVE/ÖNORM E 8001-1 § 12.1.6).

Protection against all types of fault currents.

• Type -S/B und S/B+: Selective residual current device. Protection against

all types of fault currents.

Accessories:

Auxiliary switch for

subsequent installation to the left Z-HK 248432

Tripping signal contact for

subsequent installation to the right Z-NHK 248434

Remote control and

automatic switching device Z-FW/LP 248296

Compact enclosure KLV-TC-4 276241

Sealing cover set Z-RC/AK-4TE 101062

Switching interlock IS/SPE-1TE 101911

Technical Data

Electrical

Design according to IEC/EN 61008

IEC/EN 62423

B+ Type acc. to

VDE 0664-400

Formerly known as

VDE V 0664-110

Type G/B and G/B+

acc. to ÖVE E 8601

Current test marks as printed onto the device

Tripping Type G 10 ms delay

Type S 40 ms delay -

with selective disconnecting

function

Rated voltage U

230/400 and 240/415 V AC,

50 Hz

Operation voltage electronic 50 – 254V AC

Operation voltage test circuit 184 – 440V AC

Rated tripping current I

Δn

30, 300 mA

Sensitivity Alternating, pulsed and

direct currents

Rated insulation voltage U

440 V

Rated impulse withstand voltage

imp

4 kV (1.2/50 µs)

Rated short circuit capacity I

10 kA

Peak withstand current

Type G/B and G/B+ 3 kA (8/20 µs)

surge current proof

Type S/B and S/B+ typ. 5 kA (8/20 µs)

selective + surge current

proof

Electrical isolation > 4 mm contact space

Maximum back-up fuse Short circuit and

overload protection

= 16-63A 63 A gG/gL

= 80A 80 A gG/gL

Endurance

electrical comp. ≥ 4,000 operating cycles

mechanical comp. ≥ 20,000 operating cycles

Mechanical

Frame size 45 mm

Device height 80 mm

Device width 70 mm (4MU)

Mounting quick fastening with

2 lock-in positions on

DIN rail IEC/EN 60715

Degree of protection, built-in IP40

Deg. of prot. in moisture-proof encl. IP54

Upper and lower terminals open mouthed/lift terminals

Terminal protection finger and hand touch safe,

BGV A3, ÖVE-EN 6

Terminal capacity 1.5 - 35 mm

single wire

2 x 16 mm

multi wire

Terminal screw M5 (Pozidriv PZ2)

Terminal capacity warning contact(s)

0.25-1.5 mm

(plug in terminals)

Terminal torque 2 - 2.4 Nm

Busbar thickness 0.8 - 2 mm

Tripping temperature -25°C to +40°C

Storage- and transport temperature -35°C to +60°C

Resistance to climatic conditions 25-55°C/90-95% relative

humidity acc. to IEC 60068-2

Contact position indicator red / green

Tripping indicator white / blue

Connection diagram

4-pole

Last

Load

Netz

Mains