Register your product and get support at HSB2313/12 www.philips.
1 Important 4 4 4 Safety Notice 2 Your home theater system Attach speakers to the main unit Attach the stand Connect AV devices Connect power Prepare the remote control Turn on Set clock Enable Easylink 4 Play Play from USB Play connected AV devices 23 9 Appendix 24 24 Mount to a wall 7 7 7 8 9 Introduction What’s in the box Overview of the main unit Overview of the remote control 3 Get started 8 Troubleshooting 11 11 11 12 15 16 16 17 17 18 18 18 5 Adjust volume level and sound effect 19 Adj
1 Important Know these safety symbols Safety • • • • • • • • • • • • 4 Read and understand all instructions before you use the apparatus. If damage is caused by failure to follow instructions, the warranty does not apply. Never insert objects into the ventilation slots or other openings on the apparatus. Never remove the casing of this apparatus. Place the apparatus on a flat, hard and stable surface.
Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories. Other trademarks and trade names are those of their respective owners. This apparatus includes this label: Note • The type plate is located on the back of the apparatus.
E n g lis h 2 Your home theater system Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.Philips.com/welcome. Introduction With the home theater system, you can • Get superb sound performance when you watch TV, DVDs, listen to music, or play games. • Enjoy MP3/WMA music directly from your portable USB device.
Overview of the main unit a c b d ef g h i OPTICAL HDMI IN 1 j k l m n o a SOUND SETTINGS (GAMES, MOVIE, MUSIC) • Select a sound effect. HDMI IN 2 pq r HDMI OUT s t b IR sensor e POWER • Turn on the unit, switch it to standby mode, or switch it to Eco Power Standby. c Display panel • Show current status. f USB DIRECT • Socket for a USB mass storage device. d AV FRONT / MP3 LINK • AV input socket on the front panel. • Jack for an external audio device.
j PRESS • Detach speakers from the main unit. Overview of the remote control E n g lis h i SOURCE • Select a source. k DC IN • Power supply socket. a l SUBWOOFER OUT • Subwoofer out socket. b m DIGITAL IN - OPTICAL • Optical audio input socket. c y n DIGITAL IN - COAXIAL • Coaxial audio input socket. o VIDEO OUT • Socket for composite video output. d p HDMI IN 1 • HDMI input socket. q AV1 IN (VIDEO,AUDIO L/R) • AV input sockets. r HDMI IN 2 • HDMI input socket. s HDMI OUT • HDMI output socket.
b HDMI • Select an HDMI audio input source. p MUTE • Mutes volume. c OPT • Select Optical audio input source.. q TIMER • Set the alarm timer. d Navigation buttons • ALB/PRESET/ Skip to the previous/next album (folder) in the USB device • / , / Fast reverse or fast forward within a track in the USB device. • Start or pause USB play. r PROGRAM • Program tracks in a USB device. e COAX • Select Coaxial audio input source. f / • Skip to the previous/next track in the USB device. g VOL +/• Adjust volume.
E n g lis h 3 Get started Caution • Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. Always follow the instructions in this chapter in sequence. If you contact Philips, you will be asked for the model and serial number of this apparatus. The model number and serial number are on the back of the apparatus. Write the numbers here: Model No. __________________________ Serial No.
Tip • You can also mount the apparatus on a wall. OPTICAL HDMI IN 1 HDMI IN 2 HDMI OUT Not used Connect AV devices Note • The type of devices and connections in the following • L instructions are for reference only. When you connect cables, ensure that the color of the plug matches the color of the socket. AUDIO OUT If you connect the home theater system to your TV, you can enjoy the superb sound performance while watching TV.
If your TV connected to a set-topbox (to convert analog signal into digital signal), connect the supplied AV cable to AV output sockets on the set-top-box and the AV1 IN or AV2 IN sockets. E n g lis h • Connect DVD player If you connect your DVD player and TV to the home theater system, you can enjoy superb sound performance during watching DVD movie. a Connect the system to the TV.
• You can connect the AV output sockets on a game console to the AV1 IN or AV2 IN sockets on the system. OPTICAL HDMI IN 1 HDMI IN 2 HDMI OUT Connect HDMI supported devices HDMI (High Definition Muiltimedia Interface) is a digital interface that supports both audio and video transmission through a single cable. If you connect your HDMI-compliant DVD players and TV to the home theater system, you can watch DVDs or Blu-ray discs that contain HD (High-Definition) content.
Press HDMIto select HDMI 1 or HDMI 2. Connect coax supported devices Tip E n g lis h 3 • You can connect all the devices to the home theater system at the same time. The home theater system can decode digital audio signal. You can connect the system to your digital amplifier or receiver. Connect power Caution OPTICAL HDMI IN 1 HDMI IN 2 HDMI OUT • Risk of product damage! Ensure that the power supply • Amplifier voltage corresponds to the voltage printed on the back or the underside of the product.
Prepare the remote control Caution • Risk of explosion! Keep batteries away from heat, sunshine or fire. Never discard batteries in fire. • Risk of decreased battery life! Never mix different brands or types of batteries. • Risk of product damage! When the remote control is not used for long periods, remove the batteries. Note • Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. 1 2 OPTICAL HDMI IN 1 2 HDMI IN 2 HDMI OUT 3 Open the battery compartment.
Press for over 3 seconds. » The backlight on the display panel turns off. E n g lis h 1 » The blue Eco Power indicator lights up. Set clock 1 In the standby mode, press and hold CLOCK to enter the clock setting mode. » Clock is displayed and the hour digits begin to blink. 2 3 Press + VOL - to set the hour. 4 5 Press CLOCK to confirm » The minute digits begin to blink. Press + VOL - to set the minute. Press CLOCK to confirm the clock setting.
2 4 Play Play from USB Random play Note • Ensure that the USB device contains playable music. (see ‘USB playability information’ on page 23) 1 2 To return to normal play, press REPEAT until the selected function is no longer displayed. 1 Press SHUF. » All tracks are played randomly. 2 To return to normal play, press SHUF again. Tip Flip open the cover on the front panel. Insert the USB plug of a USB device into the socket. • The repeat and shuffle functions cannot be activated at the same time.
• Select equalizer settings 1 Adjust volume level 1 [NORMAL] (normal) During play, press VOL +/- to increase/ decrease the volume level. During USB play, press MUSIC SOUND repeatedly to select: • [POP] (pop) • [JAZZ] (jazz) • [ROCK] (rock) • [CLASSIC] (classic) • [NORMAL] (normal) Adjust subwoofer volume Mute sound 1 1 Press SUBW.VOL to adjust the subwoofer volume. Select a sound effect Note • You cannot use different sound effects at the same time.
6 Use more of your home theater system Set timer The home theater system can turn on automatically at a set time. 1 Ensure that you have set the clock correctly. 2 In standby mode, press and hold TIMER. » The TIMER is displayed and hour digits begin to blink. 3 4 Press + VOL - to set the hour. 5 6 7 Press TIMER to confirm. » The minute digits begin to blink. Press + VOL - to set the minute. Press TIMER to confirm. » The mode indicator begins to blink. Press + VOL - to select [ON] (on).
Note • Product information is subject to change without prior notice. Product information General information AC power 220 - 230V, 50Hz 70W Operation Power Consumption Standby Power Consumption <10W Eco Standby Power <1W Consumption USB Direct Full Speed Ver1.1 Dimensions (W x H x D) 800 x 90 x Main unit and speakers 95mm 180 x 330 x Subwoofer 340mm Weight With Packing 9.5 kg Main unit and speakers 1.8 Kg Subwoofer 5.
• • • • • • • • • • • • 22 EN USB or memory file format FAT12, FAT16, FAT32 (sector size: 512 bytes) MP3 bit rate (data rate): 32-320 Kbps and variable bit rate WMA v9 or earlier Directory nesting up to a maximum of 8 levels Number of albums/ folders: maximum 99 Number of tracks/titles: maximum 999 File name in Unicode UTF8 (maximum length: 128 bytes) Unsupported formats: Empty albums: an empty album is an album that does not contain MP3/ WMA files, and is not be shown in the display.
Warning • Never remove the casing of this apparatus. To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this apparatus, check the following points before requesting service. If the problem remains unsolved, go to the Philips web site www. philips.com/welcome. When you contact Philips, ensure that the apparatus is nearby and the model number and serial number are available. No power • Ensure that the AC adaptor of the main unit is connected properly.
9 Appendix Mount the main unit and speakers Caution Mount to a wall • To find a suitable mounting location, make the necessary physical and wireless connections. • Mount the main unit and speakers to a solid concrete wall or plaster board wall only! Caution • Risk of product damage! Always consult professional • personnel to safely mount the product to a wall. Risk of injury! Ensure that no supply ducts such as gas, water or electricity are harmed when you drill the holes.
E n g lis h 4 Secure the wall mount bracket onto the main unit with 2 supplied screws. 5 Hook the main unit and speakers in place.
© 2009 Koninklijke Philips Electronics N.V. All rights reserved.
