LU UST_EN_US.book Page 1 Mardi, 18. mars 2014 1:31 13 Register your product and get support at Screeneo www.philips.
LU UST_EN_US.book Page 2 Mardi, 18. mars 2014 1:31 13 Table of Contents Overview ................................................... 3 8 Media Playback .................................. 23 Dear Customer ................................................................... About this User Manual ..................................................... What's in the Box ............................................................... Product Highlights ...........................................................
LU UST_EN_US.book Page 3 Mardi, 18. mars 2014 1:31 13 Overview Dear Customer What's in the Box Thank you for purchasing our projector.
LU UST_EN_US.book Page 4 Mardi, 18. mars 2014 1:31 13 1 General Safety Information Do not make any changes or settings that are not described in this user manual. Physical injury or damage to the device or loss of data can result from improper handling. Take note of all warning and safety notes indicated. Do not expose the device to extreme vibrations. It may damage the internal components. Do not allow children to handle the device without supervision.
LU UST_EN_US.book Page 5 Mardi, 18. mars 2014 1:31 13 Power Supply Before turning on your device, check that the outlet that you are going to plug it into conforms to the indications shown on the information plate (voltage, current, power network frequency) located on your device. This device shall be connected to a single phase power network. The device shall not be installed on bare ground. Only use the power cable that is supplied with your device. Your device is delivered with a grounded power cord.
LU UST_EN_US.book Page 6 Mardi, 18.
LU UST_EN_US.book Page 7 Mardi, 18. mars 2014 1:31 13 3 EPG –To display the electronic program guide. 3D – To display the 3D menu. Favorite – To display the favourite list in DVB-T mode. Remote Control a b c 4 To display the home menu. 5 TAB key or Toggle between TV and Radio channels in DVB-T mode and browsing the Internet without external keyboard.
LU UST_EN_US.book Page 8 Mardi, 18. mars 2014 1:31 13 Browsing the user interface Navigation for setting menu Navigation can be done by navigation keys ( , , À,Á, OK and ¿) on the control panel or the remote control, as well as by an air mouse. Navigation by keys: • / scrolls trough the menu level up and down. • OK/Á goes one level down, with À / ¿ one level up. • u goes back to the main screen. • In the final level, accepts a setting and goes back to the last sub menu.
LU UST_EN_US.book Page 9 Mardi, 18.
LU UST_EN_US.book Page 10 Mardi, 18. mars 2014 1:31 13 3 Initial Operation Setting up the Device Before installing your device, make sure that the projector is turned off and the power cord is unplugged from the power outlet. You can position the device so that it lies flat on a table in front of the projection surface; it is not necessary to tilt it towards the projection surface. The device compensates for the distortion from the slanted projection (pincushion distortion).
LU UST_EN_US.book Page 11 Mardi, 18. mars 2014 1:31 13 3 Push the battery compartment back into the remote control until the locking mechanism engages. Notice Normally the batteries will last for around one year. If the remote control stops working, please replace the batteries. If the device is not used for a long time, take out the batteries. This will prevent leakage and possible damage to the remote control.
LU UST_EN_US.book Page 12 Mardi, 18. mars 2014 1:31 13 Initial Installation ECO mode 1 Push the POWER B button for 5 seconds till the power indicator turns to red to turn the device on. 2 Turn the device towards a suitable projection surface or wall. Note that the distance to the projection surface must be a minimum of 0.1 meter and a maximum of 0.5 meter (see Setting up the Device, page 4). Make sure the projector is in a secure position.
LU UST_EN_US.book Page 13 Mardi, 18. mars 2014 1:31 13 4 Connect to the Playback Device HDMI cable Connecting to a Computer (VGA) Connecting to Devices with HDMI Output Notice Supplied cables Many laptops do not activate the external video output automatically when you connect a second display such as a projector. Check your laptop's manual to find out how to activate the external video output. Use the HDMI cable to connect the projector to a computer, laptop or others devices.
LU UST_EN_US.book Page 14 Mardi, 18. mars 2014 1:31 13 Connecting Using an Audio/ Video (CVBS) Adapter Cable Use the projector's audio/video adapter cable (A/V cable) (not included) to connect camcorders, DVD players or digital cameras. The jacks for these devices are yellow (video), red (audio right) and white (audio left). Connecting to a home cinema amplifier Use a S/PDIF optical cable (cable not provided) to connect the DIGITAL AUDIO output on the projector to the input of your home cinema amplifier.
LU UST_EN_US.book Page 15 Mardi, 18. mars 2014 1:31 13 Connecting the headphones 1 Before connecting the headphones, turn down the volume on the device. 2 Connect the headphones to the projector's headphone slot. The device speakers deactivate automatically when the headphones are connected. 7 Connect the external device (smartphone or tablet) to the same WiFi network that the projector.
LU UST_EN_US.book Page 16 Mardi, 18. mars 2014 1:31 13 5 Memory Inserting a Memory Card Connecting USB Storage Medium PHILIP S PHILIP S 1 Insert a memory card with the contacts facing upwards into the / slot at the back of the device. Your device supports the following memory cards: SD/SDHC/SDXC/MMC. 2 Insert the memory card into the slot until it snaps into position. DANGER! Inserting a Memory Card! Never pull out the memory card while the device is accessing it.
LU UST_EN_US.book Page 17 Mardi, 18. mars 2014 1:31 13 6 Network The projector can be connected to the network by a network hard-wired cable or through a wireless (Wi-Fi) connection. Use the procedure below appropriate to the type of connection you want. LAN Network Notice Connection! The LAN connection takes priority over the Wi-Fi connection. Connecting to the LAN network 1 Connect one end of a LAN cable (not supplied) to the ETHERNET port of your projector.
LU UST_EN_US.book Page 18 Mardi, 18. mars 2014 1:31 13 DANGER! Information on Using WLAN! The functioning of security systems, medical equipment or sensitive devices can be disrupted by the transmission power of the device. Observe any usage regulations (or restrictions) in the vicinity of such equipment. The use of this device can affect the operation of insufficiently shielded medical devices and hearing aids and pacemakers through the release of high frequency radiation.
LU UST_EN_US.book Page 19 Mardi, 18. mars 2014 1:31 13 Using WPS with Push Button Configuration (PBC) Wifi Hotspot Notice 1 Switch the device on using the on/off key. 2 After the initial screen the main menu appears. Important! The projector can work as an access point, if only a wired lan network is installed in the location of use. Use the portable Wi-Fi hotspot to share the device’s network connection with computers or other devices through the Wi-Fi network.
LU UST_EN_US.book Page 20 Mardi, 18. mars 2014 1:31 13 Setting up a WiFI hotspot To modify the WiFi hotspot name and define the security level. 1 Switch the device on using the on/off key. 2 After the initial screen the main menu appears. 3 Use the navigation keys to select Settings. Digital Living Network Alliance (DLNA) This device supports Digital Living Network Alliance (DLNA). Using this standard you can quickly interconnect your multimedia devices.
LU UST_EN_US.book Page 21 Mardi, 18. mars 2014 1:31 13 7 Bluetooth Activating the Bluetooth connection 1 Switch the device on using the on/off key. 2 After the initial screen, the main menu appears. 8 Confirm with . 9 Using / select the desired setting. 10 Confirm with . 11 Modify the desired settings. Menu Description Select device The list shows all paired devices. Paired device To unconnect or unpair the paired device. Bluetooth speaker 3 Use the navigation keys to select Settings.
LU UST_EN_US.book Page 22 Mardi, 18. mars 2014 1:31 13 5 Press the Red key to power on the speaker. 6 Press the Green key to make the speaker discoverable during 60 seconds. 7 On your external device, activate the Bluetooth connection and select the speaker name from the list. When the device is connected, his name is displayed on the top of the screen. 8 Press the Green key to play music. During music playback, the following actions are available: Red key: To stop the connection.
LU UST_EN_US.book Page 23 Mardi, 18. mars 2014 1:31 13 8 Media Playback Notice Navigation Keys All the keys shown are buttons on the remote control. Keys Action Green key of the remote control Allows to set the slide show parameters for picture files. or Allows to set the shuffle mode for music files: Notice Best Settings for Optimal Use Read the informations on the best settings in the chapter settings (see Settings, page 31) for optimal use of your device.
LU UST_EN_US.book Page 24 Mardi, 18. mars 2014 1:31 13 Video playback Notice Displaying Video Files Only those videos that are compatible with the projector will be displayed. Supported file formats Supported file formats are *.avi, *.mov, *.mp4, *.mkv, *.flv, *.ts, *.m2ts, *.3gp. Video Playback (USB/SD Card/ Internal Memory/DLNA) 1 Switch the device on using the on/off key. 2 The main menu appears. 8 Press or Á to start playback. 9 Press ¿ to end the slide show and return to the overview.
LU UST_EN_US.book Page 25 Mardi, 18. mars 2014 1:31 13 5 To only display the picture content, select Picture using the keys / on the left of the screen and confirm with . Slide Show with Background Sound Notice 1 During the slide show, press to display the menu bar on the bottom of the screen. 2 Using À/Á select Ó. 3 Confirm with . 4 Use / to select the file that you wish to play. The use of color keys The Green key allows to set the slide show parameters.
LU UST_EN_US.book Page 26 Mardi, 18. mars 2014 1:31 13 Music Playback Notice Switch off the Image Playback You can switch off the screen while playing music in order to save power by a long press on the 5 To only display the music content, select Music using the keys / on the left of the screen and confirm with . Notice The use of color keys The Red key allows to set the repeat mode: key. Supported file formats Supported file formats are MP3 and WAV.
LU UST_EN_US.book Page 27 Mardi, 18. mars 2014 1:31 13 Managing Files Delete Files You can delete files from the internal memory, the connected USB storage medium or the memory card. 1 Switch the device on using the on/off key. 2 The main menu appears. 3 Use the navigation keys to select the desired media (USB, Memory or DLNA). 4 Confirm with . 5 Use / to select the file that you want to delete. 6 Press the Blue key on the remote control to delete the file. 7 Confirm with .
LU UST_EN_US.book Page 28 Mardi, 18. mars 2014 1:31 13 9 Digital TV Playback (Depending on model) First Playback Connecting the Aerial Notice Navigation Keys All the keys shown are buttons on the remote control. Notice Aerial Size and Orientation In some regions it is necessary to connect a larger aerial in order to grant the reception. In some countries it is necessary to point the aerial horizontally in order to grant the reception.
LU UST_EN_US.book Page 29 Mardi, 18. mars 2014 1:31 13 1 Switch the device on using the on/off key. 2 The main menu appears. 3 Use the navigation keys to select TV. 4 Confirm with OK. 5 The last viewed channel is played. Change the channel using keys CH+/CH-, / or enter directly the number with the keypad. Notice Displaying Channel Information When changing channel, channel information is displayed on the bottom projection edge. The information bar is hidden after 5 seconds.
LU UST_EN_US.book Page 30 Mardi, 18. mars 2014 1:31 13 10 Android Your projector uses the Android operating system. Starting Android Apps 1 Switch the device on using the on/off key. 2 After the initial screen the main menu appears. 7 Use the navigation keys to select ApkInstaller. 8 Confirm with OK. 9 Use the navigation keys to select Install. 10 Confirm with OK. 11 Navigate to the memory card and select the APK package you want to install. 12 Press OK to execute the installation package.
LU UST_EN_US.book Page 31 Mardi, 18. mars 2014 1:31 13 11 Settings 1 Switch the device on using the on/off key. 2 After the initial screen the main menu appears. 3 Use the navigation keys to select Settings. 4 Confirm with OK. 5 Use / to select from the following settings. 6 Confirm with OK. 7 Modify the settings using OK, / , 8 Confirm with OK. The ¿ key takes you one step back in the menu. Overview of the Menu Functions Wireless and Network WiFi – switching the wireless network (WLAN) off and on.
LU UST_EN_US.book Page 32 Mardi, 18. mars 2014 1:31 13 When the parameter is switched on, it works like this: - If the projector is on, while no video is displayed (e.g. menu open without user action), it should go into off mode after the shortest possible time, by example 30 minutes. - If a video is displayed, the APD should take place 3h after last user action, meaning that a pop-up will appear after 2h58 for 2 minutes, indicating that the product will go into off mode.
LU UST_EN_US.book Page 33 Mardi, 18. mars 2014 1:31 13 12 Service Cleaning DANGER! Instructions for Cleaning! Use a soft, lint-free cloth. Never use liquid or easily flammable cleansers (sprays, abrasives, polishes, alcohol, etc.). Do not allow any moisture to reach the interior of the device. Do not spray the device with any cleaning fluids. Wipe over the surfaces gently. Be careful that you do not scratch the surfaces. Cleaning the Lens 12 The device turns off and on again.
LU UST_EN_US.book Page 34 Mardi, 18. mars 2014 1:31 13 Troubleshooting 1 Switch the device off using the on/off key on the panel control. 2 Wait at least ten seconds. 3 Switch the device on using the on/off key on the panel control. 4 If the problem repeats, please contact our technical customer service or your retailer. Power Cycling If a problem occurs that cannot be corrected with the instructions in this user manual (see also the help below), follow the steps given here.
LU UST_EN_US.book Page 35 Mardi, 18. mars 2014 1:31 13 Problems Solutions The device turns itself off • • • The device changes from maximum level of brightness to • minimum level of brightness when the device is connected over USB to play videos. • The device cannot connect with an Android device (for example a mobile phone/smartphone with the Android operating system) when connected via USB.
LU UST_EN_US.book Page 36 Mardi, 18. mars 2014 1:31 13 13 Appendix Technical Data Accessories Dimensions (L×H×W) .................... 287 × 148× 339 mm Weight ........................................................................... 5,3 kg Recommended Ambient......................................5 – 35 ºC Relative Humidity ................15 – 85 % (non-condensing) File format................................ *.avi, *.mov, *.mp4,*.mkv, ................................................ *.flv, *.ts, *.
LU UST_EN_US.book Page 37 Mardi, 18. mars 2014 1:31 13 Batteries: If your product contains batteries, they must be disposed of at an appropriate collection point. The CE marking certifies that the product meets the main requirements of the European Parliament and Council directives 1999/5/CE, 2006/95/CE, 2004/108/ CE and 2009/125/CE on information technology equipment, regarding safety and health of users and regarding electromagnetic interference.
LU UST_EN_US.book Page 38 Mardi, 18. mars 2014 1:31 13 PHILIPS and the PHILIPS’ Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used by Sagemcom Documents SAS under license from Koninklijke Philips N.V. © 2014 Sagemcom Documents SAS All rights reserved Sagemcom Documents SAS Documents Business Unit Headquarters : 250, route de l’Empereur 92848 Rueil-Malmaison Cedex · FRANCE Tel: +33 (0)1 57 61 10 00 · Fax: +33 (0)1 57 61 10 01 www.sagemcom.
