Philips 140S Electronic User's Manual file:///E|/Potomac/english/140S/index.
Safety & Troubleshooting Safety and Troubleshooting Information Safety Precautions and Maintenance • Installation Locations • Correct Handling of the LCD Monitor • FAQs • Troubleshooting • Regulatory Information • Other Related Information Safety precautions and maintenance WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards, and/or mechanical hazards.
Safety & Troubleshooting ● falling within the following temperature and humidity ranges. ❍ Temperature: 5-35°C 41-95°F ❍ Humidity: 20-80% RH Do not subject the LCD monitor to severe vibration or high impact conditions. Do not place the LCD monitor inside a car trunk. ● Take care not to mishandle this product by either knocking or dropping during operation or transportation. ● Do not store or use the LCD monitor in locations exposed to high humidity or a dusty environment.
Safety & Troubleshooting 4. When moving the monitor, be sure to unplug all power cords in order to avoid injury or damage to the equipment. RETURN TO TOP OF THE PAGE file:///E|/Potomac/english/140S/safety/safety.
About This Electronic User's Manual About This Electronic User's Manual About This Guide • Other Documents You May Need • Notational Descriptions About This Guide This electronic user's guide is intended for anyone who uses the Philips 140S LCD Monitor. It describes the LCD monitor's features, setup, operation and other pertinent information. Its contents are identical to the information in our printed version.
About This Electronic User's Manual Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold or italic type. These blocks contain notes, cautions, or warnings. They are used as follows: NOTE: This icon indicates important information and tips that help you make better use of your computer system. CAUTION: This icon indicates information that tells you how to avoid either potential damage to hardware or loss of data.
140S Product Information Product Information Product Features • Technical Specifications • Resolution & Preset Modes • Philips Pixel Defect Policy • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views Product Features 140S ● 14.1" color LCD monitor with excellent display performance and viewing size comparable to a 15" CRT monitor. ● ● 165mm depth with cable management, less than 60% foot print of comparable CRT monitors.
140S Product Information • Input signal levels 700m Vpp • Sync input signal Separate sync Composite sync • Sync polarities Positive and negative • Input Frequency XGA Hsync SVGA Hsync VGA Hsync • Video interface Analog (D-Sub) 48- 60 KHz, Vsync 60 - 75 Hz (N.I.) 35- 50 KHz, Vsync 56 - 75 Hz (N.I.) 31- 38 KHz, Vsync 60 - 75 Hz (N.I.) OPTICAL CHARACTERISTICS • Contrast ratio 200 (typ.) • Brightness 200 nits (typ.) • Peak contrast angle 6 o'clock • White Chromacity x: 0.281 y: 0.
140S Product Information dot rate (MHz) H. freq (KHz) Mode Resolution V. freq (KHz) 25.175 31.469 IBM VGA 10h 640*350 70.086 28.322 31.469 IBM VGA 3h 720*400 70.087 25.175 31.469 IBM VGA 12h 640*480 59.940 30.200 35.000 MACINTOSH 640*480 67.000 31.500 37.861 VESA 640*480 72.809 31.500 37.500 VESA 640*480 75.000 36.000 35.156 VESA 800*600 56.250 40.000 37.879 VESA 800*600 60.317 50.000 48.077 VESA 800*600 72.188 49.500 46.875 VESA 800*600 75.000 57.
140S Product Information This monitor is ENERGY STAR® compliant. As an ENERGY STAR® Partner, PHILIPS has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. RETURN TO TOP OF THE PAGE Physical Specifications • Dimension (WxHxD) 361 x 343 x 165 mm (incl. Pedestal) • Weight 4.
140S Product Information 3 Blue video input 11 Identical output - connected to pin 10 4 Identical output - connected to pin 10 12 Serial data line (SDA) 5 6 7 Self test Red video ground Green video ground 13 14 15 H. Sync / H+V V. Sync (VCLK for DDC) Data clock line (SCL) 8 Blue video ground RETURN TO TOP OF THE PAGE Views Follow the links to see various views of the monitor and its components.
Installing your LCD Monitor Installing your LCD Monitor Your LCD Monitor : Front View Product Description • Connecting to Your PC • Getting Started • Optimizing Performance Front View UP and DOWN buttons are used when adjusting the OSD of your monitor LEFT and RIGHT buttons, like the UP and DOWN buttons, are also used in adjusting the OSD of your monitor. file:///E|/Potomac/english/140S/install/install.
Installing your LCD Monitor BRIGHTNESS hotkey. When the UP and DOWN arrow buttons are pressed, the adjustment controls for the BRIGHTNESS will show up. .OK button which when pressed will take you to the OSD controls POWER button switches your monitor on Automatically adjust the horizontal position, vertical position, phase and clock setting.
On-Screen Display On-Screen Display Description of the On-Screen Display • The OSD Tree • The OSD Controls Description of the On Screen Display What is the On-Screen Display? This is a feature in all Philips LCD monitors which allows an end-user to adjust screen performance of monitors directly though an on-screen instruction window. The user interface provides user-friendliness and ease-of-use when operating the monitor. Basic and simple instruction on the control keys.
On-Screen Display RETURN TO TOP OF THE PAGE The OSD Tree Below is an overall view of the structure of the On-Screen Display. You can use this as reference when you want to later on work your way around the different adjustments. file:///E|/Potomac/english/140S/osd/osddesc.
On-Screen Display RETURN TO TOP OF THE PAGE file:///E|/Potomac/english/140S/osd/osddesc.
On-Screen Display file:///E|/Potomac/english/140S/osd/osddesc.
Customer Care and Warranty Customer Care & Warranty PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR WARRANTY COVERAGE WESTERN EUROPE: Austria • Belgium • Cyprus • Denmark • France • Germany • Greece • Finland • Ireland • Italy • Luxembourg • the Netherlands • Norway • Portugal • Sweden • Switzerland • Spain • United Kingdom EASTERN EUROPE: Czech Republic • Hungary • Poland • Russia • Turkey LATIN AMERICA: Antilles • Argentina • Brasil • Chile • Colombia • Mexico • Paraguay • Peru • Uruguay • Vene
Glossary Glossary ABCDEFGHIJKLMNOPQRSTUVWXYZ C Color temperature A way of describing the color of a radiating source in terms of the temperature (in degrees Kelvin) of a black body radiating with the same dominant frequency as the source. Most Philips monitors offer the possibility of setting the color temperature to any desired value. RETURN TO TOP OF THE PAGE D D-SUB Your monitor comes with a D-Sub cable.
Glossary L LCD Liquid Crystal Display An alphanumeric display using the unique properties of liquid crystal to form characters. The latest flat-panel displays comprise a matrix of hundreds or thousands of individual LCD cells that generate text and colorful graphics on a screen. They consume little power though they do require external lighting to make them legible to the user.
Download and Print Download and Print Download and Printing Instructions • Installing FPadjust Program • Installing your LCD monitor driver This page provides an option to read the manual in .pdf format. PDF files can be downloaded into your hard disk, then viewed and printed with Acrobat Reader or through your browser. If you do not have Adobe¨ Acrobat Reader installed, click on the link to install the application. Adobe® Acrobat Reader for PC / Adobe® Acrobat Reader for Mac.
Download and Print CONTRAST, BRIGHTNESS, HORIZONTAL & VERTICAL POSITION, PHASE and CLOCK. System requirements: ● PC running Window 95, Window 98 or later To install FPadjust Program: ● ● Click on the link or icon to install FPadjustment Program. or Click-and-hold your mouse over the icon. (Win95/98 users right-click) Download FPadjust (SETUP.EXE) ● From the menu that appears, choose 'Save Link As...', 'Save Target As...' or 'Download Link to Disk'.
Download and Print ● 'source', choose 'source'). Exit your browser and install the .inf/.icm file. NOTE: ● Read the " ReadMe.txt" file before installing . ● You may be required to restart your PC once the driver installed. RETURN TO TOP OF THE PAGE file:///E|/Potomac/english/download/download.
FAQs (Frequently Asked Questions) FAQs (Frequently Asked Questions) Safety and Troubleshooting • General FAQ • Screen Adjustments • Compatibility with Other Peripherals • LCD Panel Technology • Ergonomics, Ecology, and Safety Standards • Troubleshooting • Regulatory Information • Other Related Information General FAQs Q: When I install my monitor how do I do if the screen shows "Cannot display this video mode"? A: Recommended video mode for Philips 150P/150B/140S: 1024x768 @60Hz for Philips 181AS 1280x102
FAQs (Frequently Asked Questions) A: Your video card/graphic driver and monitor together determine the available resolutions. You can select desired resolution under Window 95/98 with the "Display properties/Settings" control panel Q: What if I get lost when making monitor adjustments? A: Simply press the OSD button, then select "Reset" to recall all original settings.
FAQs (Frequently Asked Questions) Q: How should I clean the LCD surface? A: For normal cleaning, use the clean, soft and fine. For extensive cleaning, please use Isopropyl alcohol. Do not use other solvents such as ethyl alcohol, ethanol, acetone, hexane, etc. Q: What accessories are available for my 150P / 181AS LCD monitor? A: Currently there are 3 accessories available for the 150P.
FAQs (Frequently Asked Questions) Screen Adjustments Q: What is CustoMax® and what models are compatible? (181AS / 150P) A: CustoMax® is proprietary Philips software that allows users to adjust monitor via software instead of control keys under Windows base. With the Philips Brilliance 150P, CustoMax® operates via a USB connection to PC. All Philips 150P models are CustoMax® compatible, but your computer must support USB in order to use CustoMax®.
FAQs (Frequently Asked Questions) Q: How can I adjust the screen? A: The screen brightness may be adjusted using the Brightness control in the OSD. Scaling an image in this manner results in slight brightness "fuzziness" or distortion. RETURN TO TOP OF THE PAGE Compatibility with other Peripherals Q: Can I connect my LCD monitor to any PC, workstation or Mac? A: Yes, all Philips LCD monitors are fully compatible with standard PC, Mac and workstation.
FAQs (Frequently Asked Questions) RETURN TO TOP OF THE PAGE LCD Panel Technology Q: What is Liquid Crystal Display? A: A Liquid Crystal Display (LCD) is an optical device that is commonly used to display ASCII characters and images on digital items such as watches, calculators, portable game consoles etc. LCD is the technology used for displays in notebook and other small computers.
FAQs (Frequently Asked Questions) Q: How does a TFT LCD Panel work? A: On each column and row of the TFT LCD panel, a data source drive and a gate drive and attached respectively. The TFT drain of each cell is connected to the electrode. The molecular arrangement of liquid crystal elements differs depending on whether it is impressed with voltage or not. It varies the direction of polarized light and the amount of light by letting it through different arrays of liquid crystal elements.
FAQs (Frequently Asked Questions) Q: Why is there no flicker on an LCD Monitor? A: Technically speaking, LCDs do flicker, but the cause of the phenomenon is different from that of CRT monitor -- and has no impact of ease of viewing. Flickering in a LCD monitor refers to usually undetectable luminance caused by the difference between positive and negative voltage. On the other hand, CRT flickering that can irritate the human eye comes when the on/off action of the florescent object becomes visible.
FAQs (Frequently Asked Questions) RETURN TO TOP OF THE PAGE file:///E|/Potomac/english/140S/safety/saf_faq.
Troubleshooting Troubleshooting Safety and Troubleshooting • FAQs • Common Problems • Imaging Problems • Regulatory Information • Other Related Information This page presents problems that can be corrected by the user. If the problem still exists after these possible solutions, contact your nearest Philips dealer. Common Problems Having this problem? No Picture (Power LED not lit) Check these items ● Make sure the Power cable is plugged to the wall and the Adapter of the monitor.
Troubleshooting ● The Auto Function is designed for use on standard Macintosh or IBM-compatible PC running Microsoft properly Windows. ● It may not work properly if using non-standard PCs or video card. ● Push the Auto button. Adjust the image position using the Horizontal Position &/or Vertical Position in the second Window AUTO button not working properly Imaging Problems Display position is incorrect ● ● Check that the signal cable is properly connected to the graphics board or PC.
Troubleshooting ● If an image remains in the screen for an extended period of time, it may be imprinted in the screen and leave an after-image. This usually disappears after a few hours ● This is characteristic of liquid crystal and is not caused by a malfunction or deterioration of the liquid crystal. The after-image will disappear after a set amount of time ● The remaining dots are normal charactericstic of the liquid crystal used in today’s technology.
Regulatory Information Regulatory Information TCO'92 and TCO '99 Information • TCO Environmental Requirements • Energy Star Declaration • Federal Communications Commission (FCC) Notice (U.S.
Regulatory Information Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs.
Regulatory Information We recommend you switch off the monitor when it is not in use for quite a long time. RETURN TO TOP OF THE PAGE Federal Communications Commission (FCC) Notice (U.S. Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Regulatory Information EN 55022 Compliance (Czech Republic Only) RETURN TO TOP OF THE PAGE VCCI Notice (Japan Only) This is a Class B product based on the standard of the Voluntary Control Council for Interference (VCCI) for Information technology equipment. If this equipment is used near a radio or television receiver in a domestic environment, it may cause radio Interference. Install and use the equipment according to the instruction manual.
Regulatory Information A protection mark "B" confirms that the equipment is in compliance with the protection usage requirements of standards PN-93/T-42107 and PN-89/E-06251. RETURN TO TOP OF THE PAGE North Europe Information Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE.
Regulatory Information BCIQ Notice (Taiwan Only) RETURN TO TOP OF THE PAGE Ergonomie Hinweis (nur Deutschland) Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor Schäden durch Röntgenstrahlen" festgelegten Vorschriften. Auf der Rückwand des Gerätes befindet sich ein Aufkleber, der auf die Unbedenklichkeit der Inbetriebnahme hinweist, da die Vorschriften über die Bauart von Störstrahlern nach Anlage III ¤ 5 Abs. 4 der Röntgenverordnung erfüllt sind.
Regulatory Information 3-pin plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5A. Note: The severed plug must be destroyed to avoid a possible shock hazard should it be inserted into a 13A socket elsewhere.
Other Related Information Other Related Information Safety and Troubleshooting • FAQs • Troubleshooting • Regulatory Information • Information for Users in the U. S. • Information for Users Outside the U.S Information for Users in the U. S. For units set at 115 V : Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a maximum of 15-feet long and a parallel blade, grounding type attachment plug rated 15 A, 125 V.
Philips Pixel Defect Policy Philips Pixel Defect Policy Product Features • Technical Specifications • Resolution & Preset Modes • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views Philips' Flat Panel Monitors Pixel Defect Policy Philips strives to deliver the highest quality products. We use some of the industry's most advanced manufacturing processes and practice stringent quality control.
Philips Pixel Defect Policy One lit red, green or blue subpixel Two adjacent lit subpixels: Three adjacent lit subpixels (one - Red + Blue = Purple white pixel) - Red + Green = Yellow - Green + Blue = Cyan (Light Blue) Black Dot Defects Black dot defects appear as pixels or subpixels that are always dark or "off".
Philips Pixel Defect Policy RETURN TO TOP OF THE PAGE file:///E|/Potomac/english/140S/product/pixel.
Connecting to Your PC Connecting to Your PC Your LCD Monitor : Front View Product Description • Accessory Pack • Connecting to Your PC • Getting Started • Optimizing Performance Accessory Pack Unpack all the parts. 1) Power Cable (socket may differ for different countries) 2) Macintosh Adapter (optional) 3) E-DFU package with Quick Setup Guide, Using Your Monitor Manual, and CD-ROM. 4) AC / DC Adaptor. file:///E|/Potomac/english/140S/install/connect.
Connecting to Your PC RETURN TO TOP OF THE PAGE Connecting to Your PC 1) To remove the back cover, simply press the 2 clips on its underside, then pull out and down. 2) Remove the plastic ring from the hinge file:///E|/Potomac/english/140S/install/connect.
Connecting to Your PC 3) Plug in DC power cable into the DC connector. 4) Cover the cables with the plastic ring and put the ring back on the hinge NOTE: If you use an Apple Macintosh™, you need to connect the special Mac adapter to one end of the monitor signal cable file:///E|/Potomac/english/140S/install/connect.
Connecting to Your PC 5) Replace the back cover on the monitor file:///E|/Potomac/english/140S/install/connect.
Connecting to Your PC 6) Connect to Your PC 6.1 Turn off your computer and unplug its power cable. 6.2 Connect the monitor signal cable to the video connector on the back of your computer. 6.3 Connect the audio, microphone and USB to the ports on the back of your computer, if any. 6.4 Plug the power cord of your computer and your monitor into a nearby outlet. 6.5 Turn on your computer and monitor. If the monitor displays an image, installation is complete.
Getting Started Getting Started Your LCD Monitor : Front View Product Description • Connecting to Your PC • Getting Started • Optimizing Performance Getting Started 1.1 First turn on your monitor and other peripherals if any, then turn on your computer. 1.2 If your monitor displays an image and Windows prompts you for an .inf file or driver disk, please go to step 1.4. 1.
The OSD Controls The OSD Controls Description of the On-Screen Display • The OSD Tree The OSD Controls : Brightness (HotKey) • Language • Adjust Position • Brightness and Contrast • Video Noise • Adjust Color • OSD Settings • Product Information • Reset to Factory Settings • Close Main Controls BRIGHTNESS Brightness is the overall intensity of the light coming from the screen. To adjust your screen's brightness, follow the steps below. An 80% brightness is recommended.
The OSD Controls LANGUAGE The ON SCREEN DISPLAY prompts can be in one of six languages. The default language is English, but you can select French, Spanish, German, Italian, or Japanese. 1) Press the button on the monitor. The MAIN CONTROLS window appears. LANGUAGE is highlighted. (If not, press the or button on the monitor until LANGUAGE is highlighted) 2) Press the button again. The LANGUAGE window appears.
The OSD Controls Smart Help After returning to MAIN CONTROLS… Smart Help … to continue to ADJUST POSITION, press the button until ADJUST POSITION is highlighted. Next, follow steps 3 - 6 under ADJUST POSITION. … to exit completely, press the button. RETURN TO TOP OF THE PAGE ADJUST POSITION ADJUST POSITION is composed of two steps, ADJUST HORIZONTAL and ADJUST VERTICAL. ADJUST HORIZONTAL shifts the image on your screen either left or right.
The OSD Controls 3) Press the button. The ADJUST POSITION window appears. ADJUST HORIZONTAL is highlighted. 4) Press the or 5) Press the button until ADJUST VERTICAL is highlighted. Press the button to move the image left or right until it appears centered. or button to move the image up or down until it appears centered. 6) Press the button to confirm your selections and return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS is highlighted.
The OSD Controls RETURN TO TOP OF THE PAGE BRIGHTNESS & CONTRAST BRIGHTNESS & CONTRAST is composed of two steps, BRIGHTNESS and CONTRAST. Brightness is the overall intensity of the light coming from the screen. An 80% brightness is recommended. Contrast is the difference between the light and dark areas on the screen. A 50% contrast is recommended. To adjust the Brightness and Contrast, follow the steps below. Note: Brightness can also be adjusted without using the MAIN CONTROLS window.
The OSD Controls 5) When finished with BRIGHTNESS, press the or 6) Press the button until CONTRAST is highlighted. Next, press the button to adjust the contrast. A 100% contrast is recommended. button to confirm your selection and return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS is highlighted. Smart Help After returning to MAIN CONTROLS… Smart Help … to continue to VIDEO NOISE, press the button until VIDEO NOISE is highlighted. Next, follow steps 3 - 6 under VIDEO NOISE.
The OSD Controls highlighted. 2) Press the button until VIDEO NOISE is highlighted. 3) Press the button. The VIDEO NOISE window appears. PHASE is highlighted. 4) Press the or button to adjust the phase. 5) When finished with PHASE, press the button until CLOCK is highlighted. Next, press the button to adjust the clock. file:///E|/Potomac/english/140S/osd/osd_cont.
The OSD Controls 6) Press the button to confirm your selection and return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS is highlighted. Smart Help After returning to MAIN CONTROLS… Smart Help … to continue to ADJUST COLOR, press the button until ADJUST COLOR is highlighted. Next, start with step 3 under ADJUST COLOR and follow the directions. … to exit completely, press the button.
The OSD Controls 3) Press the button. The ADJUST COLOR window appears. 4) Press the or button to select ORIGINAL PANEL COLOR, 9300K FOR CAD/CAM, 6500K FOR IMAGE MANAGEMENT, or USER PRESET. file:///E|/Potomac/english/140S/osd/osd_cont.
The OSD Controls 5) Once you have highlighted ORIGINAL PANEL COLOR, 9300K FOR CAD/CAM, or 6500K FOR IMAGE MANAGEMENT, press the button to confirm your selection and return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS is highlighted. 6.1) If USER PRESET is highlighted, press the button to highlight RED. Next, press the button to adjust the color red. file:///E|/Potomac/english/140S/osd/osd_cont.
The OSD Controls 6.2) When finished with RED, press the button to highlight GREEN. Next, press the or button to adjust the color green. 6.3) When finished with GREEN, press the button to highlight BLUE. Next, press the or button to adjust the color blue. button to confirm your adjustments and return to 6.4) When all adjustments are complete, press the the MAIN CONTROLS window. CLOSE MAIN CONTROLS is highlighted.
The OSD Controls 1) Press the button on the monitor. The MAIN CONTROLS window appears. LANGUAGE is highlighted. 2) Press the button until OSD SETTINGS is highlighted. 3) Press the button. The OSD SETTINGS window appears. HORIZONTAL is highlighted. 4) Press the or 5) Press the button until VERTICAL is highlighted. Press the button to move the MAIN CONTROLS window left or right to the desired position. CONTROLS window up or down to the desired position.
The OSD Controls 6) Press the button to confirm your selections and return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS is highlighted. Smart Help After returning to MAIN CONTROLS… Smart Help … to continue to PRODUCT INFORMATION, press the button until PRODUCT INFORMATION is highlighted. Next, start with step 3 under PRODUCT INFORMATION and follow the directions. … to exit completely, press the button.
The OSD Controls 3) Press the button. The PRODUCT INFORMATION window appears. This window shows the monitor's SERIAL NUMBER and RESOLUTION of the monitor. 4) Press the button to return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS is highlighted. Smart Help After returning to MAIN CONTROLS… Smart Help … to continue to RESET TO FACTORY SETTINGS, press the button until RESET TO FACTORY SETTINGS is highlighted. Next, start with step 3 under RESET TO FACTORY SETTINGS and follow the directions.
The OSD Controls RESET TO FACTORY SETTINGS returns everything in all the windows to factory presets. This means all adjustments that you may have made will be returned to the original settings. 1) Press the OK button on the monitor. The MAIN CONTROLS window appears. LANGUAGE is highlighted. 2) Press the button until RESET TO FACTORY SETTINGS is highlighted. 3) Press the button. The RESET TO FACTORY SETTINGS window appears. 4) Press the or button to select YES or NO. NO is the default.
The OSD Controls RETURN TO TOP OF THE PAGE Close Main Controls RETURN TO TOP OF THE PAGE file:///E|/Potomac/english/140S/osd/osd_cont.
F1rst Choice Warranty Your International Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact Philips directly to benefit from your Philips F1rst Choice Warranty.
International Guarantee Your International Guarantee Dear Customer, Thank you for purchasing this Philips product which has been designed and manufactured to the highest quality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement parts irrespective of the country where it is repaired during a period of 12 months from date of purchase.
United States Guarantee LIMITED WARRANTY (Computer Monitor) Three Years Free Labor / Three Years Free Service on Parts / One Year Exchange* *Product will be exchanged with a new or renewed to original specifications unit within two business days for the first year. This product must be shipped in at your expense for service during years two and three. WHO IS COVERED? You must have proof of purchase to receive warranty service.
United States Guarantee Philips service organization will attempt to provide service (although there may be a delay if the appropriate spare parts and technical manual(s) are not readily available). Where CAN I GET MORE INFORMATION? For more information, contact the Philips Customer Care Center by calling (877) 835-1838 (U.S.A. customers only) or (903) 242-4804. Before Requesting Service... Please check your owner's manual before requesting service.
United States Guarantee Philips Customer Care Center, P. O. Box 2976, Longview, TX 75601 Your International Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact Philips directly to benefit from your Philips F1rst Choice Warranty.
