Micro Hi-Fi System Register your product and get support at www.philips.com/welcome.
4 1 5 2 OP E N / C LO S E 6 7 3 STANDBY-ON SOURCE BAND PROG/CLOCK - VOLUME + TUNING M I C R O S Y S T E M M C M1 0 8 8 iR 0 ! @ # 9 AUX-IN 1
General English Information Congratulations on your purchase IMPORTANT! Controls on the system and and welcome to Philips! PLEASE NOTE THAT THE VOLTAGE remote control To fully benefi t from AT theTHE support SELECTOR LOCATED REARthat OF Philips offers, IS register your product at SYSTEM PRESET AT 220V FROM BAND 1 THIS www.philips.welcome.com FACTORY. COUNTRIES THAT – THE for Tuner (on the FOR set only) selects waveband.
General English Information 1 – 2 – – IMPORTANT! Controls on the system and PLEASE NOTE THAT THE VOLTAGE remote control SELECTOR LOCATED AT THE REAR OF THIS SYSTEM IS PRESET AT 220V FROM BAND THE FACTORY. COUNTRIES THAT for Tuner (on the FOR set only) selects waveband. OPERATE AT 110V-127V, PLEASE ADJUST SOURCE (CD/ TUNER/ AUX) TO 110V-127V BEFORE YOU SWITCH ON switches on the system. THE SYSTEM. selects the respective sound source for CD/ FM/ MW/ AUX.
Preparations MW loop antenna FM wire antenna Speaker (left) Speaker (right) AC power cord Rear connections The type plate is located at the rear of the system. A Power – Before connecting the AC power cord to the wall outlet, ensure that all other connections have been made. – If your system is equipped with a Voltage Selector, set the VOLTAGE SELECTOR to match the local power line. WARNING! – For optimal performance, use only the original power cable.
Preparations C Speakers Connection Front Speakers Connect the speaker wires to the SPEAKERS terminals, right speaker to "RIGHT" and left speaker to "LEFT", the wire (marked red) to "+" and the wire (marked black) to "-". Before using the remote control 1 Pull out the plastic protective sheet. 2 Select the source you wish to control by pressing one of the source select keys on the remote control (for example CD, TUNER). 3 Then select the desired function (for example É, í, ë).
Basic Functions Adjusting volume and sound 1 2 OP STANDBY-ON SOURCE BAND PROG/CLOCK - VOLUME E N / C LO S E + TUNING IMPORTANT: Before you operate the system, complete the preparation procedures. Switching the system on ● Press STANDBY-ON (y on the remote control). ➜ The system will switch to the last selected source. ● Press SOURCE (CD, TUNER or AUX on the remote control). ➜ The system will switch to the selected source. 3 4 Press VOLUME – / + to increase or decrease volume.
CD/MP3 Operation Basic playback controls To play a disc M I C R O S Y S T E M MCM108 ● Press 2; to start playback. ➜ The current track number and elapsed playing time of the track are displayed during disc playback. iR POP TRK PROG DBB MP3 To select a different track REP ALL ● Press ¡1 2™ once or repeatedly until the desired track number appears in the display. CD To find a passage within a track AUX-IN 1 Press and hold down on ¡1 2™. ➜ The disc is played at high speed and low volume.
CD/MP3 Operation 3 Press ¡1 2™ to select a desired track. Notes: – The SHUFFLE and REPEAT functions cannot be used simultaneously. – SHUFFLE play is not available in the programe mode. ➜ The album number will change accordingly as you reach the first track of an album by pressing ¡1 or the last track of an album by pressing 2™ . 4 Press 2; to start playback. Programming track numbers ● During playback, press once ALBUM 4 3 to show the current album number.
Radio Reception Other Connection Helpful hints: To improve radio reception: – For FM, extend coil antenna at the back of the unit fully for optimum reception. Listening to an external source You can listen to the sound of the connected external device through your system’s speakers. OP STANDBY-ON SOURCE BAND PROG/CLOCK - VOLUME 1 Select AUX source. 2 Use a line-in cable (not supplied) to connect E N / C LO S E + TUNING MCM 108’s AUX-IN jack (3.
Clock/Timer 4 5 Press ¡1 / 2™ to set the hours. 6 7 Press ¡1 / 2™ to set the minutes. M I C R O S Y S T E M M C M10 8 iR AUX-IN Press TIMER again. ➜ The clock digits for the minutes flash. Press TIMER to confirm the time. ➜ The timer is now set and actiated. Notes: : - If source CD is selected and no disc is in the CD tray or the disc has an error, TUNER will be selected automatically. - At the set time of wake up, the set will turn on at volume level 12.
Troubleshooting WARNING Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. Do not open the system as there is a risk of electric shock. If a fault occurs, first check the points listed below before taking the system for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre. Problem CD OPERATION “NO cd” is displayed. Solution – Insert a disc. – Check if the disc is inserted upside down.
Specifications AMPLIFIER Output power ........................................... 2 x 2W RMS .......................................................................... 200W PMPO Signal-to-noise ratio .......................... * 62 dBA (IEC) Frequency response ......... 60 – 16000 Hz, ± 3 dB Impedance loudspeakers ......................................... 8 1 Impedance headphones ................. 32 1 – 1000 1 CD PLAYER Frequency range ..................................
Meet Philips at the Internet http://www.philips.
