Mini Hi-Fi System pg 001-024_FWM185-79_Eng 1 FWM185 2007.4.
CAUTION Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. pg 001-024_FWM185-79_Eng 2 2007.4.
7 2 4 ( 3 ¡ £ ) 8 $ * % ≤ ! ≤ 5 ™ ™ 0 4 2 1 5 % ! * 6 9 @ 7 ^ # & 3 pg 001-024_FWM185-79_Eng 3 2007.4.
Contents English General Information Tape Operation/Recording Supplied accessories ............................................ 5 Environmental Information ................................ 5 Safety information ................................................ 5 Tape playback ...................................................... 13 General information on recording ................. 13 Synchro start CD recording ............................ 13 Recording from the radio .................................
Supplied accessories – 2 speaker boxes – remote control – MW loop antenna Environmental Information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet). Your system consists of materials which can be recycled and reused if disassembled by a specialized company.
Preparations English FM ANT LOOP ANT 8 LOW CH – + L R L R HIGH CH B Speakers Connection Rear connections The type plate is located at the rear of the system. A Power – Before connecting the AC power cord to the wall outlet, ensure that all other connections have been made. WARNING! – For optimal performance, use only the original power cable. – Never make or change any connections with the power switched on. – High voltage! Do not open.You run the risk of getting an electric shock.
2 C Antenna Connection Connect the supplied MW loop antenna to the respective terminal. Adjust the position of the antenna for optimal reception. English Preparations Use a USB cable (not supplied) to connect the socket on the set. card reader into the Connecting a non-USB device Use a cinch cable to connect MP3 PLAYER IN to the analogue audio out terminals of an external equipment (TV, VCR, Laser Disc player, DVD player or CD Recorder).
Controls (illustrations on page 3) English Controls on the system and remote control 1 LCD Display – shows the status of the system. infrared sensor for remote control. 3 PROG – – adjusts the volume level. – sets the hours and minutes for the clock and timer. ^ MP3 PLAYER IN 2 iR SENSOR – % VOLUME 3/4 – RECORD 0 ....... starts recording. PLAY 2 ................. starts playback. REW à /F.FWD á fast rewinds/ forwards the tape. STOP•OPEN 9/ stops the tape; opens the tape compartment. PAUSEÅ ......
IMPORTANT: Before you operate the system, complete the preparation procedures. Switching the system on ● Press STANDBY-ON y. ➜ The system will switch to the last selected source. English Basic Functions 2 Press DBB to switch bass enhancement on or off. ➜ Display shows: DBB if the DBB is activated. 3 Press DSC on the remote control repeatedly to select the desired sound effect: OPTIMAL, JAZZ, ROCK or TECHNO. ➜ The selected DSC is shown.
CD/MP3/WMA Operation English 5 To pause playback press 2;. Press 2; again to resume play. ➜ The display freezes and the elapsed playing time flashes when playback is interrupted. 6 To stop disc playback, press STOP 9. Note: CD playback will also stop when; – the CD door is opened. – the disc has reached the end. – you select another source: TAPE, TUNER, USB or MP3 IN. – you select standby. Selecting a different track IMPORTANT: The lens of the CD player should never be touched.
Discs for playback Programming track numbers This system can playback all digital audio CD, finalised digital audio CD-Recordable (CDR) discs and finalised digital audio CD-Rewritable (CDRW)discs. MP3-CDs (CD-ROMs with MP3 tracks) Programme in the STOP position to select and store your disc tracks in the desired sequence. If you like, store any track more than once. Up to 20 tracks can be stored in the memory. 1 In the STOP position, press PROG on the remote control to enter the programming mode.
Radio Reception English Tuning to radio stations 1 Press SOURCE once or more to select TUNER. 2 Press BAND once or more to select desired waveband: MW, FM MONO or FM ST (stereo). 3 Adjust the TUNING control knob to tune to a desired radio frequency. Note: – The system is equipped with an external MW antenna and a fixed FM antenna. For optimal MW reception, adjust the position of the MW loop antenna until the strongest signal is found.
English Tape Operation / Recording General information on recording IMPORTANT! – Before playing a tape, check and tighten slack tape with a pencil. Slack tape may get jammed or may burst in the mechanism. – C-120 tape is extremely thin and is easily deformed or damaged. It is not recommended for use in this system. – Store the tapes at room temperature and do not put them too close to a magnetic field (for example, a transformer,TV or speaker).
Tape Operation / Recording English To select and record a particular passage within a CD track: ● Press and hold down on REW à or F.FWD á. Release the control when you recognize the passage you want. ● To interrupt CD playback press 2; . ● Recording starts from this exact point in the track when you press RECORD 0. 6 To pause, press PAUSE Å. Press PAUSE Å again to resume. 7 To stop recording, press STOP•OPENÇç.
Using a USB mass storage device By connecting a USB mass storage device to the Hi-Fi system, you can enjoy the device's stored music through the powerful speakers of Hi-Fi system. Compatible USB mass storage devices With the Hi-Fi system, you can use: – USB flash memory (USB 2.0 or USB1.1) – USB flash players (USB 2.0 or USB1.
External Sources English How to organize your MP3/WMA files on the USB mass storage device This Hi-Fi system will browse the MP3/WMA files in the folders/sub-folders/titles order. Example: 3 Play the USB's audio files as you do with the albums/tracks on a CD (See CD/MP3/WMA Operations). Notes: – For compatibility reasons, the album/track information may differ from what it is displayed through flash players' music management software.
English Clock/Timer Setting the clock Setting the sleep timer 1 In standby mode, press and hold CLOCK. ➜ The clock digits for the hours flash. The sleep timer enables the system to switch off by itself after a set period of time. 2 Adjust the VOLUME control knob or press VOLUME 3/4 on the remote control to set the hours. 3 Press CLOCK. ➜ The clock digits for the minutes flash. 4 Adjust the VOLUME control knob or press VOLUME 3/4 on the remote control to set the minutes.
Clock/Timer English Setting the timer ● The system can switch on to CD, TUNER, or USB mode automatically at a preset time, serving as an alarm to wake you up. IMPORTANT! – Before setting the timer, ensure that the clock is set correctly. – The timer will always be switched on after it has been set. – The timer will not start if a recording is in progress.
AMPLIFIER 1 KHz (Low channel - both channels driven) ................................................... 30 W per channel (8 Ω) 10 KHz (High channel - both channels driven) ................................................... 30 W per channel (8 Ω) Total output power ............................................... 120 W Signal-to-noise ratio .......................... ≥ 62 dBA (IEC) Frequency response ......... 63 – 16000 Hz, ± 3 dB CD PLAYER Frequency range ..................................
Maintenance English Cleaning the Cabinet ● Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasives. Cleaning Discs ● When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the centre out. ● Do not use solvents such as benzene, thinner, commercially available cleaners, or antistatic spray intended for analogue records.
WARNING Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. Do not open the system as there is a risk of electric shock. If a fault occurs, first check the points listed below before taking the system for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre. Problem Solution CD OPERATION “No disc” is displayed. – Insert a disc. – Check if the disc is inserted upside down.
Troubleshooting English The remote control does not function The timer is not working. The Clock/Timer setting is erased. – Reduce the distance between the remote control and the system. – Insert the batteries with their polarities (+/– signs) aligned as indicated. – Replace the batteries. – Point the remote control directly toward IR sensor on the front of the system. – Set the clock correctly. – Press TIMER/SLEEP in standby mode to switch on the timer.
AUSTRALIA - Philips Manufacturers Warranty for Australia only These warranty conditions are valid for the following consumer electronics products: Colour Televisions, Projection TV, Plasma & LCD TV, Video Cassette Recorders, CD Recorders & Players, DVD Players, DVD Recorders, DVD Recorders with HDD, Audio Systems, Home Theatre systems, Digital Set Top Box & Portable Audio products.
NEW ZEALAND - Guarantee and Service for New Zealand Thank-you for purchasing this quality Philips product. Philips New Zealand Ltd guarantees this product against defective components and faulty workmanship for a period of 12 months. Any defect in materials or workmanship occurring within 12 months from the date of purchase subject to the following conditions will be rectified free of charge by the retailer from whom this product was purchased. Conditions 1.
Meet Philips at the Internet http://www.philips.com English Español Español Português Français Deutsch Nederlands Italiano Svenska FWM185 Dansk Suomi CLASS 1 LASER PRODUCT Português Polski Printed in China PageBack_FWM185 94 PDCC-LL-0710 2007.3.
