Super automatic espresso machine 4000 series EP4010 EN USER MANUAL 4219.460.3764.1 PHILIPS4000 CMF_FRONT-BACK_A5_WE.
1 2 6 CLASSIC COFFEE ESPRESSO 11 MEMO 3 4 7 AROMA STRENGTH ESPRESSO LUNGO STEAM/WATER 12 8 MENU 13 5 9 10 16 15 14 17 35 18 34 33 32 19 31 20 21 30 22 29 COFF EE 23 24 28 27 25 26
4 English Contents Machine overview_________________________________________________________________ Introduction ______________________________________________________________________ First installation___________________________________________________________________ AquaClean filter __________________________________________________________________ Activating the AquaClean filter_______________________________________________________ Replacing the AquaClean filter______________________________________
English 5 Machine overview 1 User interface 19 Cord 2 ESPRESSO button 20 Grind setting knob 3 ESPRESSO LUNGO button 21 Cover of bean hopper 4 STEAM/WATER button 22 Bean hopper 5 Standby button 23 Brew group 6 CLASSIC COFFEE button 24 Inside of service door with contact information 7 AROMA STRENGTH button 25 Coffee exit duct 8 MENU button 26 Coffee residues drawer 9 Classic milk frother 27 Coffee grounds container 10 Adjustable coffee dispensing spout 28 Drip tray cov
6 English - This is the QR code. Scan this code to access instruction videos on how to brew the best coffees, how to clean the machine and for a list of frequently asked questions. (www.philips.com/coffee-care) - The separate booklet with important safety information. First installation For first installation, follow the instructions on the separate quick start guide. Note: This machine has been tested with coffee. Although it has been carefully cleaned, there may be some coffee residues left.
English AQUA CLEAN FILTER 0/8 7 2 Press the MENU button, select MENU and press the OK button to confirm. Scroll to AQUACLEAN FILTER. Press the OK button to confirm. - The display shows the number of AquaClean filters that have been installed previously from 0 to 8 filters. 3 Select ON on the display, press the OK button to confirm. ON OFF 0/8 4 The display automatically updates the number of filters used.
8 English AQUA CLEAN FILTER 2/8 - The display automatically updates the number of filters used. 4 Dispense 2 cups of hot water (0.5 l) to complete the activation. Discard this water. Replacing the AquaClean filter after 8 filters were used 1 DESCALE BEFORE ACTIVATING FILTER When the filter icon starts flashing on the display, press the MENU button, scroll to AQUACLEAN FILTER and press the OK button to confirm.
English 9 Control panel and display This espresso machine has a self-explaining display for easy use. Read the sections below for a quick explanation of the buttons. One-touch beverage buttons Use the one-touch beverage buttons to quickly prepare one of the preset beverages: ESPRESSO, ESPRESSO LUNGO, STEAM/WATER and CLASSIC COFFEE. Navigation buttons Some of the one-touch beverage buttons have a double function; use these buttons to navigate through the menu.
10 English Before brewing beverages as described below, the lever must be in the right position: - Push the lever down to the ESPRESSO position to brew espresso or espresso lungo. - Push the lever up to the COFFEE position to brew classic coffee. Brewing coffee Brewing coffee with beans Caution: Only use espresso beans. Never put ground coffee, unroasted coffee beans or caramelized coffee beans in the bean hopper, as this may cause damage to the machine.
English 11 2 Pour one measuring scoop of pre-ground coffee into the pre-ground coffee compartment and close the lid. Caution: Do not put any other substance than pre-ground coffee in the pre-ground coffee compartment, as this may damage the machine. 3 Place a cup under the coffee dispensing spout. 4 Press the AROMA STRENGTH button and select the pre-ground coffee brewing function. 5 Press the ESPRESSO button. The machine automatically starts brewing the selected beverage.
English 12 Hot water Warning: Danger of scalding! Dispensing may be preceded by small jets of hot water. Use the appropriate protective handle only. 1 Place a jug under the classic milk frother. 2 Press the STEAM/WATER button. - The display shows HOT WATER. 3 Press the OK button to confirm. - The machine starts dispensing water. 4 To stop dispensing hot water, press the OK button.
English 13 Adjusting grinder settings You can adjust the grinder settings by using the grind setting knob inside the bean container. Note: You can only adjust the grind settings when the machine is grinding coffee beans. Caution: Do not turn the grind setting knob more than one notch at a time to prevent damage to the grinder. 1 Place a cup under the coffee dispensing spout. 2 Open the lid of the bean hopper. 3 Press the ESPRESSO button.
English 14 Part description When to clean How to clean Coffee grounds container When it suits you Empty the coffee grounds container and clean it under the tap. Make sure the machine is switched on while you empty and clean the coffee grounds container. Water tank When it suits you Clean it under the tap. Pre-ground coffee compartment/coffee exit duct Weekly Clean the top part with a spoon handle as shown below. Cleaning the brew group Note: Scan the QR code or visit www.philips.
English 15 5 Rinse the brew group thoroughly with lukewarm water. Clean the upper filter carefully. 6 Let the brew group air-dry. Note: Do not dry the brew group with a cloth to prevent fibers from collecting inside the brew group. Cleaning the brew group with coffee oil remover tablets Caution: Only use Philips/Saeco coffee oil remover tablets for cleaning. They do not have a descaling function. 1 Place a container under the coffee dispensing spout.
16 English - To position the hook correctly, push it upwards until it is in uppermost position. - The hook is not positioned correctly if it is still in bottommost position. 3 Slide the brew group back into the machine along the guiding rails on the sides until it locks into position with a click. Caution: Do not press the PUSH button. 4 Close the service door. Lubrication For optimal performance of the machine, you have to lubricate the brew group. See table below for the lubrication frequency.
English 17 Cleaning the classic milk frother After the last usage of the day 1 Remove the classic milk frother from the steam wand and rinse it with fresh water. 2 Clean the steam wand with a wet cloth. 3 Reassemble all the classic milk frother parts. Descaling procedure When the display shows START CALC CLEAN, you need to descale the machine. If you do not descale the machine when this message appears on the display, the machine will eventually stop working properly.
18 English 2 1 XAM CLAC C NAEL CALC CLEAN 5 Pour the descaling solution into the water tank. Fill the water tank with fresh water up to the CALC CLEAN level indication. Place the water tank back into the machine. Press the OK button to confirm. - The first phase of the descaling procedure starts. The machine starts dispensing the descaling solution at intervals. - The display shows the descaling icon, the phase indication and the duration. This first phase takes 20 minutes.
English 19 Warning icons and error codes Meaning of the warning icons ADD WATER ADD COFFEE 10 xx Fill the water tank with fresh water to the MAX level indication. The brew group is blocked by coffee powder. Clean the brew group. The bean hopper is empty. Put new coffee beans in the bean hopper. Insert the drip tray and close the service door. The brew group is not in the machine or it is not inserted correctly. Insert the brew group.
20 English Error code Problem Cause Possible solution The brew group is not Switch off the machine. Remove the positioned correctly. brew group and reinsert it. Make sure the two reference signs on the side match before you slide the brew group back into the machine (see 'Reinserting the brew group'). Then switch the machine on again. 05 There is a water circuit problem. There is air in the water circuit. Switch off the machine. Make sure you insert the water tank into the machine properly.
English Error code Problem Cause 21 Possible solution The brew group is not Switch off the machine. Remove the positioned correctly. brew group and reinsert it. Make sure the two reference signs on the side match before you slide the brew group back into the machine (see 'Reinserting the brew group'). Then switch the machine on again. 05 There is a water circuit problem. There is air in the water circuit. Switch off the machine. Make sure you insert the water tank into the machine properly.
22 English Problem Cause Solution The drip tray fills up quickly. This is normal. The machine uses water to rinse the internal circuit and brew group. Some water flows through the internal system directly into the drip tray. Empty the drip tray when the 'drip tray full' indicator pops up through the drip tray cover. Place a cup under the dispensing spout to collect rinsing water. The 'coffee grounds container full' icon remains displayed.
English 23 Problem Cause Solution The coffee exit duct is clogged. Clean the coffee exit duct with the handle of the measuring spoon or a spoon handle. Then switch the appliance off and on again. The cups you use are cold. Preheat the cups by rinsing them with hot water. The temperature is set too low. Check the menu settings. Set the temperature to 'high' in the menu. You added milk. Whether the milk you add is warm or cold, it always decreases the temperature of the coffee to some extent.
24 English Problem Cause Solution There is water under the machine. The drip tray is too full and has overflowed. Empty the drip tray when the 'drip tray full' indicator pops up through the drip tray. Always empty the drip tray before you start descaling the machine. The machine is not placed on a horizontal surface. Place the machine on a horizontal surface so that the 'drip tray full' indicator works properly. You have already replaced the AquaClean filter 8 times.
START DESCALING? 23 MIN empty page before backcover
www.philips.com/coffee-care 4219.460.3764.1 PHILIPS4000 CMF_FRONT-BACK_A5_WE.
