Micro Hi-Fi System pg001-020_MCM240_21_Eng 1 MCM240 2005.5.
México Es necesario que lea cuidadosamente su instructivo de manejo. PRECAUCIÓN - ADVERTENCIA No abrir, riesgo de choque eléctrico ATENCIÓN Verifique que el voltaje de alimentación sea el requerido para su aparato Para evitar el riesgo de choque eléctrico, no quite la tapa. En caso de requerir servicio, dirijase al personal calificado. Microsistema de Audio MCM240/21 110–127 / 220–240V~; 50–60 Hz 7W Philips Mexicana, S.A. de C.V. Av. La Palma No.6 Col.
1 3 ! 5 7 # $ @ 0 8 % * & ^ ( ) 2 5 1 3 4 6 7 8 ! 9 0 3 pg001-020_MCM240_21_Eng 3 3 2005.5.
pg001-020_MCM240_21_Eng 4 2005.5.
English Index Français English ------------------------------------------------ 6 Español Français -------------------------------------------- 21 Español --------------------------------------------- 36 -------------------------------------------------------- 51 5 pg001-020_MCM240_21_Eng 5 2005.5.
Contents English General Information Radio Reception Environmental information ................................ 7 Supplied accessories ............................................ 7 Safety information ................................................ 7 Tuning to radio stations .................................... 15 Programming radio stations ............................. 15 Automatic programming Manual programming Tuning to preset radio stations ....................... 15 Changing tuning grid .........
IMPORTANT! PLEASE NOTE THAT THE VOLTAGE SELECTOR LOCATED AT THE BOTTOM OF THIS SYSTEM IS PRESET AT 220V FROM THE FACTORY. FOR COUNTRIES THAT OPERATE AT 110V-127V, PLEASE ADJUST TO 110V-127V BEFORE YOU SWITCH ON THE SYSTEM. Environmental Information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet).
Preparations English FM wire antenna MW loop antenna Speaker (left) Speaker (right) VOLTAGE SELECTOR 110V127V 220V240V NOT FOR ALL VERSIONS AC power cord Rear connections B Antennas Connection The type plate is located at the rear of the system. A Power Connect the supplied MW loop antenna and FM antenna to the respective terminals. Adjust the position of the antenna for optimal reception.
FM Antenna English Preparations Before using the remote control 1 2 ● For better FM stereo reception, connect an outdoor FM antenna to the FM ANTENNA terminal. 3 Pull out the plastic protective sheet. Select the source you wish to control by pressing one of the source select keys on the remote control (for example CD, TUNER). Then select the desired function (for example ÉÅ , í , ë).
Controls (illustrations on page 3) English Controls on the system and remote control @ DISPLAY/CLOCK – – 1 STANDBY-ONB # – – switches the system on or to standby. sets the clock function. displays disc information during playback. TIMER activates/ deactivates or sets the timer function. 2 Display screen $ SLEEP – – shows the status of the system. activates/deactivates or selects the sleeper time. 3 OPEN • CLOSEç % DSC (Digital Sound Control) – – opens/closes the CD door.
English Basic Functions Adjusting volume and sound Important! Before you operate the system, complete the preparation procedures. 1 Press VOLUME 3 / 4 (+/-) to decrease or increase the volume. ➜ Display shows the volume level VOL and a number from MIN1, 2, ...30, 31 MAX. 2 Press DSC repeatedly to select the desired sound effect: ROCK/ JAZZ/ POP/ CLASSIC. 3 Press DBB to switch bass enhancement on or off. ➜ Display shows: DBB.
CD/MP3-CD Operation English Basic playback controls To play a disc ● Press ÉÅ to start playback. ➜ The current track number and elapsed playing time of the track are displayed during disc playback. To select a different track ● Press PRESETí / ë (or í / ë on the remote) once or repeatedly until the desired track number appears in the display. ● If you have selected a track number shortly after loading a disc or in the PAUSE position, you will need to press ÉÅ to start playback.
Notes: CD play will also stop when; – the CD door is opened. – the disc has reached the end. – you select another source: TUNER or AUX. – you select standby. – the set auto off time arrives. – no button is pressed within 15 minutes in the CD PAUSE position. REPEAT ............ plays the current track continuously 1 2 Playing an MP3 disc 1 2 3 4 Load an MP3 disc. ➜ The disc reading time may exceed 10 seconds due to the large number of songs compiled into one disc.
CD/MP3-CD Operation English 3 4 5 Press PROGRAM to confirm the track number to be stored. ➜ PROG X is shown briefly, followed by the number of the track (for MP3-CD, the album and title numbers of the track) you just stored. X denotes the next program number to be stored Repeat steps 2-3 to select and store all desired tracks. ➜ FULL is displayed if you attempt to program more than 40 tracks. To star t playback of your disc program, press STOP 9 followed by ÉÅ or press ÉÅ directly.
1 English Radio Reception Press PRESETí / ë (or í / ë on the remote) to select the preset number where programming should start. Note: – If no preset number is selected, default is preset (1) and all your presets will be overridden. 2 Press PROGRAM for more than 2 seconds to activate programming. ➜ AUTO is displayed and available stations are programmed in order of waveband reception strength: FM followed by MW. The last preset automatically stored will then be played.
Radio Reception English Changing tuning grid (not available for all versions) In North and South America, the frequency step between adjacent channels in the MW band is 10 kHz (9 kHz in some areas). Changing the tuning grid will erase all previously stored preset radio stations. 1 2 Select TUNER source or in the tuner mode. Press STOP on the set for at least 5 seconds. ➜ The display will show "GRID 9" or "GRID10".
1 Setting the clock 1 2 3 In standby mode or system on, press and hold DISPLAY/CLOCK on the remote control for more than 3 seconds. ➜ SET CLOCK scrolls on the display. ➜ The clock digits for the hours flash. Press VOLUME (3 / 4) (+/-) to set the hours. Press DISPLAY/CLOCK again. ➜ The clock digits for the minutes flash. 4 Press VOLUME (3 / 4) (+/-) to set the minutes. 5 Press DISPLAY/CLOCK to confirm the time. Note: – The backlight for clock display is dim in standby.
Clock/Timer English Activating and deactivating SLEEP The sleep timer enables the system to switch off by itself after a set period of time. ● Press SLEEP on the remote control once or more. ➜ Display shows SLEEP and one of the sleep time options in sequence: 90, 60, 45, 30, 15, OFF, 90... if you have selected a time. Once SLEEP is activated, SLEEP is display. ● To deactivate, press SLEEP on the remote control repeatedly until OFF is shown, or press STANDBY-ON (or B on the remote). ➜ OFF is displayed.
AMPLIFIER Output power .......................................... 2 x 5 W RMS ......................................................................... 200 W PMPO Signal-to-noise ratio ....................................... ≥ 62 dBA Frequency response ......... 63 – 16000 Hz, ± 3 dB Input sensitivity AUX ....................... 0.5 V (max. 2 V) Impedance loudspeakers ......................................... 4 Ω Impedance headphones .................... 32 Ω -1000 Ω ........................................
Troubleshooting English WARNING Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. Do not open the system as there is a risk of electric shock. If a fault occurs, first check the points listed below before taking the system for repair. If you are unable to remedy a problem by following these hints, consult your dealer or Philips for help. Problem Solution “NO DISC” is displayed. ✔ Insert a disc. ✔ Check if the disc is inserted upside down.