User manual

9
Unfreezing set time
1 Hold down the red O button while pressing ¢, £ and ¢ in succession.Then release the O button.The set time is no longer frozen.
2 Set a new tanning time and press the green I button to switch the lamps on.
Operating hour registration
1 Select • to set the time.
2 Set the time to 00.
3 Set the body cooler to position O.
4 Press the O button to display the operating hours.
◗ The maximum number of hours that can be displayed is 999.When this value has been reached, the counter will start counting up from
000 again.
5 When you release the O button, the number of operating hours disappears from the display.
Setting the menus
To enter the owner's menus, hold down the I button while pressing ¢, £, ¢, the O button, £ and ¢ in succession.Then release the I button.
B
C00 will appear on the display.
B
Press ¢ and £ to navigate through the menus.
Setting the operating hours (menu C01)
The standard setting is 400 hours.You can change this setting.The selection range is 150-750 hours.
1 Press the I button.
2 To increase the number of operating hours, press the O button.
◗ The step size is 50 hours.
◗ The display counts up to 750. If you continue to press the O button when 750 has been reached, the display will start counting up from
150 again.
3 Confirm the new setting by pressing the I button again.
Time setting menu (C02)
The default setting is 0, which means that users can adjust the tanning time between 0 to 24 minutes according to their own wishes.
1 Press the I button.
2 Press the O button once to select setting 1.This setting allows users to set the tanning time between 1 minute and a maximum time to
be set in menu C03.
3 Confirm the new setting by pressing the I button again.
◗ Users cannot set a tanning time that is longer than the maximum tanning time set, but they can set a shorter time.
B
Note: If you have selected setting 1 in menu C02 and have accidentally limited the tanning time to 1 minute in menu C03, users will not be able to
set a tanning time.
Setting maximum tanning time (menu C03)
This option is only available to you if you have selected setting 1 in menu C02.
1 Press the I button.
2 Hold down the O button to increase the time in minutes.
B
The display counts up to 40 (24 for the HB604/6000SX). If you continue to hold down the O button when 40 (24 for the HB604/6000SX) has
been reached, the display will start counting up from 1 again.
◗ Use this option to shorten the maximum settable tanning time for users.
3 Confirm the new setting by pressing the I button again.
Setting the cooling time (menu C04)
The default setting is 180 seconds.The selection range is 30-900 seconds.
1 Press the I button.
2 Hold down the O button to increase the time in seconds.
◗ The step size is 30 seconds.
B
The display counts up to 900. If you continue to hold down the O button when 900 has been reached, the display will start counting up from 30 again.
3 Confirm the new setting by pressing the I button again.
B
Note: As the facial tanner requires a cooling time of 180 seconds, we advise you not to set a shorter cooling time.
Retrieving software data (menu C05)
Select this menu to view the version number of the software.
B
You may need this information when you require service.
Resetting operating hour counter (menu C06)
When you are in this menu, press the O button to reset the operating hour counter.
B
This will remove the œ from the display.
'Facial-off blocking' function (C07)
The default setting is 0, which means that the 'facial-off blocking' function has not been activated. Confirm the new setting by pressing the
I button again.
ENGLISH