INTRODUCTION INSTALLATION Thank you for selecting the Philips FR 732 Stereo Receiver.
INSTALLATION stinkbug 1 You only have to install your system once. Important note for connecting equipment that does not | The FM (76 Q) socket is used for connection 1o the Community or Cable Antenna System or to a roof-mourned FM antenna with an impedance of 75 ohms. If none of these are available, you may use the supplied wire for nearby stations reception could be poor}.
INSTALLATION SPEAKER POSITIONING FRONT SPEAKERS To obtain the best surround sound effect in your home, place fi Tarring for connecting a pair of speakers, impedance 6-16 the speakers as shown below. B ohms (L = left, The left and right speakers should be about 1 m {40°} from the ‘,fi * One of the wires of a loudspeaker cable is marked with a TV set, [ color or rib. Connect the marked wire o the red terminal, The center speaker should be above or below the TV set. n— the non-marked wire to the black one.
FUNCTIONAL OVERVIEW i ladybug FRONT 1 POWER ON/STANDBY For switching on to standby mode and for switching off. 2 SPEAKERS ON/OFF For switching the speakers connected to the FRONT SPEAKERS terminals on and off. 3 PROGRAM For storing preset stations. 4 SURROUND For selecting the surround modes: DOLBY PRO LOGIC, DOLBY 3-STEREO, OFF Dolby Surround manufactured under license from Dolby Laboratories. Licensing Corporation.
FUNCTIONAL OVERVIEW Dis Play DOLBY PRO LOGIC, DOLBY 3-STEREO Indicates the selected surround mode. Fiv, AM indicates the selected waveband. The frequency of the tuned station is indicated in MHz (for FM) or in kHz (for AM}. 88588 Indicates the station frequency. Vole levee Show volume, bass, treble and balance settings. AUTO Lights up when operating auto tuning.
FUNCTIONAL OVERVIEW stinkbug AMPLIFIER 1 STANDBY for switching to standby. 4 VOLUME + ~ for adjusting the volume. 14 Source selectors 17 MUTE for muting the volume. 19 SLEEP for setting a time period after which the system will automatically be switched t¢ standby. Surround processor . ARREARS LEVEL for adjusting the rear level {only in Dolby Pro Logic mode). 12 TEST TONE for checking the output level of the front, center and rear speakers.
AMPLIFIER STANDBY Switching a single source {e.g. CD) to standby « Press the STANDBY key briefly. The selected source will be switched to standby. Wake-up from standby and ‘SOURCE SELECTION'), the respective indicators light up and the standby indicator is switched off. » To switch the receiver off press the POWER/STANDBY key again, » Select the source using the source keys on the remote control. * Press POWER/STANDBY on the receiver or select a source with your remote control.
AMPLIFIER DOLBY 3-STEREO: Choose this setting to play back movies and raucous {especially Laser Discs, video cassettes and TV 3 ) broadcasts with DOLBY SURROUND sound), when not using the rear speakers.
TUNER GENERAL * Tune to a radio station or select a preset number. remote control, A stereo station can be stored in mono or in stereo. » Select the waveband by pressing the FM or the AM button or press the TUNER button on the remote control. The correct procedure is described in the following chapters. While tuning, the audio signal will be muted to eliminate interfering background noises. Once a station is found, the audio signal will be set to normal volunteer again.
OTHER POSSIBILITIES ADDITIONAL INFORMATION i SLEEP ysyfiug The sleep timer can be used to set a time period after which you wish your system 1o be switched to standby made. + Press the SLEEP key on the remote control. The display shows the indication SLEEP 10. ~ This means that the system will be switched 1o standby after 10 minutes. « Select the required sleep teems by pressing SLEEP: minutes, Notes: ~ During an active sleep timer period, you can reset the time to SLEEP again by pressing the SLEEP key.
TROUBLESHOOTING If & fault accursed, run through the points listed below before taking your receiver for repair, if the fault persists, attempt 1o salve it by switching the receiver off and on again. |f this fails to resolve the situation, consult % your dealer. Under no circumstances should you repair the receiver yourself as this will invalidate the guarantee! & < o PROBLEM PRESET STATIONS CANNOT BE RECEIVED -~ POSSIBLE CAUSE An incorrect station frequency has been memorized.
