Register your product and get support at 02 English www.philips.com/welcome Type HD8833 SUP 037R 02 EN OPERATING INSTRUCTIONS READ THESE OPERATING INSTRUCTIONS CAREFULLY BEFORE USING THE MACHIN MACHINE.
IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. 2. Do not touch hot surfaces. Use handles or knobs. 3. To protect against fire, electric shock and injury to persons do not immerse cord, plugs, or appliance in water or other liquid. 4. Close supervision is necessary when the appliance is used by or near children. 5. Unplug from outlet when not in use and before cleaning.
CAUTION This appliance is for household use only. Any servicing, other than cleaning and user maintenance, should be performed by an authorized service center. Do not immerse machine in water. To reduce the risk of fire or electric shock, do not disassemble the machine. There are no parts inside the machine serviceable by the user. Repair should be done by authorized service personnel only. 1. Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage. 2.
GENERAL INFORMATION The coffee machine is suitable for preparing espresso coffee using either coffee beans or ground coffee and is equipped with a device to dispense steam and hot water. The structure of the machine has been designed for domestic use only and is not suitable for continuous professionaltype operation. Keep these operating instructions in a safe place and make them available to anyone who may use the coffee machine.
Danger of Burns Never direct the steam/hot water wand towards yourself or others: Danger of scalding! Always use the handles or knobs provided. Machine Location - Suitable Location for Operation and Maintenance For best use, it is recommended to: • Choose a safe, level surface, where there will be no danger of overturning it or being injured. • Choose a location that is sufficiently well-lit, clean and near an easily reachable socket.
Grinder adjustment knob Coffee bean hopper cover Coffee bean hopper Control panel Dispensing spout Pre-ground coffee compartment Cup holder grill Full drip tray indicator Brew group Service door Coffee grounds drawer Wand protective gripper Hot water/steam wand ON-OFF power button Drip tray Water tank Grease for the brew group Pre-ground coffee scoop Power cord LED display Intenza Water Filter (Optional) “Aroma” - Pre-ground coffee selector switch Long coffee light button Espresso coffee ligh
INSTALLATION • Remove the water tank from its seat. For your safety and the safety of others, carefully follow the instructions provided in the “Safety Regulations” section. • Rinse and fill it with fresh water making sure that it is not filled exceeding the MAX level indicated in the water tank. Put the water tank back in its seat. Machine Packaging The original packaging has been designed and constructed to protect the machine during transport.
• Switch the power button to “I” to turn the machine on. Circuit Priming • The “STAND-BY” button blinks. • Turn the selector dial clockwise to set it to the“ ” position. The machine starts the automatic priming of the circuit by letting out a preset quantity of water through the Pannarello. • To prime the water circuit, place a container under the steam wand (Pannarello, if supplied). • Make sure the selector dial is in the “ ” position; if this is not the case, set it to that position.
Using the machine for the first time or after a long period of inactivity. These simple operations will make it possible to always brew excellent coffee. Steady on 10 At the end, fill the water tank again. Then the products can be brewed as described in the following sections. 1 Place a large container under the dispensing spout. Steady on 9 Dispense water until the no water signal is displayed, then turn the selector dial counter-clockwise to set it to the “ ” position.
“INTENZA” water filter (optional) To improve the quality of the used water, it is advisable to install the water filter. Remove the water filter from its packaging, immerse it vertically (with the opening positioned upwards) in cold water and delicately press the sides so as to let the air bubbles out. Remove the small white filter from the tank and store it in a dry place sheltered from dust. Set the Intenza Aroma System as specified on the box.
The machine allows slight adjustments to the coffee grinder to adapt it to the kind of coffee used. At this point the button “ ” is programmed; each time it is pressed and released, the machine will brew the same amount of coffee that was just programmed. To make any adjustment, press and turn the knob inside the coffee bean hopper. Stand-by Press and turn the knob by one notch at a time and brew 2-3 cups of coffee; this is the only way to notice differences in grind.
Selection must be made prior to selecting the coffee. The system sets the aroma according to the personal taste of the user. Dispensing Spout Adjustment Most cups on the market can be used with this coffee machine. The height of the dispensing spout may be adjusted to better fit the dimensions of the cups that you wish to use. Steady on Manually move the dispensing spout up or down to adjust its height by placing your fingers as shown in the figure.
This function allows using pre-ground and decaffeinated coffee. • Coffee brewing stops automatically when the pre-programmed level is reached; however, it is possible to interrupt coffee brewing by pressing the button initially pressed. Pre-ground coffee must be poured into the appropriate compartment positioned next to the coffee bean hopper. Only use ground coffee for espresso machines and never coffee beans or instant coffee.
• Turn the selector dial clockwise to set it to the “ ” position. cleaned and free of any milk residue. To prepare your cappuccino, we recommend discharging the water in the steam wand. Note: The lights that indicate the aroma are off when dispensing hot water. • To discharge the water in the steam wand, place a container under the steam wand (Pannarello, if supplied).
• Fill 1/3 of the container you wish to use to prepare the cappuccino with cold milk. CLEANING AND MAINTENANCE To ensure better results when preparing a cappuccino, use cold milk straight from the fridge. General Cleaning • Empty and clean the coffee grounds drawer daily, with the machine turned on. • Immerse the steam wand (Pannarello, if supplied) in the milk to be heated. • Turn the selector dial counter-clockwise to set it to the “ ” position.
Pannarello. • We recommend cleaning the water tank daily. For an easier removal of the water tank, move the steam wand / Pannarello upwards: - Remove the small white filter in the water tank and wash it under running drinking water. - Reposition the small white filter in its housing by gently pressing and turning it at the same time. - Fill the water tank with fresh drinking water. • Empty and clean the drip tray daily. Perform this operation also when the float is raised.
DESCALING Limescale normally builds up with the use of the appliance. The machine must be descaled when the icon appears on the display. Steady-on Do not turn the machine off or put it in stand-by mode during the descaling process. Use the Saeco descaling product only. Its formula has been designed to ensure better machine performance and operation for its whole operating life. If correctly used, it also avoids alterations in the brewed product.
Note: if the " " button lights up steady immediately after start-up, the machine needs circuit priming; turn the selector dial clockwise to the " " position. When the " " icon is displayed, turn the selector back to " " position. 10 When the " " icon lights up steady on the display, remove the water tank. 11 Remove the water tank, rinse it and fill it up to the "MAX" level with fresh drinking water.
16 When the rinsing water in the water tank is finished, the " " light starts blinking. 17 Turn the selector dial to the " " position. Empty the container under the steam wand and the one under the dispensing spout. 18 When the " " icon lights up steady on the display, remove the water tank. 22 When the second rinse cycle is over, the machine enters the stand-by mode and the " " button starts blinking. Empty the container under the steam wand and the one under the dispensing spout.
The descaling solution is to be disposed of according to the manufacturer’s instructions and/or the regulations in force in the country of use. After completing the descaling cycle, wash the brew group as described in the "Brew Group" section in the "Cleaning and Maintenance" chapter. Remarks on descaling The previous section explains the correct operations to perform to descale the machine.
CONTROL PANEL DISPLAY Ready Signals • The machine is ready for brewing coffee from • The machine is programming the amount bean and hot water dispensing. of coffee to be brewed for each espresso coffee. Steady on Blinking Steady on Blinking • The machine is programming the amount of • The machine is ready for pre-ground coffee coffee to be brewed for each long coffee. brewing. Steady on Blinking Steady on Blinking Steady on • The machine is brewing 1 cup of espresso coffee.
CONTROL PANEL DISPLAY Blinking Warning Signals Alarm Signals • The machine is warming up to brew coffee • Return the hot water / steam knob to its correct position. and dispense hot water or steam. • Insert the brew group in the machine. Slow Blinking Blinking • Close the service door. • The machine is performing the rinse cycle. • Empty the coffee grounds drawer. Wait until the machine stops the operation. Steady on • Insert the coffee grounds drawer. • The machine needs a descaling cycle.
TROUBLESHOOTING Machine Actions Causes The machine does not turn on. The machine is not connected to the power Connect the machine to the power source. source. The cups are cold. Warm the cups with hot water. The hole of the steam wand is clogged. Clean the hole of the steam wand using a pin. Make sure that the machine is turned off and has cooled before performing this operation. Pannarello is dirty (if supplied). Clean the Pannarello.
TECHNICAL SPECIFICATIONS The manufacturer reserves the right to make changes to the technical specifications of the product. Nominal Voltage - Power Rating - Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See label on the inside of the service door Housing material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• 25 •
• 26 •
• 27 •
Rev.00 del 15-02-13 02 EN 02 The manufacturer reserves the right to change the features of the product without prior notice. www.philips.
