English 02 OPERATING INSTRUCTIONS Type HD8773 02 EN Read carefully before using the machine. FOR HOUSEHOLD USE ONLY Register your product and get support at www.philips.
IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. 2. Do not touch hot surfaces. Use handles or knobs. 3. To protect against fire, electric shock and injury to persons do not immerse cord, plugs, or appliance in water or other liquid. 4. Close supervision is necessary when the appliance is used by or near children. 5. Unplug from outlet when not in use and before cleaning.
CAUTION This appliance is for household use only. Any servicing, other than cleaning and user maintenance, should be performed by an authorized service center. Do not immerse machine in water. To reduce the risk of fire or electric shock, do not disassemble the machine. There are no parts inside the machine serviceable by the user. Repair should be done by authorized service personnel only. 1. Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage. 2.
2 ENGLISH Congratulations on your purchase of a Saeco Minuto One Touch Milk Carafe fully automatic coffee machine! To fully benefit from the support that Saeco offers, please register your product at www.philips.com/welcome. The machine is suitable for preparing espresso coffee using whole coffee beans, and it is supplied with a milk carafe so you can brew a perfect cappuccino in a quick and easy way.
ENGLISH BREWING A COFFEE.........................................................................................26 Brewing a Coffee Using Coffee Beans ......................................................................................................26 Brewing a Coffee Using Pre-Ground Coffee .............................................................................................27 MILK CARAFE..................................................................................................
4 INSTALLATION Product Overview 1 2 3 4 5 6 7 8 9 10 19 11 12 13 14 20 21 31 15 16 17 18 22 32 24 25 26 27 28 29 30 23
ENGLISH General Description 1. Grinder adjustment knob 2. Coffee bean hopper 3. Pre-ground coffee compartment 4. Water tank + Lid 5. Coffee bean hopper lid 6. Control panel 7. Dispensing spout 8. Full drip tray indicator 9. Cup holder grill 10. Drip tray 11. Coffee grounds drawer 12. Brew group 13. Coffee residues drawer 14. Service door 15. Water dispensing spout (removable) 16. Milk carafe 17. Power cord socket 18. Power button 19. Grease for the brew group - to be purchased separately 20. Power cord 21.
6 ENGLISH PREPARING FOR USE Machine Packaging The original packaging has been designed and constructed to protect the machine during transport. We recommend keeping the packaging material for possible future transport. Machine Installation 1 Remove the machine from the packaging. 2 For best use, it is recommended to: • • • Choose a safe, level surface, where there will be no danger of overturning the machine or being injured.
ENGLISH 7 5 Rinse the water tank with fresh water. 6 Fill the water tank with fresh water up to the MAX level and reinsert it into the machine. Make sure it is fully inserted. Caution: Never fill the water tank with warm, hot, sparkling water or any other liquid, as this may cause damage to the water tank and the machine. 7 Remove the coffee bean hopper lid. 8 Slowly pour the coffee beans into the coffee bean hopper.
ENGLISH 12 Switch the power button to “I” to turn on the machine. The “ ” button blinks. 13 To turn on the machine simply press the “ ” button. The machine Yellow automatically primes the circuit. USING THE MACHINE FOR THE FIRST TIME When using the machine for the first time, the following activities need to happen: 1) The machine will prime the circuit; 2) The machine will perform an automatic rinse/self-cleaning cycle. 3) You need to perform a manual rinse cycle.
ENGLISH 9 Yellow Yellow 2 The bar under the icon shows the operation progress. When the process is completed, the machine stops dispensing automatically. 3 Then the control panel shows the machine warm-up icon. Automatic Rinse/Self-Cleaning Cycle When warm-up is complete, the machine automatically performs a rinse/ self-cleaning cycle of the internal circuit with fresh water. This takes less than a minute.
ENGLISH Manual Rinse Cycle During this process you activate the coffee brewing cycle and fresh water flows through the water circuit. This takes a few minutes. Green 1 Place a container under the coffee dispensing spout. Green 10 2 Check that the machine shows this display. 3 Select the pre-ground coffee brewing function by pressing the “ ” button. The machine shows this display. Note: Do not add pre-ground coffee to the compartment. ESPRESSO 4 Check that the lever is set to “ESPRESSO”.
ENGLISH 11 Green 7 Press the “ ” MENU button. The machine shows this display. 8 Press the “ ” button. Green 9 The following icon is displayed. 10 Press the “ ” button to start dispensing hot water. Green 9 This icon is displayed. The machine reminds you to install the water dispensing spout. Check that the water dispensing spout is correctly installed. Press “ ” to confirm. The machine will start dispensing hot water.
ENGLISH Red 10 Dispense water until the no water icon appears. Note: The manual rinse cycle may be stopped by pressing the “ ” button. 11 Fill the water tank again up to the MAX level. Now the machine is ready Green 12 for coffee brewing. The display to the left will be shown. Note: When you haven’t used the machine for 2 or more weeks, the machine will automatically perform an automatic rinse/self-cleaning cycle after you switch it on.
ENGLISH 13 Measuring and Programming Water Hardness Water hardness measuring is very important in order to define the descaling frequency and to install the “INTENZA+” water filter (for more detail on the water filter, see next chapter). To measure the water hardness follow the steps below: 1 Immerse the water hardness test strip (supplied with the machine) in water for 1 second. Note: The test strip can only be used for one single measurement. 2 Wait for one minute.
Yellow ENGLISH 5 Press the “ ” button to enter the programming menu. Press the “ button to scroll the functions until this icon appears. ” Yellow Note: The machine is supplied with a standard water hardness setting, suitable for most types of water. 6 Press the “ ” button to increase the value or the “ crease the value. ” button to de- 7 Press the “ ” button to confirm the setting. 8 Press the “ Green 14 ” button to exit the programming MENU. The machine shows this display and is ready to brew.
ENGLISH 15 1 Remove the small white filter from the water tank and store it in a dry place. 2 Remove the “INTENZA+” water filter from its packaging, immerse it vertically (with the opening positioned upwards) in cold water and gently press the sides so as to let the air bubbles out.
ENGLISH Yellow Yellow Green 8 Press the “ ” MENU button. The machine shows this icon. 9 Press the “ ” button to enter the programming menu. Press the “ button to scroll the functions until this icon appears. 10 Press the “ ” button to select “ON” and press the “ Green ” ” button to con- firm. 11 To exit, press the “ ” button. The machine shows this display and is ready to brew. The machine has now been programmed to inform the when to replace the “INTENZA+” water filter.
ENGLISH 17 Yellow Yellow Green 2 Press the “ ” MENU button. The machine shows this icon. 3 Press the “ ” button to enter the programming menu. Press the “ button to scroll the functions until this icon appears. 4 Select the “RESET” option. Press the " " button to confirm. 5 To exit, press the “ Green ” ” button. The machine shows this display and is ready to brew. Yellow The machine is now programmed to manage a new “INTENZA+” water filter.
18 ENGLISH ADJUSTMENTS The machine allows for certain adjustments so that you can brew the best tasting coffee possible. Saeco Adapting System Coffee is a natural product and its characteristics may change according to its origin, blend and roast. The machine is equipped with a self-adjusting system that allows the use of all types of coffee beans available on the market except for flavored coffee beans.
ENGLISH 19 2 The reference marks inside the coffee bean hopper indicate the grind setting. There are 5 different grind settings to choose from position 1 for coarse grind - lighter taste to position 2 for fine grind - bolder taste 2 Adjusting the Aroma (Coffee Strength) Choose your favorite coffee blend and adjust the amount of coffee to be ground according to your personal taste. You can also select the preground coffee function. Green Note: Selection must be made prior to selecting coffee.
20 ENGLISH Adjusting the Coffee Dispensing Spout The height of the dispensing spout can be adjusted to better fit the dimensions of the cups that you wish to use. The lower part of the dispensing spout can be removed to allow a tumbler to be used. Move the dispensing spout up or down with your fingers to adjust its height as shown in the image. The recommended positions are: For the use of small cups; For the use of large cups.
ENGLISH 21 Remove the lower part of the dispensing spout to allow a tumbler to be used. Note: Before installing the lower part of the dispensing spout, clean it together with the upper part. “ESPRESSO” or “COFFEE” Selection Lever The machine allows you to adjust the brewing pressure according to the desired beverage type. This selection allows you to optimize machine operation to improve the quality of coffee brewing and the desired result in the cup.
ENGLISH The lever allows two types of brewing: ESPRESSO 1 Push the lever downwards to select the “ESPRESSO” function. Red In this position you can brew an espresso coffee by pressing the “ button or a cappuccino by pressing the “ ” button. ” Note: If an espresso, or a cappuccino is selected with the lever in the wrong position, the following icon will be displayed reminding you to set the lever to the correct position. 2 Push the lever upwards to select the “COFFEE” function.
ENGLISH 23 Adjusting the Coffee Length The machine allows you to adjust the amount of brewed coffee according to your taste and the size of your cups. Each time the “ ”, “ ” or “ ” button is pressed, the machine brews a pre-set amount of beverage. Each button may be individually programmed for a specific brew setting. The following procedure describes how to program the “ ” button. 1 Place a cup under the dispensing spout.
ENGLISH BREWING ESPRESSO Before brewing espresso, make sure that there are no warnings shown on the control panel, and that the water tank and coffee bean hopper are filled. Brewing an Espresso Using Coffee Beans 1 Place 1 or 2 cups under the dispensing spout. 2 Push the lever downwards to select the “ESPRESSO” function. ESPRESSO 3 To brew an espresso, press the “ ” button to select the desired Green aroma. 4 To brew an espresso, press the “ ” button once. This icon will be displayed.
ENGLISH 25 6 After the prebrewing cycle, coffee begins to pour out of the dispensing spout. 7 Coffee brewing stops automatically when the set level is reached. However, it is possible to stop the coffee brewing earlier by pressing the “ ” button. Brewing an Espresso Using Pre-Ground Coffee This function allows you to use pre-ground coffee. With the pre-ground coffee function you can only brew one coffee at a time. 1 Push the lever downwards to select the “ESPRESSO” function.
ENGLISH 4 Press the “ ” button to brew an espresso. The brewing cycle starts. 5 After the prebrewing cycle, coffee begins to pour out of the dispensing spout. 6 Brewing stops automatically when the set level is reached. However, it is possible to stop the coffee brewing earlier by pressing the “ ton. ” but- After brewing, the machine returns to the main menu. Green 26 Repeat the steps described above to brew more coffees using pre-ground coffee.
ENGLISH 27 2 Push the lever upwards to select the “COFFEE” function. COFFEE Green 3 To brew the beverage, press the “ ” button to select the desired aroma. 4 To brew a medium coffee, press the “ ” button only once. This icon Green will be displayed. 5 To brew a long coffee, press the “ ” button once. This icon will be displayed. Note: In this operating mode, the machine automatically grinds and doses the correct amount of coffee.
ENGLISH ” button to select the pre-ground coffee function. Green 2 Press the “ 3 Lift the pre-ground coffee compartment lid and add one measuring scoop of pre-ground coffee to the compartment. Use only the measuring scoop supplied with the machine. Then close the pre-ground coffee compartment lid. Warning: Add only pre-ground coffee to the pre-ground coffee compartment. Other substances and objects may cause severe damage to the machine. Such damage will not be covered by warranty.
ENGLISH 29 MILK CARAFE This chapter explains how to use the milk carafe to prepare a cappuccino or to froth the milk. Note: Before using the milk carafe, clean it thoroughly as described in the “Cleaning and Maintenance” chapter. We recommend that you fill the carafe with cold (5°C / 41°F) milk with a protein content of at least 3% to ensure optimum results when preparing a cappuccino. Whole milk or skimmed milk may be used depending on individual taste.
30 ENGLISH Inserting the Milk Carafe 1 If installed, remove the water dispensing spout as shown in the figure: - Press the two buttons on the side to unlock it and lift it slightly; Pull the water dispensing spout to remove it. 1 2 2 Slightly tilt the milk carafe. Insert it all the way into the guides of the machine. 3 Push the carafe towards the bottom while rotating at the same time, until it is locked at the drip tray. Do not use force while inserting the carafe.
ENGLISH 31 Emptying the Milk Carafe 1 A B 1 Press one of the release buttons at the side to remove the top of the carafe as shown in the figures (A or B). 1 2 Lift the top of the carafe. Empty the milk carafe and clean it properly. Note: After each use, clean the milk carafe as described in the “Cleaning and Maintenance” chapter.
32 ENGLISH BREWING A CAPPUCCINO Warning: Danger of burning! Dispensing may be preceded by short sprays of milk and steam. Danger of burning! Wait until the end of the cycle before removing the milk carafe. 1 Fill the milk carafe with milk. The level must be between the minimum (MIN) and maximum (MAX) indication on the milk carafe. Note: Use cold (5 °C / 41°F) milk with a protein content of at least 3% to ensure optimum results when preparing a cappuccino.
ENGLISH 33 5 Place a cup under the dispensing spout. 6 Check that the lever is set to “ESPRESSO”. ESPRESSO Red 7 Press the “ ” button to start the dispensing procedure. Note: If an espresso, or a cappuccino is selected with the lever in the wrong position, the following icon will be displayed reminding you to set the lever to the correct position. Green 8 The machine reminds you to insert the carafe and pull out the milk carafe dispenser.
ENGLISH Yellow 9 This icon is displayed during preheating time required by the machine. Green 10 When the machine shows the following icon, the machine pours the milk. Dispensing can be stopped by pressing the “ ” button. 11 Once the froth milk has been dispensed, the machine brews the coffee. Verde 34 Dispensing can be stopped by pressing the “ ” button. 12 Slide the milk carafe dispenser back to the “ ” icon.
ENGLISH 35 Adjusting the Cappuccino Length Each time the “ ” button is pressed, the machine pours a pre-set quantity of cappuccino into the cup. The machine allows you to adjust the amount of cappuccino brewed according to your taste and the size of your cups. 1 Fill the carafe with milk and insert it into the machine. 2 Slide the milk carafe dispenser to the right up to the “ ” icon. Make sure that the dispensing spout handle is perfectly aligned to the ”.
ENGLISH 6 Press and hold the “ Red ” button until the “MEMO” icon appears on the display. Then release the button. The machine is now in programming mode. Note: If an espresso, or a cappuccino is selected with the lever in the wrong position, the following icon will be displayed reminding you to set the lever to the correct position. Yellow Green 7 The machine reminds you to insert the carafe and pull out the milk carafe dispenser.
ENGLISH 37 FROTHING MILK Warning: Danger of burning! Dispensing may be preceded by short sprays of milk and steam. Danger of burning! Wait until the end of the cycle before removing the milk carafe. 1 Fill the milk carafe with milk. The level must be between the minimum (MIN) and maximum (MAX) indication on the milk carafe. Note: Use cold (5 °C / 41°F) milk with a protein content of at least 3% to ensure optimum results when preparing a cappuccino.
ENGLISH 5 Place a cup under the dispensing spout. Green Green 6 Press the “ ” MENU button. The following icon is displayed. 7 Press the “ ” button. The machine shows this display. 8 Press the “ ” button to select froth milk. 9 The machine reminds you to insert the carafe and pull out the milk Green 38 carafe dispenser.
Yellow ENGLISH 39 10 This icon is displayed during preheating time required by the machine. Green 11 The machine dispenses a predefined quantity of froth milk into the cup. Dispensing can be stopped by pressing the “ ” button. 12 Slide the milk carafe dispenser back to the “ ” icon. Note: After using the milk carafe, clean it as described in the "Cleaning and Maintenance" chapter.
ENGLISH 4 Place a cup under the dispensing spout. Green Green 5 Press the “ ” MENU button. The following icon is displayed. 6 Press the “ ” button. The machine shows this display. 7 Press and hold the “ ” button to select froth milk until the “MEMO” icon appears on the display. Then release the button. The machine is now in programming mode. 8 The machine reminds you to insert the carafe and pull out the milk Green 40 carafe dispenser.
Yellow ENGLISH 41 6 This icon is displayed during preheating time required by the machine. Green 7 When the desired amount of froth milk is reached, press the “ ” but- ton. Now the “froth milk” button is programmed. Every time it is pressed, the machine will brew the same amount of froth milk that was programmed. DISPENSING HOT WATER Warning: Danger of burning! Dispensing may be preceded by short sprays of hot water and steam.
ENGLISH 3 Place a container under the hot water dispensing spout. Green Green 4 Press the “ ” MENU button. The following icon is displayed. 5 Press the “ ” button. The machine shows this display. 6 Press the “ ” button to start dispensing. 7 This icon is displayed. The machine reminds you to install the water Green 42 dispensing spout. Check that the water dispensing spout is correctly installed. Press “ ” to confirm. The machine will start dispensing hot water.
ENGLISH 43 Yellow 8 This icon is displayed during preheating time required by the machine. Green 9 Dispense the desired amount of hot water. To stop the hot water dispensing, press the “ ” button. CLEANING AND MAINTENANCE Daily cleaning of the machine Caution: Timely cleaning and maintenance of your machine is very important as it prolongs the life of your machine.
44 ENGLISH 2 Remove the coffee grounds drawer and empty it. 3 Empty and clean the drip tray. 4 Insert the coffee grounds drawer back into the drip tray and this into the machine. 1 2 Note: Also empty the drip tray and coffee grounds drawer when the full drip tray indicator is raised. Daily cleaning of the water tank 1 Remove the small white filter or the “INTENZA+” water filter (if installed) from the water tank and wash it with fresh water.
ENGLISH 45 Daily Cleaning of the Milk Carafe It is important that you clean the milk carafe daily or after each use as it preserves hygiene and ensures perfect froth milk consistency. Warning: Danger of burning! Dispensing may be preceded by short sprays of hot water and steam. Danger of burning! Wait until the end of the cycle before removing the milk carafe. 1 A B 1 Press one of the release buttons at the side to remove the top of the carafe as shown in the figures (A or B).
ENGLISH 4 Remove the lid and fill the milk carafe up to the MAX level with fresh water. 5 Slide lid back onto the milk carafe. 6 Pull out the milk carafe dispenser to the right up to the “ ” icon. 7 Place a container under the dispensing spout. 8 Press the “ ” MENU button. The following icon is displayed.
Green ENGLISH 47 9 Press the “ ” button. The machine shows this display. 10 Press the “ ” button to select froth milk. Yellow Green 11 The machine reminds you to insert the carafe and pull out the milk carafe dispenser. 12 This icon is displayed during preheating time required by the machine. Green 13 Once the machine stops dispensing water, the cleaning is finished. 14 Slide the milk carafe dispenser back to the “ ” icon. Remove the milk carafe and empty it.
ENGLISH 48 Weekly Cleaning of the Machine 1 Clean the seat of the drip tray. Weekly Cleaning of the Milk Carafe The weekly cleaning is more thorough since all milk residue is removed from the dispenser. 1 A 1 Press one of the release buttons at the side to remove the top of the B 1 carafe as shown in the figures (A or B).
ENGLISH 49 2 Remove the lid. 3 Lift the dispensing spout to remove it from the top of the carafe. The milk carafe dispenser is made up of five parts that must be disassembled. Each part is indicated by a capital letter (A, B, C, D, E) as shown in the figure below. 4 Remove the suction tube with the fitting (A) from the milk frother. A 5 Remove the fitting (B) from the suction tube. B 6 Detach the lid (C) from the milk carafe dispenser by pushing C downwards while slightly pressing on the sides.
50 ENGLISH 7 Disassemble further as shown in the figure. D 8 Remove the fitting (E) from the milk frother by pulling it outwards. E 9 Clean all the parts thoroughly with lukewarm water. Note: You can also clean individual parts in the dishwasher. 10 Reassemble the parts following the reverse order. Weekly Cleaning of the Brew Group and the Coffee Exit Chute The brew group should be cleaned every time the coffee bean hopper is filled or at least once a week.
ENGLISH 51 2 Raise the dispensing spout and remove the drip tray and coffee grounds drawer by pressing the side buttons. Only at this time open the service door. 1 2 3 2 3 To remove the brew group, press the «PUSH» button and pull it by the handle. Pull it out horizontally without turning it. 4 Remove the coffee residues drawer and wash it thoroughly. 5 Clean the coffee exit chute thoroughly with a spoon handle or with another round-tipped kitchen utensil.
52 ENGLISH 6 Thoroughly wash the brew group with lukewarm water and carefully clean the upper filter. Caution: Do not use detergent or soap to clean the brew group. 7 Let the brew group air-dry thoroughly. 8 Thoroughly clean the inside of the machine using a soft, dampened cloth. 9 Make sure the brew group is in the off position; the two reference signs must match. If they do no match up, proceed as described in steps 1011.
ENGLISH 53 12 Insert the coffee residues drawer into its seat and ensure that it is correctly in place. Note: If the coffee residues drawer is not correctly positioned, the brew group may not fit into the machine. 13 Insert the brew group into its seat again until it locks into place without pressing the “PUSH” button. 14 Insert the coffee grounds drawer with the drip tray back into the machine and close the service door.
54 ENGLISH Monthly Lubrication of the Brew Group Lubricate the brew group after approximately 500 coffees or once a month. The grease to lubricate the brew group can be purchased separately. For further details, please refer to the maintenance products page in this manual. Caution: Before lubricating the brew group, clean it with fresh water and let it dry, as described in the “Weekly Cleaning of the Brew Group” chapter. 1 Apply the grease evenly on both side guides. 2 Also lubricate the shaft.
ENGLISH 55 3 Insert the brew group into its seat until it locks into place (see the “Weekly Cleaning of the Brew Group” chapter). 4 Insert the coffee grounds drawer with the drip tray back into the machine and close the service door. Monthly Cleaning of the Coffee Bean Hopper Clean the coffee bean hopper once a month when it is empty with a damp cloth to remove coffee oil. Thereafter refill it with coffee beans.
56 ENGLISH DESCALING The descaling process takes approx. 35 minutes. Yellow Limescale builds up inside the machine during use. It needs to be removed regularly as it may clog the water and coffee circuit of your machine. The machine indicates when descaling is needed. If the machine display shows the CALC CLEAN icon, it means that you need to descale it. Caution: Not doing this will ultimately make your machine stop working properly, and in this case repair is NOT covered by your warranty.
ENGLISH 57 2 Fill the milk carafe with water up to the MIN level and insert it back into the machine. 3 Remove the “INTENZA+” water filter from the water tank if it was installed and replace it with the small white original one. Place the water tank back into the machine. Yellow Green 4 Press the “ ” MENU button. The following icon is displayed. 5 Press the “ Yellow 6 Press the “ Yellow ” button. Press the “ ” button until the following icon is shown. ” button to start the descaling process.
ENGLISH 8 Remove the water tank and pour in the entire contents of the descaling solution. Then top up the tank with fresh water up to the CALC CLEAN level. 9 Place the water tank back into the machine. 10 Pull out the milk carafe dispenser to the right up to the “ Yellow ” icon. Place a large container (1.5l/ 5.7oz) under both the milk carafe dispenser and the dispensing spout. Yellow 58 11 Press the “ ” button to start the descaling cycle.
Yellow ENGLISH 59 Note: The descaling cycle may be paused by pressing the “ ” button. To resume the cycle, press the “ ” button again. This allows you to empty the container or to leave the machine unattended for a short time. Red 13 When this icon is displayed, the water tank is empty. 14 Remove the water tank, rinse it and fill it up to the MAX level with fresh water. Place it back into the machine. 15 Remove and empty the container and the milk carafe. 16 Empty the drip tray and place it back.
Yellow ENGLISH 18 Press the “ ” button to start the rinse cycle. Note: The rinse cycle may be paused by pressing the “ ” button. To resume the cycle, press the “ ” button again. This allows you to empty the container or to leave the machine unattended for a short time. Red 19 When this icon is displayed, the water tank is empty. Repeat steps 1417. When the machine shows this icon again, go to step 20.
ENGLISH 61 26 Remove and empty the container. 27 Empty the drip tray and place it back. 1 2 28 The descaling cycle is now complete. 3 2 29 Remove the small white filter and place back the “INTENZA+” water filter into the water tank if it was installed. Note: At the end of the descaling cycle, wash the brew group as described in the “Weekly Cleaning of the Brew Group” chapter.
ENGLISH PROGRAMMING It is possible to customize the machine's functions via the programming menu. Yellow Yellow Yellow Yellow Yellow The following settings can be adjusted Yellow 62 Coffee Temperature This function allows you to adjust the coffee brewing temperature. Timer (stand-by) This function adjusts the time taken for the machine to go into stand-by mode after the last brewing. Contrast This function allows you to adjust the contrast of the display to better view the messages.
Yellow ENGLISH 63 Factory Settings This function allows you to reset all factory values. How to Program the Machine The programming menu can only be accessed when the machine is on and shows this display. 1 Press the “ ” button to enter the menu. 2 Press the “ ” button to access programming. Yellow Yellow Green In this example, it is shown how to program the display contrast. Proceed in the same way to program the other functions. 3 The main screen will be displayed.
ENGLISH 4 Press the “ Yellow ” button to scroll the pages until the display contrast function is displayed. 5 Press the “ ” and “ ” buttons to increase or decrease the value of the function. Yellow 64 6 When the display value is changed, the “OK” message appears. Press the “ ” button to confirm the change. 7 Press the “ ” button to exit the programming menu. Note: The machine automatically exits programming mode if no button is pressed for 3 minutes.
ENGLISH 65 MEANING OF THE DISPLAY ICONS This machine is equipped with a color-coded system to make the user’s understanding of the display signals easier. The icons are color-coded according to the traffic light principle. Ready Signals (Green color) The machine is ready to brew products. The machine is ready to brew pre-ground coffee. The machine is brewing one cup of espresso. The machine is brewing two cups of espresso. The machine is programming the amount of espresso to be brewed.
66 ENGLISH Ready Signals (Green color) Select the programming menu or special beverages menu. Froth milk or hot water selection. Hot water dispensing. Froth milk dispensing. The machine is frothing the milk for the cappuccino. The machine is brewing the coffee for the cappuccino. The machine is programming the amount of milk to be dispensed for cappuccino. The machine is programming the amount of coffee to be brewed for cappuccino.
ENGLISH 67 Ready Signals (Green color) The machine will remind the user that the carafe must be inserted when programming a product containing milk. Warning Signals (Yellow color) The machine is in warm-up phase to brew beverages or dispense hot water/ steam. The machine is performing the rinse cycle. Wait until the machine has completed the cycle. The machine needs the "INTENZA+" water filter to be replaced. The brew group is being reset due to machine reset.
68 ENGLISH Warning Signals (Red color) Completely insert the drip tray with the coffee grounds drawer into the machine and close the service door. Fill the coffee bean hopper and refit the lid. The brew group must be inserted into the machine. Empty the coffee grounds drawer. Wait 5 seconds before reinserting it. Set the “ESPRESSO” or “COFFEE” selection lever to “ESPRESSO” within 30 seconds to complete brewing.
ENGLISH 69 TROUBLESHOOTING This chapter summarizes the most common problems you could encounter with your machine. If you are unable to solve the problem with the information below, visit www.philips.com/support for a list of frequently asked questions or contact the Philips Saeco hotline in your country. The contact details can be found in the warranty booklet supplied separately or on www.philips.com/support. Machine actions Causes The machine does not switch on.
70 ENGLISH Machine actions Causes Solutions Coffee is too weak. (see note) This might occur when the machine is automatically adjusting the dose. Brew a few cups of coffee as described in the “Saeco Adapting System” chapter. Coffee is brewed slowly. (see note) The coffee grind is too fine. Change coffee blend or adjust the grind as explained in chapter “Adjusting the Ceramic Coffee Grinder”. The circuit is not primed. Prime the circuit (see the "Using the Machine for the First Time" chapter).
ENGLISH 71 ENERGY SAVING Stand-by The Saeco full automatic espresso machine is designed for energy saving proven by the Class A energy label. After 30 minutes of inactivity, the machine turns off automatically (unless a different stand-by time has been programmed). If a product has been brewed the machine performs a rinsing cycle. In stand-by mode, the energy consumption is below 1Wh. To turn on the machine, press the “ ” button (if power button on the back of the machine is set to “I”).
72 ENGLISH TECHNICAL SPECIFICATIONS The manufacturer reserves the right to make changes to the technical specifications of the product Nominal Voltage - Power Rat- See data plate on the inside of the service ing - Power Supply door Housing material Thermoplastic material Size (w x h x d) 215 x 330 x 429 mm / 8.5” x 13” x 16.9” Weight 7.5 kg / 16.5 pounds Power cord length 800 - 1200 mm / 32-47” Control panel Front panel Cup sizes Up to 152 mm / 6” Water Tank 1.8 litres / 60.
ENGLISH 73 ORDERING MAINTENANCE PRODUCTS For cleaning and descaling, use Saeco maintenance products only. You can purchase these at the Philips online shop (if available in your country) at www.shop.philips.com/service, your local dealer or at authorised service centres. If you have any difficulties obtaining maintenance products for your machine, please contact the Philips Saeco hotline in your country. The contact details can be found in the warranty booklet by-packed separately or on www.philips.
74 ENGLISH - 996530070318 (www.buyphilipsparts.com) - 996530011867 (www.buyphilipsparts.
02 EN Rev.00 del 15-01-14 02 The manufacturer reserves the right to make changes without prior notice. www.philips.
