INTRODUCTION INSTALLATION Thank you for selecting the Philips FR 752 Stereo Receiver, WARNING A part of the state-of-the-art Philips 700 series, the FR 752 .
INSTALLATION stinkbug ; You only have to install your system once. Please make the following connections whenever applicable). NOTES! SWITCH OFF THE RECEIVER BEFORE MAKING ANY CONNECTIONS. Important note for connecting equipment that does not | have PLAY/REC markings on the input and output sockets: R kRl oY1 not connect the et to the mains when making FR752 Device to be connected e.9. cassette deck. connections.
F CENTER SPEAKER Terminals for connecting a center speaker. G FRONT SPEAKERS A/B Terminals for connecting two pairs of speakers, impedance 6-16 ohms (L = left, R = right}. * One of the wires of a loudspeaker cable is marked with a color or rib, Connect the marked wire to the red terminal, the nor-marked wire (o the black one. Make sure that all loudspeakers are connected in the same way.
FUNCTIONAL OVERVIEW FRONT 1 POWER ON/STANDBY For switching on to last mode and for switching off. 2 A SPEAKERS B A For switching on and off a pair of speakers connected 1o the SPEAKER A terminals. B~ For switching on and off a pair of speakers connected to the SPEAKER B terminals. 3 PROGRAM Four storing preset stations. 4 SURROUND For selecting the surround modes: DOLBY PRO LOGIC, DOLBY 3 STEREO, HALL, OFF. Dolby Surround manufactured under incense from Dolby Laboratories Licensing Corporation.
FUNCTIONAL OVERVIEW DISPLAY REMOTE CONTROL STEREO TUNED AUTO YCR 12 :;TREAS Horologic erectile HALL SLEEP (i DOLBY PRO LOGIC, 3-STEREO, HALL Indicates the selected surround mode. MHz kHz o The frequency of the tuned station is indicated in MHz for kHz {for AM). @ 8685858 ¢ X « indicates the station frequency and the selected AM/FM 15— 4 waveband, Indicates the DISPLAY MODE information in RDS mode. ] A + Indicates the AF information: in RDS mode. indicates the PTY information in RDS mode.
FUNCTIONAL OVERVIEW busybody 14 » 1 15—{8 178 AMPLIFIER 1 STANDBY for switching to standby. 4 VOLUME+VOLUME-~ for adjusting the volume 14 Source defectors 17 MUTE for muting the volume. 19 SLEEP for setting a time period after which the system will automatically be switched to standby Surround processor ARREARS LEVEL /- for adjusting the rear level.
AMPLIFIER POWER STANDBY/OFF ~ The receiver will enter to the last mode. STANDBY Switching a single source {e.g. CD) to standby » Press the STANDBY key briefly. The selected source will be switched to standby. canceled, Wake-up from standby * Press the POWER/STANDBY button to switch on the power. When the receiver is switched to active mode {as described below in the chapters 'Wake-up from standby' and 'SOURCE SELECTION'}, the respective indicators light up and the standby indicator is switched off.
AMPLIFIER ysnbuy DOLBY 3-STEREO: Choose this setting for playback of movies and music {especially Laser Discs, videocassettes and TV broadcasts with DOLBY SURROUND sound), when not using rear speakers. You get a clear perception of the position and direction of the sound.
TUNER ‘[ GENERAL * Tune to a radio station or select a preset number. * Select the waveband by pressing the FM or the AM key, or the TUNER button on the remote control. 5 The correct procedure is described in the following chapters. remote control, ~ While tuning, the audio signal will be muted to eliminate interfering background noises. When a station is found, the audio signal will be set to normal volunteer again. ~ When STEREO appears in the display, you are receiving an FM-stereo transmission.
TUNER OTHER POSSIBILITIES | Tuning buggy AUTOMATIC TUNING + Press TUNING/PRESET 1o switch off the preset indicator. + Press UP or DOWN for more than 1 second. “ — AUTO appears on the display. The tuner will now search until a station of sufficient strength has been found. The display shows the tuned frequency. * if the station found is not the desired one, simply repeat this operation, — Weak stations are skipped during automatic tuning. They can be tuned to manually.
ADDITIONAL INFORMATION MAINTENANCE T * Do not leave the unit for any length of time in direct sunlight or other places where high temperatures can occur, such as in the vicinity of a heating apparatus. + [0 not expose the equipment to humidity or rain, * Chamois leather cloth, slightly moistened with water is sufficient for cleaning the cabinet. * Do not use cleaning agents containing alcohol, spirits, ammonia or abrasives.
TROUBLESHOOTING busybody [f & fault occurs, run through the points listed below before taking your receiver for repair. l if the fault remains, try o clear it by switching the receiver off and on again. If this also fails 10 help, consult your dealer.
FR 752 Dolby Pro logic AV Receiver BE Meet Philips at the internet 9007018640 Printed in Korea TClext/CvB/3631
