Micro Hi-Fi System pg001-018_MC108_05_Eng(general) 1 MC108 27/3/06, 13:11 xxxxx
Important notes for users in the U.K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: 1 2 Remove fuse cover and fuse. 3 Refit the fuse cover. Fix new fuse which should be a BS1362 3 Amp, A.S.T.A. or BSI approved type. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a value of 3 Amp.
4 1 5 2 OP E N / C LO S E 6 7 3 POWER BAND SOURCE PROG/CLOCK - VOLUME + TUNING MICRO SYSTEM MC108 8 iR 0 PROG TRK ! DBB MW FM AM PM MUTE SHUF TUNER CD REP ALL AUX @ # 9 AUX-IN 3 pg001-018_MC108_05_Eng(general) 3 27/3/06, 13:11
Contents English General Information Maintenance .............................................. 12 Environmental information ................................ 5 Supplied accessories ............................................ 5 Safety information ................................................ 5 Clock/Timer Preparation Rear connections ............................................. 6–7 Before using the remote control ...................... 7 Replacing battery (lithium CR2032) into the remote control ..
This product complies with the radio interference requirements of the European Community. Supplied accessories – 2 speaker boxes – remote control with battery – AM loop antenna Environmental Information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet).
Preparations English AM loop antenna FM wire antenna Speaker (left) Speaker (right) AC power cord Rear connections B Antennas Connection The type plate is located at the rear of the system. For users in the U.K.: please follow the instructions on page 2. 1 A Power AM (MW) antenna Unfold the loop antenna and if necessary, use screws (not supplied)to fix it to a flat, hard and stable place: 1 – Before connecting the AC power cord to the wall outlet, ensure that all other connections have been made.
English Preparations Before using the remote control C Speakers Connection Front Speakers Connect the speaker wires to the SPEAKERS terminals, right speaker to "RIGHT" and left speaker to "LEFT", coloured (marked) wire to "+" and black (unmarked) wire to "-". ● Fully insert the stripped portion of the speaker wire into the terminal as shown. Notes: – For optimal sound performance, use the supplied speakers. – Do not connect more than one speaker to any one pair of +/- speaker terminals.
Controls (illustrations on page 3) English Controls on the system and remote control 1 BAND – * DBB – (Dynamic Bass Boost) enhances the bass. $ MUTE – switches playback sound off and on. for Tuner (on the set only) selects waveband. 2 SOURCE (CD/ TUNER/ AUX) – – switches on the system. selects the respective sound source for CD/ FM/ MW/ AUX. 3 3 POWER / y – switches the system to standby/on. 4 PROG/CLOCK for CD ................. programs tracks and reviews the program. for clock ..............
English Basic Functions Adjusting volume and sound OP POWER SOURCE BAND PROG/CLOCK - VOLUME 1 Press VOLUME – / + to increase or decrease volume. ➜ Display shows the volume level and a number from 0-32. 2 Press DBB (on the remote control) to switch bass enhancement on or off. ➜ Display shows: DBB if the DBB is activated. E N / C LO S E + VOLUME DBB MUTE TUNING 3 IMPORTANT: Before you operate the system, complete the preparation procedures.
CD Operation English 5 To pause playback press 2;. Press 2; again to resume play. ➜ The display freezes and the current track number flashes when playback is paused. 6 To stop disc playback, press 9. MICRO SYSTEM MC108 iR PROG TRK Note: CD play will also stop when; – the CD door is opened. – the disc has reached the end. – you select another source: AUX, TUNER. – you select standby. DBB REP ALL CD Selecting a different track AUX-IN IMPORTANT: The lens of the CD player should never be touched.
Programming track numbers Different play modes: SHUFFLE and REPEAT Programme in the STOP position to select and store your disc tracks in the desired sequence. If you like, store any track more than once. Up to 20 tracks can be stored in the memory. You can select and change the various play modes before or during playback. REPEAT ............ plays the current track continuously REPEAT ALL ... repeats the entire disc/ programme SHUFFLE .........
Radio Reception English 3 Turn TUNING 0 to tune to a station. ➜ Display shows: the frequency of the tuned station. Helpful hints: To improve radio reception: – For FM, extend coil antenna at the back of the unit fully for optimum reception. OP POWER SOURCE BAND PROG/CLOCK - VOLUME E N / C LO S E + TUNING Tuning to radio stations 1 Select TUNER source. ➜ 2 TUNER is displayed. Press BAND (TUNER on the remote control) once or more to select your waveband.
Setting the timer ● The system can be used as an alarm clock. CD or TUNER can be set to switch on at a preset time. The clock time needs to be set first before the timer can be used. ● If no button is pressed within 90 seconds during timer setup, the system will exit timer setting mode automatically. MICRO SYSTEM MC108 iR 1 In any mode, press TIMER (on the remote control) for more than 2 seconds. 2 Press ¡1 / 2™ (or CD / TUNER on the remote control) to select sound source.
Clock/Timer English Activating and deactivating SLEEP The sleep timer enables the system to switch off by itself after a set period of time. The clock time needs to be set first before the sleep timer can be used. ● Press SLEEP on the remote control repeatly to select desired time before system shuts off.
WARNING Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. Do not open the system as there is a risk of electric shock. If a fault occurs, first check the points listed below before taking the system for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre. Problem Solution CD OPERATION “no cd” is displayed. – Insert a disc. – Check if the disc is inserted upside down.
English 16 16 pg001-018_MC108_05_Eng(general) 16 27/3/06, 13:11 MC-320/22-1
English 17 pg001-018_MC108_05_Eng(general) 17 27/3/06, 13:11 xxxxx
Meet Philips at the Internet http://www.philips.
