Micro Hi-Fi System MCM148 Register your product and get support at www.philips.com/welcome User manual 用戶手冊 MCM148_96_UM.
CAUTION Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. 2 MCM148_96_UM.
MCM148_96_UM.
English----------------------------------------------------- 6 English 中文----------------------------------------------第 21 頁 中文 Index 5 MCM148_96_UM.
Contents English General Information Supplied accessories...........................................................7 Environmental Information.............................................7 Safety Information................................................................7 Hearing Safety........................................................................8 Preparations Rear connections..................................................................9 Inserting batteries into the Remote Control......
● Install the unit near the AC outlet and where the AC power plug can be easily reached. ● Place the system in a location with adequate ventilation to prevent internal heat build-up in your system. Allow at least 10 cm (4 inches) clearance from the rear and the top of the unit and 5 cm (2 inches) from each side. ● The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc.
General Information Be sure to observe the following guidelines when using your headphones. English Hearing Safety Listen at a moderate volume. ● ● Using headphones at a high volume can impair your hearing. This product can produce sounds in decibel ranges that may cause hearing loss for a normal person, even for exposure less than a minute. The higher decibel ranges are offered for those that may have already experienced some hearing loss. Sound can be deceiving.
English Preparations Rear connections The type plate is located at the rear of the system. A Power – Before connecting the AC power cord to the wall outlet, ensure that all other connections have been made. – If your system is equipped with a Voltage Selector, set the VOLTAGE SELECTOR to the local power line voltage. Warning! – For optimal performance, use only the original power cable. – Never make or change any connections with the power switched on.
Preparations English Inserting batteries into the Remote Control 1 2 3 Using the Remote Control to operate the system Open the battery compartment. 1 Insert two R03 or AAA batteries following the indications (+/-) inside the compartment. Close the cover. Aim the Remote Control directly at the remote sensor (IR) on the front panel. 2 Do not put any objects between the Remote Control and the system while operating the system.
Controls on the system and remote control STANDBY ON 2(PWR) switches the system to standby or on. iR SENSOR infrared sensor for remote control. SOURCE selects the respective sound source for CD/ TUNER/AUX. – switches on the system. 4 ALBUM/PRESET +/for radio................selects a preset radio station. for MP3/WMA.....selects an album. 5 DBB (Dynamic Bass Boost) – enhances the bass. 6 TUNING 4 ¢ for Tuner................tunes to radio stations. for CD....................
Basic Functions English To exit without storing the plug and play ● STANDBY-ON MICR O SYSTE M MCM148 iR MP3-CD/CD-R/CD-RW COMPATIBLE SOURC E Note: – During Plug and Play, if no button is pressed within 15 seconds, the system will exit Plug and Play mode. VOL ALBUM/ PRESET TUNING MODE Press 9 on the system. ➜ If you do not complete the Plug and Play installation, the function will be restarted when you next turn on the main supply again.
CD/MP3 Operation STANDBY-ON To play a disc MICR O SYSTE M MCM148 ● iR MP3-CD/CD-R/CD-RW COMPATIBLE SOURC E Press 2; to start playback. ➜ The current track number and elapsed playing time of the track are displayed during disc playback. To select a different track VOL ALBUM/ PRESET TUNING English Basic playback controls MODE PROG ● Press TUNING 4 ¢ (on the remote control ¡ / ™) once or repeatedly until the desired track number appears in the display.
CD/MP3 Operation English 3 Press TUNING 4 ¢ (on the remote control ¡ / ™) to select a desired track. 4 ● Press 2; to start playback. During playback, press CLOCK/DISPLAY on the remote control to show the title name, album name, ID3 information and clock time. Supported MP3 disc formats: – ISO9660, Joliet, UDF 1.5 – Maximum title number: 999 (depending on filename length) – Maximum album number: 99 – Supported sampling frequencies: 32 kHz, 44.
1 STANDBY-ON MICR O SYSTE M MCM148 Press ALBUM/PRESET +/- to select the preset number where programming should start. English Radio Reception Note: – If no preset number is selected, default is preset (1) and all your presets will be overridden. iR MP3-CD/CD-R/CD-RW COMPATIBLE 2 SOURC E VOL ALBUM/ PRESET TUNING MODE PROG VOL DBB Press PROG. for more than 2 seconds to activate programming. ➜ AUTO is displayed and available stations are programmed in order of waveband reception strength.
Other Connection English Listening to an external source You can listen to the sound of the connected external device through your system’s speakers. 1 Press SOURCE on the set repeatedly or press AUX on the remote control to select AUX source. 2 Use a cinch cable (not supplied) to connect MCM148’s AUX jack (3.5 mm, located on the back panel) to an AUDIO OUT or headphone jack on an external equipment (such as CD player, or VCR).
STANDBY-ON 5 Press TIMER again. ➜ The clock digits for the minutes flash. 6 Press TUNING 4 ¢ (à / á on the remote control) to set the minutes. 7 Press TIMER to confirm the time. ➜ The timer is now set and activated. MICR O SYSTE M MCM148 iR MP3-CD/CD-R/CD-RW COMPATIBLE SOURC E VOL Notes: . – If CD source is selected and no disc is in the CD tray or the disc has an error,TUNER will be selected automatically.
Specifications English Amplifier Output power ............................................2 x 2W RMS Signal-to-noise ratio............................≥ 60 dBA (IEC) Frequency response.......................... 125 – 16000 Hz Impedance loudspeakers..............................................4Ω CD player Frequency range.................................. 125 – 16000 Hz Signal-to-noise ratio..............................................65 dBA Tuner FM wave range......................................87.
WARNING Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. Do not open the system as there is a risk of electric shock. English Troubleshooting If a fault occurs, first check the points listed below before taking the system for repair. If you are unable to remedy a problem by following these hints, consult your dealer or Philips for help. Solution Problem “NO DISC” is displayed. ✔ Insert a disc. ✔ Check if the disc is inserted upside down.
Troubleshooting English Solution Problem The remote control does not function properly. ✔ Select the source (CD or TUNER, for example) before pressing the function button (É,í,ë). ✔ Reduce the distance between the remote control and the system. ✔ Insert the batteries with their polarities (+/– signs) aligned as indicated. ✔ Replace the batteries. ✔ Point the remote control directly towards the IR sensor. The time is not working. ✔ Set the clock correctly.
Meet Philips at the Internet http://www.philips.com English 中文 MCM148 CLASS 1 LASER PRODUCT C 2009 Koninklijke Philips Electronics N.V. All rights reserved. Printed in China MCM148_96_UM.indb 34 MCM148_96_UM_V1.
