English Figures Guarantees and service Francis Figures page 2 page 82,83,84,85 pages page 11 page 82,83,84,85 Quarantine et service aprons-vents pages 86,87,88 Putsch Armaments Abbildungen Guaranteeing und Service Netherlands Figure Quarantine en service Espalier Figures.
Connection of loudspeakers, see Fig. 6: # Ensure that the neuritis switched off CON/OFF switch {3) not pressed). When using two loudspeakers, use the terminals . When using four loudspeakers, use the terminals () for the front loudspeakers and use predetermination the rear loudspeakers, areas a second pair in anther room, # Tessie the loudspeaker o be connected (.g. the left one, L. « Puttee marked wire in the red terminal L, the.
{@ remote sensor receives the infra red signals from the remote control unit. ® sound level (A} and spectrum analyzer () display Shows the level and dynamic tonal distribution ova five frequency bands. display Lights up when switched on and shows # The sound sources: "Cd’ or 'Add’ Additional, for TVIVGR).
# 'PLAY’ Fer starting the tape transport for playback and rewording. * 'REWIND For fast rewinding the tape, * WIND® For fast forwarding the tape, » "STOP" To stop the tape transport. o "EJECT' To open the cassette compartment, cassette compartment for deck A @9 Indicator for the Dolby Noise Reduction system. @) Recording indicator Lights up during recording. @ counter {for deck A) with 'RESET’ button, The counter indicates how far the tape transport in sack A has advanced.
It no reaction is obtained and/or if nothing lights up Switchover stand switch the steno again after 2 faw seconds, ‘the units not {properly) connected to the main voltage, or ~ The plug socket s dead. 2. Press in the relevant function button @, e.g. 'SACS, 'PHONON, TUNER’, 'CD/CDV’, or "TV/ YCR’ and turn on the given source. 4 Hold button 'VOLUME UP' @ {or button [ of the cremate contra) pressed until the desired volume level is reached, Remark: "MUTE’ button{§] of the remote control unit can be pressed e.
the correct tuning range (FM/LW/MW) appears on the display. 2. Tune 1o the desired transmitter: # Pres button @ 'DOWN’ or @) 'UF° (or the buttons "SEARCH ' [s] or "SEARCH M [g]on the remote control unit} for more than 0.5 seconds. Then release this button, The frequency on the display now changes continuously until a transmitter of sufficient strength bas been found.
RECORD PLAYER (NOT ON ALL VERSIONS} 1. Place a record on the tum table. For records with a large center hole, use adapter disk & and reals this whilst at the same time touring it to the Left so that it remains in the raised position. In some models a separate adapter disk is supplied. 2. Remove the stylus protection cover by pulling it forwards gently. . 3. Set the appropriate sped, the rpm selector 6. 4. Se lest record player mode by pressing 'PHONON* button €3 5.
connected loudspeakers or headphones and/or be recorded on deck A, Note: # When a microphone is connected to socket (3), the sound even from another {stereo} sound source will always be recorded and reproduce din mono. « if you wish to use the unit as a microphone amplifier without mixing with another sound source, press the "TV/VCR' button &) and switch off the. record playback or other sound source connected 10 the "TY/VCR' terminals CASSETTE PLAYBACK 1.
Proceed as folios: 1. Press both 'EJECT' buttons and insert a recorded cassette info deck B and a cassette chichis lusted for recording into deck A (fig. 4). 2. Dubbing will start by pressing at the same time the buttons ‘PLAY” &) on deck B and 'REC’ + PLAY € on deck A 3. Misunderstood passages, prods 'PAUSE' @ on deck A; deck B wiki continue the playback. To restart copying, press "PAUSE’ @ once more. Using the "PAUSE’ button £ of deck B, deck A wiki record a blank part. 4.
