English pegged Figures page Guarantees and service pages 80,9192 Francis page 11t Figures page Quarantine et service aprons-vents pages 909182 Putsch Semite 21 Abbildungen Semite 86,87,88,89 Guaranteeing und Service Seiten90,91,92 Netherlands patina 32 Figure patina 86,87,88,89 Gantlet en service patina's 90,91,92 Lifespan angina 41 Graffias patinas 86,87,88,8% Niagara vaginas 90,9192 totalitarian paginate Figure patine 86,87 88.
Connection of loudspeakers, see Fig. 6; » Ensure that the uni is switched off {POWER’ switch () not pressed. » Select the loudspeaker to be connected (e.g. the left one, "L} * Put the marked wire in the red terminal 'L’, the non-marked wire in the black terminal 'L, * In exactly the same way connect the wires from the other loudspeaker (in this case the right one, 'R} with the two other terminals, L.e.
stairs interference caused by weak stereo reception is really reduced. in normal circumstances this bitten should be left in the "stereo” position (not pressed in). For the RIF function, see the section on "Recording’. "MISQUOTED MIX' terminate for a mono microphone. See under "Microphone resorting sound mix'.
by pressing “VOLUME UP' button {5} until the desired volume is reached. I you can hear nothing ~ Are the loudspeakers switched off by a headphone connected to socket 67 ~ Is the correct function selection button pressed in? |s the selected sound source working properly? volumetric A 'button pressed long enough? « Are the loudspeakers properly connected? When checking the loudspeakers, first switch off the unit! 4. Adjust the stereo balance using control @) &, Adjust the tone using the controls @. 6.
control unit. The frequency required, followed by the memory position, appears on the display. Signal suppression » During some operations the sound signal Is suppressed. This is to eliminate unwanted background noise, It recurs, for example, during tuning {tuning crackle. « "MUTE' button {3} of the remote control unit can be pressed &.g. during a telephone conversation. « The Mute operation is canceled: by pressing MUTE” button again, by pressing VOLUME UP’ button [5] until the desired volume fs reached.
» Thistledown during playback of the fast number, ERR' appears on the display to indicate that there is no following number and payback of the last number is continued, Selecting a previous number # Briefly press the bunion € until the desired number appears on the display.
Wis also possible to move from the firstborn to the last number by pressing the 4 SKIP/SEARCH’ button . PROGRAMMING Staring numbers in the memory General You can » store the numbers in random larder » only store each number once « store a maximum of 20 numbers « only store or alter a program when the disc is not moving. 1. Alter inserting the disc, press the 'OPEN/CLOSE" button &. The tray will close.
the VOLUME A" control @, or the bunions () and of the cremate control unt. Requite the balance using the 'BALANCE' contra @. Regulate the tone using the FIVE BAND EQ controls (3, 10. The record can be interrupted by moving lever @ o the X" position, The ratatouille wil continue to turn. To continue record playback, lever @ must be carefully moved to the "X” position, T1. At the end of the record the record player will automatically switch off and the arm rectums to its suppertime, 72.
8. To stop playback, press the "STOP/EJECT button or . 0. The recorder stops automatically during recording or playback when the end of the tape has been reached. Continuous playback 1. Select cassette playback by pressing the TAPE® button . 2. The HIGH SPEED DUBBING' button {3 must another pressed, 3. Open both cassette compartments by pressing the ‘STOP/EJECT button's @and placeholder cassettes in both compartments (see Fig. 4.
