Register your product and get support at www.saeco.com/welcome HD8759/47 4219_460_3143_1_DFU-Simple_A5_v2.
English 5
1 5 2 6 3 7 8 9 10 4 11 12 13 14 ESPRESSO MILK FROTH ESPRESSO LUNGO HOT WATER 19 18 15 17 AR OM A STR ENG 20 MENU TH 16 21 22 28 27 23 26 25 24
English 5 Contents Introduction Important safeguards 5 6 Caution Instructions for the power supply cord 6 7 General description Important 7 7 Warning Caution Electromagnetic fields (EMF) 8 8 9 The display First installation 9 10 Manual rinsing cycle 10 Water filter 10 Installing the water filter Replacing the water filter 11 11 Measuring the water hardness Using the machine 12 12 Brewing coffee with beans Brewing coffee with pre-ground coffee Adjusting the coffee quantity Adjusting the g
English coffee beans. To fully benefit from the support that Saeco offers, please register your product at www.saeco.com/welcome. This user manual applies to all Intelia/Intelia Deluxe models with automatic milk frother. Important safeguards When using electrical appliances, basic safety precautions should always be followed, including the following: 1 Read all instructions. 2 Do not touch hot surfaces. Use handles or knobs.
English 7 Instructions for the power supply cord - A short power-supply cord (or detachable power-supply cord) is to be provided to reduce risks resulting from becoming entangled in or tripping over a longer cord. - Longer detachable power-supply cords or extension cords are available and may used if care is exercised in their use. - If a long detachable power-supply cord or extension cord is used.
English Warning - Check if the voltage indicated on the machine corresponds to the local voltage before you connect the machine - Connect the machine to a grounded wall outlet. - Do not let the power supply cord hang over the edge of a table or counter, or touch hot surfaces. - Never immerse the machine, power plug or power supply cord in water (danger of electrical shock). - Do not pour liquids on the power supply cord connector. - Never direct the hot water jet towards body parts: danger of burns.
English 9 - The machine is for household use only. It is not intended for use in environments such as canteens, staff kitchen of shops, offices, farms or other work environments. - Always put the machine on a flat and stable surface. - Do not place the machine on hot surfaces, directly next to a hot oven, heater or similar source of heat. - Only put roasted coffee beans into the coffee bean hopper.
English - MENU button = DOWN button: press this button to scroll down through the display menu. MENU First installation 1 2 3 4 5 6 7 8 9 10 11 Slide the drip tray with drip tray cover into the machine. Remove the water tank. Fill the water tank to the MAX level with fresh water. Fill the coffee bean hopper with coffee beans. Insert the small plug into the socket located on the back of the machine. Insert the power plug into the electrical outlet.
English 11 Installing the water filter 1 Remove the small white filter from the water tank and store it in a dry place. Note: Please keep the small white filter for future use.You will need it for the descaling process. FILTER FILTER 2 Remove the filter from its packaging and immerse it in cold water with the opening pointing upwards. Press the sides of the filter gently to let out the air bubbles. 3 Place the filter in the empty water tank. Press it down until it cannot move any further.
English Measuring the water hardness To be able to adjust the machine settings to the water in your region, please measure the water hardness with the water hardness strip supplied. 1 Immerse the water hardness test strip (supplied with the machine) in fresh water for 1 second. 2 Remove the water hardness strip and and wait for 1 minute. 3 Check how many squares have changed into the red color and check the water hardness in below table.
English 13 Brewing coffee with pre-ground coffee When you brew coffee with pre-ground coffee, use the measuring scoop in the multifunctional tool supplied to put the correct dose in the pre-ground coffee compartment. If you add more pre-ground coffee, the excess coffee will end up in the coffee grounds drawer. 1 Open the lid of the pre-ground coffee compartment. 2 Pour one measuring scoop of pre-ground coffee into the compartment.
English 1 Insert the suction tube into the automatic milk frother. 2 Insert the automatic milk frother on the rubber grip until it locks into place. 3 Insert the suction tube into the milk pitcher. 4 Place a cup on the drip tray under the automatic milk frother and press the MILK FROTH button. - The machine dispenses the frothed milk directly into the cup. 5 Press the OK button to stop frothing Hot water Warning: Danger of scalding. Only grab the steam wand by its protective handle.
English 1 15 Remove the automatic milk frother from the steam wand. 2 Place a container under the steam wand. 3 Press the HOT WATER button. Hot water dispensing starts automatically. 4 Press the OK button to stop hot water dispensing. Remove the container. Descaling You have to descale the machine when the display shows the CALC CLEAN icon. If you do not descale when the display shows the CALC CLEAN icon, the machine may stop working properly. In this case, repairs are not covered by the warranty.
English CALC CLEAN 5 The display shows the following icon to indicate that the machine enters the descaling cycle. If you want to exit the descaling cycle, press the ESC button. 6 Pour the entire bottle of Saeco descaling solution (250ml) into the water tank. 7 Add water to the descaling solution in the water tank up to the CALC CLEAN indication. 8 Place a large container (1.5 l) under the steam wand and dispensing spout. 9 Press the OK button to start the descaling cycle.
English 17 before brewing any beverage. If the cycle was not completed, the machine will require another descaling cycle to be performed at your earliest convenience. Cleaning and maintenance Weekly cleaning of the brew group Clean the brew group once per week. 1 Remove the coffee grounds container and open the service door. 2 Remove the coffee residues drawer. 3 To remove the brew group, press the lever and pull the brew group out of the machine.
English 7 The hook is not correctly positioned if it is still in bottommost position. 8 Slide the brew group back into the machine along the guiding rails on the sides until it clicks into position. Then place the coffee residues drawer back in the machine. Lubrication Lubricate the brew group after approximately 500 cups of coffee or once a month. 1 Apply some lubricant around the shaft in the bottom of the brewing unit. 2 Apply lubricant to the rails on both sides, as shown in the illustration.
English 19 6 Rinse the pitcher with fresh water and fill it with a half litre of fresh water for the rinsing cycle. Empty the container and place it back under the automatic milk frother. 7 Insert the suction tube into the pitcher. 8 Press the MILK FROTH button. 9 You can press OK to stop or let the machine dispense until it stops automatically. 10 Remove the automatic milk frother from the steam wand. Remove the rubber grip from the steam wand. The steam wand can be hot after use.
English 16 Attach the automatic milk frother to the fitting and make sure it is locked into place. 17 Attach the suction tube. 18 Insert the rubber grip back on the steam wand. Insert the automatic milk frother on the rubber grip until it locks into place. Warranty and support If you need information or support, please visit www.saeco.com/support or read the separate worldwide guarantee leaflet. To buy spare parts, visit www.shop.philips.
English - Fill the water tank with fresh water to the MAX level indication. - The bean hopper is empty. Put new coffee beans in the bean hopper. - The brew group is not in the machine. Insert the group. - Close the service door. - Remove the coffee grounds container and empty it.
English - There is too much powder in the brew group. Clean the brew group. - If an error code is triggered, check the section 'Meaning of error codes' to see what the code on the display means and what you can do. The machine cannot be used when this icon is on the display. - You forgot to place the lid on the pre-ground coffee compartment. If you do not place it back within 30 seconds the display will return to the main menu and the brewing cycle will be stopped.
English 23 The machine does not turn on The machine is disconnected. Check if the power supply cord is inserted correctly The machine is in DEMO mode. The standby button has been Switch the machine off and then on pressed for more than 8 seconds. again. The drip tray is quickly filled. This is normal. The machine uses Empty the drip tray when the 'drip tray water to rinse the internal circuit full' full indicator pops up through the and brew group. Some water drip tray cover.
English The coffee is not hot enough. The machine grinds the coffee beans, but coffee does not come out. The coffee comes out slowly. The coffee exit duct is dirty. Clean the coffee exit duct thoroughly with the handle of the multifunctional tool or a spoon handle. The coffee blend is not the correct one. Try another coffee blend. The machine is performing its self-adjustment. Brew a few cups of coffee. The cups you use are cold. Preheat the cups by rinsing them with hot water.
English 25 There is water under the machine. There is still water in the water tank. Empty the water tank before you install the filter. The drip tray is too full and overflowed. Empty the drip tray when the drip tray full indicator pops up through the drip tray. Always empty the drip tray before you start descaling the machine. The machine is not placed on a horizontal surface. Place the machine on a horizontal surface so that the drip tray full indicator works properly.
www.saeco.com/welcome 4219_460_3143_1_Book_Simp_A5_v2.indd 80 4219.460.3143.
