GC1830, GC1820, GC1815, GC1814, GC1730, GC1720, GC1711, GC1710, GC1705, GC1703, GC1702, GC1701 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 MAX 1 18
ENGLISH General description (Fig.
After the Calc-Clean process 1 Connect the iron to the mains to let the soleplate dry. 2 Unplug the iron when the temperature light has gone out. 3 Move the iron gently over a piece of used cloth to remove any water stains that may have formed on the soleplate. Problem Cause Solution Water leaks from the soleplate during ironing. The iron is not hot enough. Set the temperature dial to a temperature suitable for steam ironing ( 2 to MAX).
简体中文 一般说明 (图 1) A 喷雾嘴 (GC1830/1820/1815/1814/1730/1 720/1705) B 加水口 C - 蒸汽控制 - x = 除水垢功能 喷雾按钮 T (GC1830/1820/1815/1814/17 30/1720/1705) 蒸汽喷射 9 (GC1830/1820/1815/1814) 自动关熄指示灯(仅限 GC1830) 温度指示灯 电源线 防水垢片(仅限 GC1830/1820/1730) 型号牌 水箱 温度旋钮 D E F G H I J K L O.
蒸汽和沸水会从底板冲出。水垢(如果有的话)也 一并冲出。 8 使用除水垢功能之后,按下蒸汽控制旋钮同时 将其旋转至 O 的位置。 如果从熨斗中冲出的水仍有水垢颗粒,则应再次使 用除水垢功能。 完成除水垢过程后 1 插上熨斗的插头,让底板变干。 2 当温度指示灯熄灭时,拔下熨斗的电源插头。 问题 原因 解决方法 自动关熄指示 灯闪烁(仅限 GC1830)。 自动关熄 功能已 启动( 见“功 能”一 章)。 提起熨斗或轻轻移 动以取消自动关熄 功能。自动关熄指 示灯熄灭。 当熨斗冷却或 存放后,水从 底板漏出。 熨斗水平 放置时水 箱中还有 水。 存放熨斗之前,先 将水箱倒空,然 后将蒸汽控制设定 到 O 位置(见“存 放”一章)。将熨 斗竖立存放。 蒸汽喷射功能 或垂直蒸汽喷 射功能不起作 用(仅限特定 型号)。 在短时间 内频繁使 用(垂 直)蒸汽 喷射功 能。 将熨斗平放,稍等 片刻后再使用( 垂直)蒸汽喷射功 能。 熨斗不够 热。 将温度转盘设定在 一个适合蒸汽熨烫 的温度( 3 到 最大)。将熨斗竖 立,直到温度指示 灯熄灭后再开始熨 烫。 3 将熨斗放在一块用过的布上轻轻
GC1730, GC1720, GC1711, GC1710, GC1705, GC1703, GC1702, GC1701 2007/01/18 423900061493 6/6