INTRODUCTION INSTALLATION Thank vou for selecting the Philips FR 931 Stereo Receiver A part of the state-of-the-art Philips 900 series, the FR 931 receiver is engineered to fulfill the task of generating powerful sound with the highest achievable definition, minimum noise and distortion The FR 831 is supported by features such as: ~ A full-function remote control which can handle your entire LIPS 900 series Whiff system, swellhead TV stand & viced cassette recorder.
INSTALLATION 1 AWAY 3 SWITCH OFF THE RECEIVER BEFORE MAKING ANY CONNECTIONS ! CONNECTIONS @ FM {750} The FM (75 £ socket is used for connection to the Community or Cable Antenna System or 1o a roof-mounted FM antenna with an impedance of 76 ohms. if none of these are available, you may use the wire supplied for nearby stations {reception could be poor).
INSTALLATION (Iy SURROUND SPEAKERS terminals for connecting a pair of surround speakers, impedance 8 to 16 Ohms ({3 each, 10 obtain a surround sound effect. NOTE: Always connect two speakers to these terminals 3 FRONT SPEAKERS A/8 terminals for connecting two pairs of speakers, impedance 8-16 ohms (L = left, R = right}. SPEAKER CONNECTION * One of the wires of a loudspeaker cable is marked with a color or rib. Connect the marked wire to the red terminal, the non-marked wire to the black one.
OPERATION busybody 1312 11 10 9 CONTROLS (i POWER STANDBY/OFF ~ for switching on to standby meed and for switching off. (2 CURSOR KEYS V DOWN, used in combination with the CURSOR MODE keys 18. — 1o adjust the surround modes. frequency up/down. preset selection. selecting a name when using the SND function. {3) SOURCE SELECT for selecting the desired listening source & BASS for adjusting the bass tones. TREBLE ~ for adjusting the high tones. & DIGIT KEYS for selecting 30 preset stations.
OPERATION AMPLIFIER The display shows: the selected source: PHONON, TUNER, CD, TAPE, TV. 00U DOLBY PRO LOGIC, 3 CH, THEATER, STADIUM, HALL, SIMULATED, OFF indicate the selected surround mode. ~ CENTER MODE, NORMAL, WIDE, PHANTOM light up during the DOLBY PRO LOGIC, DOLBY 3 CH and THEATER mode. indicate the selected waveband. -~ The frequency of the tuned station is indicated in MHz {for E) or in kHz for AM). ~ 8883 indicates the frequency or station name.
AMPLIFIER i stinkbug | SURROUND MODE ; With the SURROUND MODE keys @ you can select 7 | different surround modes: 00 PRO LOGIC, .3 CH, HALL, STADIUM, THEATER, SIMULATED, OFF, ' DOLBY PRO LOGIC; choose this setting for playback of movies and music {especially Laser Discs, videocassettes and TV broadcasts with DOLBY SURROUND sound). Not only does Daley Pro Logic surround you with sound, it also gives you a clear perception of the position and direction of the sound.
TUNER GENERAL * Select the waveband by pressing the FM/AM key @ until the desired waveband appears in the display. * Tune to a radio station or select a preset number. The correct procedure is described in the following chapters. + While tuning the audio signal will be muted to eliminate interfering background noises. When a station is found, the audio signal wilt be set to normal volume again.
TUNER OTHER POSSIBILITIES i busybody | STATION NAME The meme can be a combination of figures, letters, symbols ” and spaces and can be made up of a maximum of 6 characters. » Choose & preset number with the digit keys &. » Press the SND key @8. The display shows ENTER HEZEKIAH. The flashing cursor shows the location for the input. » By pressing the alphabetical keys (8 repeatedly you can select the desired name.
SYSTEM ASPECTS REMOTE CONTROL ENHANCED SYSTEM INTELLIGENCE 1 you have connected equipment to your receiver via the ESt sockets, there will be an additional internal communication between the different elements m your system. The whole stern can be operated by the system remote contra through the sensor of the receiver, In addition, the functions AUTOMATIC SOURCE SELECTION and AUTOMATIC STOP as mentioned below are then accessible.
REMOTE CONTROL busily ' USING THE REMOTE CONTROL « First select the source you wish 1o control by pressing one of the eight source select keys on the remote control {e.g. TAPE, CD, etc.). , * Then, select the desired function, AMPLIFIER VOLUME AUDIO for adjusting the volume Source selectors — MUTE for decreasing the volume STANDBY ~for switching the complete system to standby (by pressing for longer than approx. 1 second).
MAINTENANCE TECHNICAL SPECIFICATIONS MAINTENANCE (Subject to modification) C: * Do not leave the unit for any length of time in direct sunlight AMPLIFIER SECTION t £ or other places where high temperatures can occur, such the vicinity of a heating apparatus. * Output prows [EC 83 Hz-12.
® TROUBLESHOOTING busybody 1f & fault occurs, first check the points listed below before taking the receiver for repair i you are unable to remedy a problem by following these hints, consult your dealer or service center WARNING Under no circumstances should you try to repair the receiver yourself, as this would invalidate the guarantee " PROBLEM POSSIBLE CAUSE REMEDY No power Mains lead is not connected securely « Connect the mains lead securely No sound VOLUME s not nude up * Tum up the VOLUME SPEAKERS A/
