Micro Hi-Fi System 220 MC- 1 3140 115 30101
México Es necesario que lea cuidadosamente su instructivo de manejo. PRECAUCIÓN - ADVERTENCIA No abrir, riesgo de choque eléctrico ATENCIÓN Verifique que el voltaje de alimentación sea el requerido para su aparato Para evitar el riesgo de choque eléctrico, no quite la tapa. En caso de requerir servicio, dirijase al personal calificado. Microsistema de Audio MC-220/ 21 110–127 / 220–240V; ~50–60 Hz 26 W Philips Mexicana, S.A. de C.V. Av. La Palma No.6 Col.
% ! 2 CD 0 ^ & REPEAT TUNER TAPE SHUFFLE AUX SLEEP ) 5 VOL 9 6 * DSC DBB MUTE IS NEWS/TA ( $ # @ ! STANDBY-ON PROGRAM TIMER PROGRAM SHUFFLE 0 9 8 3 PREV PLAY•PAUSE NEXT REPEAT SHUFFLE SIDE A/B 4 SOURCE SELECT RECORD CLOCK REV MODE BAND ON OFF 1 2 3 STOP iR 5 6 7 3 3140 115 30101
3140 115 30101
English Index Français English ------------------------------------------------ 6 Español Français -------------------------------------------- 22 Español --------------------------------------------- 38 -------------------------------------------------------- 54 5 3140 115 30101
Contents English General Information Clock/Timer Environmental information ................................ 7 Supplied accessories ............................................ 7 Safety information ................................................ 7 Setting the clock ................................................. 18 Setting the timer ................................................. 18 Activating and deactivating TIMER ................. 18 Activating and deactivating SLEEP ..................
Environmental Information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet). Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.
Preparations English AM loop antenna FM wire antenna speakers (right) AM aerial B C speakers (left) A AC power cord Rear connections The type plate is located at the rear of the system. A Power B Antennas Connection Connect the supplied AM loop antenna and FM antenna to the respective terminals. Adjust the position of the antenna for optimal reception.
Preparations FM Antenna English Optional connection The optional equipment and connecting cords are not supplied. Refer to the operating instructions of the connected equipment for details. ● For better FM stereo reception, connect an outdoor FM antenna to the FM AERIAL (FM ANTENNA) terminal. C Speakers Connection Front Speakers Connect the speaker wires to the SPEAKERS terminals, right speaker to "RIGHT" and left speaker to "LEFT", coloured (marked) wire to "+" and black (unmarked) wire to "-".
Controls (illustrations on page 3) English Controls on the system and remote control 1 CLOCK 2 3 4 – 5 – – 6 7 – 8 – 9 for Clock ............ sets the clock function. for Tape ............... shows tape counter in recording mode. REPEAT/ REV MODE/ BAND for CD ................. repeats a track/CD programme/ entire CD. for Tape ............... selects tape reverse modes. for Tuner ............. selects waveband. SHUFFLE/ SIDE A/B for CD ................. plays CD tracks in random order. for Tape ....
Adjusting volume and sound STANDBY-ON PROGRAM TIMER CLOCK REPEAT REV MODE BAND ON OFF 1 Turn the VOLUME control anti-clockwise to decrease or clockwise to increase volume on the system (or press VOL -/+ on the remote control). ➜ Display shows the volume level VOL and a number from 0-32. 2 Press DSC repeatedly to select the desired sound effect: OPTIMAL (no indication)/ ROCK ( ) / JAZZ ( ) / POP ( ). 3 Press DBB to switch bass enhancement on or off. ➜ Display shows: DBB if the DBB is activated.
CD Operation English STANDBY-ON PROGRAM TIMER CLOCK REPEAT REV MODE BAND ON OFF PREV PLAY•PAUSE To interrupt playback press PLAY•PAUSE 2; (on the remote control 2;). Press PLAY•PAUSE 2; (on the remote control 2;) again to resume play. ➜ The display freezes and the elapsed playing time flashes when playback is interrupted. 6 To stop disc playback, press STOP 9. SHUFFLE SIDE A/B SOURCE SELECT RECORD 5 Note: CD play will also stop when; – the CD door is opened. – the disc has reached the end.
Programming track numbers Different play modes: SHUFFLE and REPEAT You can select and change the various play modes before or during playback. The play modes can also be combined with PROGRAMME. 1 Press PROGRAM to enter the programming mode. ➜ A track number is shown and PROGRAM flashes. 2 Use the PREV ¡1 or NEXT 2™ (on the remote control ¡ or ™) to select your desired track number.
Radio Reception English Programming radio stations You can store up to a total of 40 radio stations in the memory. STANDBY-ON PROGRAM TIMER CLOCK REPEAT REV MODE BAND ON OFF SHUFFLE Automatic programming Automatic programming will start with a chosen preset number. From this preset number upwards, former programmed radio stations will be overridden. The system will only programme stations which are not in the memory already.
Radio Reception English Tuning to preset radio stations ● Press PRESET 3 or 4 (on the remote control ¡ or ™ ) until the desired preset station is displayed. Changing tuning grid (some versions only) In North and South America the frequency step between adjacent channels in the AM and FM band are 10 KHz and 100 KHz respectively. In the rest of the world this step is 9 KHz and 50 KHz. Usually the frequency step has been preset in the factory for your area if not: 1 2 Select TUNER source.
Tape Operation / Recording English Switching tape sides The tape side can be switched manually or automatically before or during tape playback. STANDBY-ON PROGRAM TIMER CLOCK SHUFFLE REPEAT REV MODE BAND ON OFF SIDE A/B ● Press SIDE A/B (during playback only 2; on the remote control). ➜ The display shows SIDE A or SIDE B and the tape counter resets to 000. SOURCE SELECT Reverse mode options RECORD PREV PLAY•PAUSE NEXT STOP iR Tape playback 1 Select TAPE source.
Synchro start CD recording Recording timer 1 2 Select CD source. To record from the radio, you will need to use a preset radio station and to set a start (ON) and finish (OFF) time. 3 4 Press OPEN to open the tape door. Insert a disc and if desired, programme track numbers. Insert a suitable tape into the deck and close the tape door. 5 Press RECORD to start recording. ➜ COPY or RECORD is displayed briefly and RECORD is shown during recording.
Clock/Timer English STANDBY-ON PROGRAM TIMER CLOCK REPEAT REV MODE BAND ON OFF 3 Press TIMER ON•OFF to confirm your desired mode. ➜ The selected source CD or TUNER is shown. Display sequence scrolls SET ON TIME and TIMER flashes. The clock digits for the hours flash. 4 Turn VOLUME to set the hours: clockwise for hours up; anti-clockwise for hours down. 5 Press TIMER ON•OFF again. ➜ The clock digits for the minutes flash.
AMPLIFIER Output power ....................................... 2 x 10 W RMS ......................................................................... 400 W PMPO Signal-to-noise ratio .......................... ≥ 65 dBA (IEC) Frequency response ......... 40 – 20000 Hz, ± 3 dB Input sensitivity AUX ....................... 0.5 V (max. 2 V) Impedance loudspeakers ......................................... 8 Ω Impedance headphones .................... 32 Ω -1000 Ω CD PLAYER Frequency range .......................
Troubleshooting English WARNING Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. Do not open the system as there is a risk of electric shock. If a fault occurs, first check the points listed below before taking the system for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre. Problem CD OPERATION “NO DISC” is displayed. RADIO RECEPTION Radio reception is poor.
The remote control does not function properly. The timer is not working. The Clock/Timer setting is erased. – Select the source (CD or TUNER, for example) before pressing the function button (É,í,ë). – Reduce the distance between the remote control and the system. – Insert the batteries with their polarities (+/– signs) aligned as indicated. – Replace the batteries. – Point the remote control directly toward IR sensor on the front of the system. – Set the clock correctly.
