del 15-02-12 02 EN Rev.01 02 The manufacturer reserves the right to change the features of the product without prior notice. www.philips.
Register your product and get support at 02 English www.philips.com/welcome Type HD8743 / HD8745 / HD8747 SUP 033R 02 EN OPERATING INSTRUCTIONS READ THESE OPERATING INSTRUCTIONS CAREFULLY BEFORE USING THE MACHINE.
•2• IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. 2. Do not touch hot surfaces. Use handles or knobs. 3. To protect against fire, electric shock and injury to persons do not immerse cord, plugs, or appliance in water or other liquid. 4. Close supervision is necessary when the appliance is used by or near children. 5. Unplug from outlet when not in use and before cleaning.
CAUTION This appliance is for household use only. Any servicing, other than cleaning and user maintenance, should be performed by an authorized service center. Do not immerse machine in water. To reduce the risk of fire or electric shock, do not disassemble the machine. There are no parts inside the machine serviceable by the user. Repair should be done by authorized service personnel only. 1 Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage.
•4• GENERAL INFORMATION The coffee machine is suitable for preparing espresso coffees using whole coffee beans and is equipped with a device to dispense steam and hot water. The machine is designed for domestic use and is not suitable for heavy or professional use. Keep these operating instructions in a safe place and make them available to anyone who may use the coffee machine.
•5• Keep children under control to prevent them from playing with the product. Children are not aware of the risks related to electric household appliances. Do not leave the machine packaging materials within the reach of children. Danger of Burns Never direct the jet of hot steam and/or hot water towards yourself or others: Danger of scalding! Always use the handles or knobs provided.
•6• Pannarello (optional - only available for certain models) Coffee bean hopper lid Coffee bean hopper Dispensing spout Full drip tray indicator Service door Dregdrawer Control panel Protective handle Hot water/steam wand Grill Drip tray Brew group Water tank Small coffee button Double coffee light and brewed coffee length setting Temperature light Brew group lubricant ON/OFF button Power cord Warning light Large coffee button Grinder adjustment key Water tank level light Control dial
INSTALLATION • Remove the water tank. For your safety and the safety of others, carefully follow the instructions provided in the “Safety Regulations” section. • Rinse and fill it with fresh water making sure that it is not filled exceeding the MAX level indicated in the water tank. Put the water tank back in its seat to its limit stop. Machine Packaging Use only fresh, non-sparkling water to fill the tank. Hot water or any other liquid may damage the tank and/or the machine.
•8• • Make sure control dial is on “ ” position; if this is not the case, set it to that position. • Simply press the ON/OFF button to turn the machine on; the “ “ light will begin to blink rapidly indicating that the water circuit must be primed. Note: Before starting the machine for the first time, prime the water circuit. Using the machine for the first time or after a long period of inactivity. These simple operations will make it possible to always brew excellent coffee.
•9• Steady on This cycle will rinse the internal circuits with fresh water. The cycle is carried out: • At machine start (with cold boiler) • After priming the water circuit (with cold boiler) • During the standby preparation phase (if a coffee product has been brewed) • During the turning off phase after pressing the ON/OFF button (if a coffee product has been brewed). Note: Before dispensing, place a container beneath the dispensing spout.
• 10 • Coffee Grinder Adjustment Adjusting the Brewed Coffee Warning! The grinder adjustment knob, inside the coffee bean hopper, must be turned only when the grinder is working. Do not pour ground and/or instant coffee into the coffee bean hopper. The machine allows you to adjust the amount of brewed coffee according to your taste and/or the size of your cups. Each time the “ “ or “ “ buttons are pressed and released, the machine brews a pre-set amount of coffee.
Steady on COFFEE BREWING DISPENSING HOT WATER Before brewing coffee, make sure that the green temperature light “ “ is steady on and that the water tank and the coffee hopper are full. Warning: Dispensing may be preceded by short sprays of hot water, and scalding is possible. The hot water/steam wand may reach high temperatures. Do not touch it with bare hands; use the appropriate handle only. Leave the control dial on the coffee position “ ” during the dispensing phase.
• 12 • STEAM DISPENSING / CAPPUCCINO BREWING to set it to the “ ” position. Froth the milk by gently swirling the cup and moving it up and down. • After dispensing steam for the desired time, turn the control dial clockwise and set it back to the “ ” position to stop dispensing steam. • The same procedure can be used to heat other beverages. After using the steam wand (Pannarello, if supplied), wash it as described in the “Cleaning and Maintenance” section.
CLEANING AND MAINTENANCE General Cleaning • Empty and clean the dregdrawer daily, with the machine turned on. • Maintenance and cleaning operations can only be carried out when the machine is turned off and unplugged. • Do not immerse the machine in water. • Do not wash any of its parts in the dishwasher. • Do not use alcohol, solvents, and/or abrasive objects to clean the machine. • Use a soft, dampened cloth to clean the machine.
• 14 • • Make sure that the lever is in contact with the brew group. Press the “PUSH” button to make sure that the brew group is in the correct position. Warning! Never drink the descaling solution or any products dispensed until the cycle has been carried out to the end. Never use vinegar as a descaling solution. Lubricate the brew group after approximately 500 brewing cycles. The brew group lubricant may be purchased through Saeco or authorized service centers.
8 Turn the selector switch clockwise to the “ ” position. The machine rinse cycle starts. 9 When the water in the tank is finished, the “ ” light remains steady on to indicate that the selector switch must be turned back to the “ ” position. MAX 10 Rinse the tank thoroughly and refill it with fresh drinking water. 11 Empty the container used to collect the liquid dispensed by the machine.
• 16 • CONTROL PANEL LIGHTS Light Signals Steady on Slowly flashing Quickly flashing Slowly flashing Causes Solutions The machine has reached the right temperature and is now ready: - For coffee brewing; - For hot water dispensing; - For steam dispensing The machine is warming up to brew coffee and dispense hot water or steam. Machine is overheating. Coffee may not be brewed.
• 17 • Problems Causes The machine does not turn on. The machine is not connected to the power source. Solutions Connect the machine to the power source. The coffee is not hot enough. The cups are cold. Preheat the cups with hot water. Hot water or steam is not dispensed. The hole of the hot water / steam wand is clogged. Clean the hole of the hot water / steam wand using a pin. Make sure that the machine is turned off and has cooled before performing this operation.
• 18 •
English • 19 •