Specifications
3.Directions for use EN 9
DVP320
7
Preparation
Warning!
ñ Connec
t the DVD player directly to your
TV, instead of eg. a VCR, to avoid
distortion because DVD video discs are
copy protected.
ñ Do not connect the DVD player AUDIO
OUT to PHONO IN of your player.
ñ Set DIGITAL OUTPUT correctly. The
Stereo must support MPEG2 or Dolby
Digital
TM
.Check the Stereoís manual to be
sure.
Before you begin...
Refer to the instructions of your TV, VCR, Stereo,
or other devices. Note the style of jacks and
connectors on the other equipment. Determine
how to choose different Audio and Video In
channels/sources on your other equipment.
Disconnect all equipment from the power outlets.
Connect equipment to power only after hooking
up everything. Never make or change
connections with equipment connected to power.
Please refer to the below choices we introduce
to you and select either one of them.
Connecting to a TV with audio
and video cables
LR
A
U
D
I
O
V
I
D
E
O
COAXIAL VIDEO Y Pb Pr
MAINS
120V ~ 60HZ
Back of TV
(example only)
LEFT A UDIO IN
VIDEO IN
RIGHT A UDIO IN
LEFT AUDIO IN
VIDEO IN
RIGHT AUDIO IN
Connect the VIDEO jack on the DVD player to
the corresponding CVBS VIDEO IN jack on your
TV (cable supplied).
Connect the AUDIO OUT (Left/Right) on the
DVD player to the corresponding AUDIO IN
jacks on TV by using audio cable (supplied). Match
the cable colors to the jack colors.
Connecting to a TV with audio
cable and component video cable
LR
A
U
D
I
O
V
I
D
E
O
COAXIAL VIDEO Y Pb Pr
MAINS
120V ~ 60HZ
Back of TV
(example only)
LEFT
AUDIO IN
RIGHT
AUDIO IN
Pr/Cr
Y
Pb/Cb
RIGHT
AUDIO IN
LEFT
AUDIO IN Pr/Cr
Y
Pb/Cb
Co
nnect the Y/Pb/Pr VIDEO OUT on the DVD
player to the corresponding jack on your TV by
using component video cable (not supplied).
Match the cable colors to the jack colors.
Connect the AUDIO OUT (Left/Right) on the
DVD player to the corresponding AUDIO IN
jacks on TV by using audio cables (supplied).
Match the cables color to the jack colors.
Connecting to a TV and a two-
channel Stereo
VIDEO IN
Stereo
(example only)
Back of TV
(example only)
VIDEO IN
LEFT AUDIO IN
RIGHT AUDIO IN
LR
A
U
D
I
O
V
I
D
E
O
COAXIAL VIDEO Y Pb Pr
MAINS
120V ~ 60HZ
Connect the VIDEO jack on the DVD player to
the corresponding CVBS VIDEO IN jack on
your TV (cable supplied).
Connect the AUDIO OUT (Left/Right) on the
DVD player to the corresponding AUDIO IN
jacks on stereo system by using audio cables
(supplied). Match the cable colors to the jack
colors.
Connecting to a TV and a
Stereo
LR
A
U
D
I
O
V
I
D
E
O
COAXIAL VIDEO Y Pb Pr
MAINS
120V ~ 60HZ
VIDEO IN
Back of TV
(example only)
VIDEO IN
COAXIAL
DIGI T AL
AUDIO IN
AV Receiver
Connect the VIDEO OUT jack on the DVD
player to the corresponding VIDEO IN jack on
your TV by using composite video cable (cable
supplied) or component video cable (not
supplied).
Connect the COAXIAL jack of the DVD
player to the corresponding DIGITAL AUDIO
IN jack on your AV Receiver (cable not
supplied). In this case, do not use the player's
audio left and right output.
8
Preparation
Replacing battery (lithium
CR2025) into the remote control
1
Pull out the lithium battery
compartment.
2 Replace a new battery and fully insert
the battery compartment back to the
original position.
CAUTION!
ñ Insert the plastic protective sheet if they
are exhausted or not to be used for a long
time.
ñ Batteries contain chemical substances,
so they should be disposed off properly and
kept away from children.
Using the Remote Control
Pull out the plastic protective sheet
which is used to keep the lithium
battery fresh.
Direct the remote control at the
remote sensor of the DVD player.
Do not drop or give the remote
control a shock.
Do not leave the remote control in extremely
hot or humid places.
Do not spill water or put anything wet on the
remote control.
Connecting the Power Supply
1 Plug the female end of the power cable supplied
into the power connector on the rear of the
player.
2 Plug the male end of the cord into an AC outlet.
Note: When the DVD player is switched to
Standby mode, it is still consuming some power. If
you wish to disconnect your player completely from
the mains, withdraw the plug from the AC Outlet.
Switching On
1
Be sure that the DVD player has been correctly
connected to the TV and audio equipment.
2 Switch on the TV and DVD player.
3 Set the TV to the correct Video In channel. (eg.
EXT1, EXT2, AV1, AV2, AUDIO/VIDEO, etc.
Please refer to your TV owner's manual for
details.)
The player display lights and the default screen
appears on the TV.
4 If you are using an external equipment (eg. audio
system or receiver), turn it on and select the
appropriate input source for the DVD player
output. Refer to the equipment ownerís manual
for detail.
Smart Power On/Off
When in STOP or NO DISC mode, the DVD
player will switch to standby mode after 15
minutes without any operations for saving energy.
It is easily reactivated by pressing the POWER or
PLAY key on the remote control or the PLAY
button on the front panel.
About Progressive Scan
If your TV set has the Progressive Scan, please
connect the Y/Pb/Pr VIDEO OUT jacks on the
DVD player to the corresponding jacks on the TV
set with the component video cables (no
supplied). After connection, please activate the
PROGRESSIVE function of the DVD player. Refer
to the chapter Progressive Scan for more details.
Deactivating Progressive Scan
If you have activated the PROGRESSIVE function,
however, your TV set doesnít have the function
actually, or the component cable doesnít be
correctly connected, the TV set will not display
normally. You can deactivate the function as
follows:
1 Press the POWER button on the front panel to
turn on the DVD player.
2 Press OPEN/CLOSE to release the disc
compartment lid on top of the player.
3 Press the 1 , and then press the MUTE key.
DVD player will restore the interlace video
output.
LITHIUM BATTERY
DC
-- -
3V CR2025
CR202 5
+
+
3V
C
R
2
0
2
5
LITHIUM BATTERY
DC
-- -
3V CR2025