INTELLISTRIPE 380 USB/RS-232 DESKTOP MOTORIZED READER-ENCODER TECHNICAL REFERENCE MANUAL Manual Part Number 99875275-4 AUGUST 2010 REGISTERED TO ISO 9001:2008 1710 Apollo Court Seal Beach, CA 90740 Phone: (562) 546-6400 FAX: (562) 546-6301 Technical Support: (651) 415-6800 www.magtek.
Copyright© 2001-2010 MagTek®, Inc. Printed in the United States of America Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of MagTek, Inc. MagTek is a registered trademark of MagTek, Inc. IntelliStripe is a registered trademark of MagTek, Inc.
iii
SOFTWARE LICENSE AGREEMENT IMPORTANT: YOU SHOULD CAREFULLY READ ALL THE TERMS, CONDITIONS AND RESTRICTIONS OF THIS LICENSE AGREEMENT BEFORE INSTALLING THE SOFTWARE PACKAGE. YOUR INSTALLATION OF THE SOFTWARE PACKAGE PRESUMES YOUR ACCEPTANCE OF THE TERMS, CONDITIONS, AND RESTRICTIONS CONTAINED IN THIS AGREEMENT. IF YOU DO NOT AGREE WITH THESE TERMS, CONDITIONS, AND RESTRICTIONS, PROMPTLY RETURN THE SOFTWARE PACKAGE AND ASSOCIATED DOCUMENTATION TO THE ABOVE ADDRESS, ATTENTION: CUSTOMER SUPPORT.
FCC WARNING STATEMENT This equipment has been tested and was found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference with radio communications.
TABLE OF CONTENTS SECTION 1. FEATURES AND SPECIFICATIONS .................................................................................... 1 CONFIGURATIONS ................................................................................................................................. 1 FEATURES ............................................................................................................................................... 1 APPLICABLE DOCUMENTS .............................................
OPERATION ........................................................................................................................................... 17 PREVENTIVE MAINTENANCE .............................................................................................................. 17 CORRECTIVE MAINTENANCE ............................................................................................................. 17 Ejector Rod for Card Jams ............................................................
Figure 1-1.
SECTION 1. FEATURES AND SPECIFICATIONS The IntelliStripe® 380, Desktop Motorized Reader-Encoder reads and encodes magnetic-stripe cards and smartcards. CONFIGURATIONS Part numbers and descriptions for the basic configuration are as follows: 16050408 IntelliStripe 380 16050410 IntelliStripe 380, Magstripe Only 16051417 I/O Cable, 10-pin RJ45 connector connects to host 9-pin connector with 12V/Ground connector for Power Supply.
IntelliStripe 380 USB/RS-232 APPLICABLE DOCUMENTS Standards ISO 7811-2, -3, -4, -5 ISO 7810 ISO 7816 EMV 1996 EMV 2000 Identification cards tracks 1-3 Physical specifications Smartcard specifications Europay-Mastercard-Visa 1996 Level I Specification Europay-Mastercard-Visa 2000 Level I Specification MagTek Documents MCP Serial Transport Protocol, P/N 99875163 IntelliStripe 380, Command Reference Manual, P/N 99875217 SOFTWARE ACCESSORIES The following Software Modules may be required and will assist in t
Section 1. Features and Specifications Lead-in Roller System The primary purpose of the Lead-in Roller System is to grab the card from the user during card insertion and to make sure the card is mechanically under motor control before reaching the read/write head and its associated drive rollers. As a secondary function, the Lead-in Drive Roller will also assist in allowing for a more reliable exit positioning of the card during an eject sequence.
IntelliStripe 380 USB/RS-232 Ability To Transport 0.010 ”to 0.035” Cards Cards that meet the ISO 7810 card thickness of 0.027” to 0.033 will work properly with both magnetic and smartcard elements of this system. However, card thickness of 0.010” to 0.035” should not be expected to work properly in regard to magnetic and smartcard operations. These cards only need be successfully transported without jamming in the Reader.
Section 1. Features and Specifications Encoded Formats: In addition to encoding cards that comply with ISO 7811 encoding formats, it is possible to customize encoding formats as follows: • • • Encoded bit density is selectable at 75 or 210 bpi on all three tracks. The character is selectable for either 5-bit or 7-bit format on all three tracks. The Start-Sentinel character is user selectable as either a (;) or a (=) for 5-bit code or a (%) or (=) for 7-bit code.
IntelliStripe 380 USB/RS-232 Tamper Resistant Security Module (TRSM), Optional The unit provides mechanical and electromechanical features that allow the enclosure to be used within a TRSM environment per ISO 9564. Mechanical features visually indicate intrusion into the enclosure, and electromechanical switches on the Main PCB signal that the mechanical enclosure had been opened. This allows the electronics to erase the keys in its memory area whether the unit is powered or not.
Section 1. Features and Specifications Power Input The Reader/Encoder is powered by a 12 VDC power-pack. The +12 VDC power is carried to the Reader/Encoder as part of the Host Serial cable. All other voltages required by the Main PCB are generated onboard as required. The input connector and cabling carry power to support the Reader/Encoder.
IntelliStripe 380 USB/RS-232 Microcontroller LED Indicator The Main PCB supports a “watchdog” LED, which blinks on and off providing visual indication that the microcontroller is in a normal state of operation. The LED can be viewed when the bottom access hatch is removed from the enclosure. External Auto-Ranging Power Pack The Reader/Encoder is powered from an external power-pack, which is located near the Host Computer System. Power is routed to the Reader/Encoder through the Host RS-232 cable.
Section 1. Features and Specifications SPECIFICATIONS The Specifications are listed in Table 1-1. Table 1.1.
IntelliStripe 380 USB/RS-232 10
SECTION 2. INSTALLATION The installation of the IntelliStripe 380 Reader-Encoder consists of mounting the unit on a flat surface, connecting the I/O RS-232 cable to the host serial port, the Auxiliary cable to a peripheral device, and the Power Supply to the I/O cable and to a wall receptacle. MOUNTING The bottom of the unit is shown in Figure 2-1 and 2-2. The IntelliStripe 380 may be mounted in one of three ways: 1) foot pads, 2) set of mounting holes for 3 screws (4 x 40), and 3) 4 lock-inplace slots.
IntelliStripe 380 USB/RS-232 Figure 2-1. Dimensions for Mounting Holes for 3-Screw Set and Foot Pads Figure 2-2. Dimensions for Mounting Holes for Lock-in-Place Slots REAR PANEL AND CABLE CONNECTIONS To access the rear panel and cable connections on the IntelliStripe 380, remove the rear panel cover, shown in Figure 2-3, by squeezing the two mounting clips on the cover as indicated in the illustration.
Section 2. Installation Figure 2-3. Rear Panel and Cover Connect the Host PC cable (P/N 16051417) to the RS-232 connector on the IntelliStripe 380 as shown in Figure 2-4 for the RS-232 connection. Connect the Host PC Cable to the PC. Connect the Power Supply Cord (part of P/N 64300091) to the Host PC cable. Connect the North American 100-240v power cord (P/N 71100001) to the power supply. Caution Do not plug the power supply into a wall receptacle yet.
IntelliStripe 380 USB/RS-232 Figure 2-4. Cable Connections - RS-232 Table 2-1 lists the pins for the host cable P/N 16051417. Table 2-1. Pin List for IntelliStripe 380 to Host PC Cable P/N 16051417 10P10C RJ Plug 14 2.
Section 2. Installation Cable connections for the USB are Shown in Figure 2-5, and the pin lists are shown in Table 2-2 and Table 2-3. Figure 2-5. Cable Connections - USB Table 2-2.
IntelliStripe 380 USB/RS-232 Table 2-3. Cable Connections – USB Power P3 – 2.5 mm Power Jack Shell Gnd Center Pin +12 Shell Gnd Center Pin +12 Center Pin +12 Wire Color Drain Wire 26AWG Wire (Black) Braid Shield 26AWG Wire (Brown) 26AWG Wire (Red) P4 – 10P10C RJ Plug 1 PWR GND 2 +12 6 PWR GND 8 +12 10 +12 Check all connectors to ensure they are properly connected.
SECTION 3. OPERATION AND MAINTENANCE The operation of the unit includes inserting and removing the card. Maintenance includes keeping the unit clean and removing jammed cards from the unit. OPERATION The card is inserted with the magnetic stripe down and to the right as illustrated in Figure 3-1. Perform any tasks on the PC as directed. The LED gives status or direction as defined by the institution. Figure 3-1.
IntelliStripe 380 USB/RS-232 1. Remove the Rear Panel Cover to access the Ejector Rod as indicated in Figure 3-2. Figure 3-2. Ejector Rod Removal from Storage 2. Look into the Hole for Card Removal in the back of the unit, shown in Figure 3-2, to see the jammed card. This will indicate the approximate position where the notch on the Ejector Rod will be positioned with respect to the card. 3.
APPENDIX A. DIMENSIONS FOR MOUNTING MOUNTING The bottom of the unit is shown in Figure 2-1 and 2-2. The IntelliStripe 380 may be mounted in one of three ways: 1) foot pads, 2) set of mounting holes for 3 screws (4 x 40), and 3) 4 lock-inplace slots. The mounting dimensions of the 3 screw holes and the 4 lock-in-place slots are shown in Figure A-1. Footpad Mounting The footpads are mounted at the factory if it is the default.
IntelliStripe 380 USB/RS-232 Figure A-1.
Appendix A. Dimensions for Mounting Figure A-2.
IntelliStripe 380 USB/RS-232 Figure A-3.
Appendix A. Dimensions for Mounting Figure A-4.
