INTRODUCTION INSTALLATION Thank you for selecting the Philips FR 751 Stereo Receiver. POSITIONING YOUR SYSTEM A part of the state-of-the-art Philips 700 series, the FR 761 he uni e is shown receiver is engineered to fulfill the task of generating powerful stack the units of your system is show sound with the highest achievable definition, minimum noise .
INSTALLATION You only have to install your system once. Please make the following connections (whenever applicable}. NOTES! SWITCH OFF THE RECEIVER BEFORE MAKING ANY CONNECTIONS, Do not connect the set to the mains when making connections. — Be sure to connect the white plugs to the L {left) and the red plugs to the R right} sockets when making connections. Important note for connecting equipment that does not have PLAY/REC markings on the input and output caskets: ER761 Device to be connected e.g.
INSTALLATION F CENTER SPEAKER Terminals for connecting a center speaker. FRONT SPEAKERS A/B Terminals for connecting two pairs of speakers, impedance 618 ohms {L = left, R = right). » One of the wires of a loudspeaker cable is marked with a color or rib. Connect the marked wire to the red terminal, the non-marked wire to the black ong. Make sure that all loudspeakers are connected in the slime way.
FUNCTIONAL OVERVIEW FRONT 1 2 POWER ON/STANDBY For switching on to standby mode and for switching off. A SPEAKERS B A~ For switching on and off & pair speakers connected to the SPEAKER A terminals. 8 For switching on and off 3 pair speakers connected te the SPEAKER B terminals. PROGRAM For storing preset stations. SURROUND For selecting the surround modes: DOLBY PRO LOGIC, DOLBY 3 STEREO, HALL, OFF Dolby Surround manufactured under license from Dolby Laboratories Licensing Corporation.
FUNCTIONAL OVERVIEW DISPLAY DOLBY PRO LOGIC, DOLBY 3-STEREO, HALL Indicate the selected surround mode. FN, AM Indicate the selected waveband. The frequency of the tuned station s indicated in MHz tor FiM) or in kHz {for AM). Indicates the station frequency. VOL» « » Show the settings of volume, bass, treble and balance. AUTO Lights up when operating auto tuning or auto presetting. MUTE Lights up when the MUTE button on the remote control is pressed.
FUNCTIONAL OVERVIEW 7 ¥ i AMPLIFIER 1 STANDBY for switching the complete system to standby {by pressing for longer than approx.
AMPLIFIER POWER STANDBY/OFF STANDBY Switching a single source {e.g. CD} to standby * Press the STANDBY key briefly. The selected source will be switched to standby. Switching the whole system to standby = The whole system will be switched o standby. be canceled. Wake-up from standby * Press the POWER/STANDBY button to switch on the power. The receiver will enter the standby mode and the standby indicator will fight up.
AMPLIFIER broadcasts with DOLBY SURROUND sound), when not using rear speakers. You get a clear perception of the position and direction of the sound. DOLBY 3-STEREO combines the front and rear signals so that you can enjoy a regenerated sound field which has comparatively more presence and a more expansive feeling from the three front channels {front left, front right and center speakers} than that of ordinary stereo regeneration.
TUNER GENERAL * Tune 1o & redo station or select a preset number, demote control. A stereo station can be stored in mono or in stereo. * Select the waveband by pressing the FM or the AM key, or the TUNER button on the remote control. The correct procedure is described in the following chapters. ~ While tuning, the audio signal will be muted to eliminates interfering background noises. When a station is found, the audio signal will be set to normal volume again.
OTHER POSSIBILITIES ADDITIONAL INFORMATION usqfiug SLEEP The sleep timer can be used to set a time period after which you wish your system & be switched 1o standby mode, » Press the SLEEP key on the remote control. * The display shows the indication SLEEP 70, This means that the system will be switched to standby after 10 minutes. * Select the required sleep time by pressing SLEEP: minutes. Notes: During an active sleep timer period, you can reset the dime to SLEEP 10 again by pressing the SLEEP key.
TROUBLESHOOTING if a fault recurs, run through the points listed below before taking your receiver for repair. if the fault remains, try to clear it by switching the receiver off and on again. if this also fails to help, consult your dealer. Under no circumstances should you repair the receiver yourself as this will invalidate the guarantee! PROBLEM PRESET STATIONS CANNOT BE RECEIVED ~ POSSIBLE CAUSE An incorrect station frequency has been memorized. * REMEDY * Memorize the correct station frequency.
Australia @ New Zealand GUARANTEE FOR AUSTRALIA The benefits given to the purchaser by this warranty are in addition to all other rights and remedies, which, under the Trade Practices Act or other Commonwealth or State law, the purchaser or owner has in respect of the product. The Philips product carries the following warranties: C-series WiFi-systerns 12 months. Compact Disc Players: 12 months. — Home Audio Systems: 8 months.
