DVD Player DVP3156, DVP3160KˈDVP3166(K) DVP3160K/55/77/78 DVP3166/94,DVP3166X/94 DVP3166K/93 DVP3156/93 Service Service Manual TABLE OF CONTENTS Page . Technical Specifications……………………………………...................1-2 . Safety Instruction, Warning & Notes….……………………….....….....1-3 . Mechanical and Dismantling Instructions………….............................2-1 . Region Code, Software Version& Upgrades……………..................... 3-1 . . Trouble Shooting Chart………………………………………….……….. 4-1 . .
1-2 Technical Specifications TV standard (PAL/50Hz) Number of lines Playback (NTSC/60Hz) 625 Multi standard 525 (PAL/NTSC) 24bits, 192KHz fs 96kHz fs 48kHz fs 48kHz fs 44.1kHz fs 44.1kHz CD/ VCD Signal-Noise (1kHz) Dynamic Range (1kHz) Cross talk (1kHz) Distortion/Noise (1kHz) MPEG MP3 12 bit, 108MHz 0.
1-3 Safety instruction, Warning & Notes Safety instruction 1. General safety 2.Laser safety Safety regulations require that during a repair: . Connect the unit to the mains via an isolation transformer. . Replace safety components indicated by the symbol , only by components identical to the original ones. Any other component substitution (other than original type) may increase risk of fire or electrical shock hazard.
1-4 Warning 1.General 2. Laser . All ICs and many other semiconductors are susceptible to . The use of optical instruments with this product, will electrostatic discharges (ESD). Careless handing during increase eye hazard. repair can reduce life drastically. Make sure that, during . Only qualified service personnel may remove the cover repair, you are at the same potential as the mass of the or attempt to service this device, due to possible eye set by a wristband with resistance.
1-5 Notes Lead-Free requirement for service INDENTIFICATION: x Regardless of special logo (not always indicated) Use only original spare-parts listed in the Service-Manuals. Not listed standard-material (commodities) has to be purchased at external One must treat all sets from 1.1.2005 onwards, according next rules. companies. x Important note: In fact also products a little older can also be treated in this way as long as you avoid mixing solder-alloys (leaded/ lead-free).
2-1 Mechanical and Dismantling Instructions Dismantling Instruction The following guidelines show how to dismantle the player. Step1: Remove 5 screws around the Top Cover, then remove the Top Cover (Figure 1). Figure 1 Step2: If it is necessary to dismantle Loader or Front Panel, It should be remove the Front door assembly first. (Figure 2) Note: Make sure to operate gently otherwise the guider would be damaged.
2-2 Mechanical and Dismantling Instructions Dismantling Instruction Step3: If the tray can’t open in normal way, you can make it through the instruction as below (Figure 3). Note: Make sure to operate gently otherwise the guider would be damaged. Push the guider until the tray out. Make sure to operate gently to avoid damage happening. Figure 3 Step4: Dismantling Loader, disconnect the 3 connectors aiming in the below figure, and remove 1 screw around the Loader.
2-3 Mechanical and Dismantling Instructions Dismantling Instruction Step5: Dismantling Front Panel, disconnect the 3 connector, then release the snaps on the both sides of Front Panel and bottom cabinet , then gently pull the Panel out from the set.
2-4 Mechanical and Dismantling Instructions Dismantling Instruction Step6: Dismantling Main Board, first disconnect the connector, and then remove 4 screws. (Figure 8) CON 8 Figure 8 Step7: Remove the 2 screws on Power Board to dismantle the Power Board.
3-1 Software upgrade Preparation to upgrade software B. Read out the software versions to confirm upgrading 1) 1) Start the CD Burning software and create a new CD remote control. project (Data Disc) with the following setting: Label: DVP3XXX (No need the label name) File Name: DVPXXXX_XX.BIN 2) Press<1><3><7><9>button to check the software information. Power on the set and open the tray, then press <5><5> The software version and other information are display to check the File Name.
Trouble shooting chart 4-1 Remark: Trouble shooting chart for DVP3160K/XX Spindle motor does not move Motor no move Go Check the FFC connection No Correct connection between 24P and the loader. Yes Check whether No “AVCC” Check (+5V) voltage is normal. the AVCC power supply Yes Check whether laser voltage No (2V for VCD & 2.2V for DVD) Check/Replace Q6ǃQ5. on Collector of Q6 and Q5 Yes 1.Whether voltage on pin 112 of U2 varies between 0 and 3.3V (3.
4-2 The power can not be on or off Trouble shooting chart Remark: Trouble shooting chart for DVP3160K/XX The power can’t be on or off Go Check the power supply No on the power board is Repair the power board normal. Yes Check if the CON301 on the front board to CN5 on Yes No Check/Correct connection the decoder board is in good contact. Yes Whether the connection No to K301 is broken. Correct the connection Yes Whether there is 0V and 3.3V voltage difference on Pin 104 PCON of U2.
4-3 All output voltages on the power board is 0V or deviated. Trouble shooting chart Remark: Trouble shooting chart for DVP3160K/XX All output voltages on the power board is 0V or deviated Yes Check whether Yes Replace F1 F1 is blown No Check whether No Replace C4 if D1, D2, D3, D4 are normal. there is 300V on C4. Yes Check whether 100KHz oscillating signal on Pin6 of U1 No Check/ replace U1. U1(PIN 3 - RC waveform) U1(PIN 8 - Drain waveform) Yes Check if +5V, +12V, -12V and are short.
4-4 Trouble shooting chart Remark: Trouble shooting chart for DVP3160K/XX Disc cannot be read. Disc cannot be read. Yes No Check the FFC connection Check the loaded circuit between 24P and the loader. Yes 1.Check voltage on pin 112 of U2 varies Check whether there is laser No voltage (2V for VCD and 2.2V for between 0 and 3.3V: Æ3.3V for VCD Æ0V for DVD DVD) on Collector of Q6 &Q5 2.
4-5 Only DVD disc or only disc except DVD can be played Trouble shooting chart Remark: Trouble shooting chart for DVP3160K/XX Only DVD disc, or only disc except DVD can be Played. Go Check the FFC connection between 24pin and the loader. No Check the loaded circuit Yes Check laser voltage (2V) output on Collector of Q6, if pin 23 of No Check the solder status on U2 and peripheral components U2 is at low level. Yes Check whether there is voltage variance on pin 23 of U2.
4-6 Trouble shooting chart Remark: Trouble shooting chart for DVP3160K/XX No display on LEDD, and buttons do not work No display on LED, and buttons do not work Yes Check whether there is correct contact between CON301 and CN5 No Correct connection Yes Check VCC(+5v) voltage on the power and front board No Fix power supply board top a power supply for should electric circuit Yes Check there are CS, DATA and CLK signals on CON301 on the front board.
4-7 Trouble shooting chart Remark: Trouble shooting chart for DVP3160K/XX Distorted audio and loud noise Distorted audio and loud noise Yes Check the power supply voltages No +12V and -12V to the operation Check Q15 amplifying Q15 IS normal.
4-8 Trouble shooting chart Remark: Trouble shooting chart for DVP3160K/XX Abnormal color of video picture Abnormal color of video picture Yes Check whether the No Check Y1, R15, R217, C17 and C18 27MHz output signal is Yes Check whether the 3.3V and 1.8V power supply voltages on the decoder board are normal. No Check other of power supply electric circuit Yes Check whether the video filter network circuit is normal.
4-9 Trouble shooting chart Remark: Trouble shooting chart for DVP3160K/XX Remote reception is insensitive or fails. Remote reception is insensitive or fails. Go Check if the remote control works properly. No Check battery Yes Check if the power supply No Check voltage to the remote censor R315ǃC315 on the front board is normal are normal.
4-10 Trouble shooting chart Remark: Trouble shooting chart for DVP3160K/XX No video picture, no sound. No video picture, no sound. Go No Check whether all the voltages Check the loaded circuit from the power board to the decoder board are normal. CVBS(R85 point) waveform Yes Check if the reset circuit consisting No of CE10, and D3 is normal (at a Change CE10, and D3. high level for tens of milliseconds, then constantly at 0V).
4-11 Trouble shooting chart Spindle motor does not move Remark: Trouble shooting chart for DVP3156/XX, DVP3166(K)/XX Motor no move Go Check the FFC connection No Correct connection between 24P and the loader. Yes Check whether No “AVCC” Check (+5V) voltage is normal. the AVCC power supply Yes Check whether laser voltage No (2V for VCD & 2.2V for DVD) Check/Replace Q6ǃQ5. on Collector of Q6 and Q5 Yes 1. Whether voltage on pin 112 of U2 varies between 0 and 3.3V (3.
4-12 Trouble shooting chart The power can not be on or off Remark: Trouble shooting chart for DVP3156/XX, DVP3166(K)/XX The power can’t be on or off Go Check the power supply No Repair the power board on the power board is normal. Yes Check if the CON301 on the front board to CN5 Yes No Check/Correct connection on the decoder board is in good contact. Yes Whether the connection No to K301 is broken. Correct the connection Yes Whether there is 0V and 3.
4-13 All output voltages on the power board is 0V or deviated. Trouble shooting chart Remark: Trouble shooting chart for DVP3156/XX, DVP3166(K)/XX All output voltages on the power board is 0V or deviated Yes Check whether Yes Replace F1 F1 is blown No Check whether No Replace C4 if D1, D2, D3, D4 are normal. there is 300V on C4. Yes Check whether 100KHz oscillating signal on Pin6 of U1 No Check/ replace U1.
4-14 Disc cannot be read. Trouble shooting chart Remark: Trouble shooting chart for DVP3156/XX, DVP3166(K)/XX Disc cannot be read. Yes Check the FFC connection No Check the loaded circuit between 24P and the loader. Yes 1.Check voltage on pin 112 of U2 varies between 0 and 3.3V: Check whether there is laser voltage No (2V for VCD and 2.2V for DVD) on Æ3.3V for VCD Æ0V for DVD Collector of Q6 &Q5 2.
4-15 Only DVD disc or only disc except DVD can be played Trouble shooting chart Remark: Trouble shooting chart for DVP3156/XX, DVP3166(K)/XX Only DVD disc, or only disc except DVD can be Played. Go Check the FFC connection between 24pin and the loader. No Check the loaded circuit Yes Check laser voltage (2V) output No on Collector of Q6, if pin 23 of Check the solder status on U2 and peripheral components U2 is at low level. Yes No Check whether there is voltage variance on pin 23 of U2.
4-16 No display on LEDD, and buttons do not work Trouble shooting chart Remark: Trouble shooting chart for DVP3156/XX, DVP3166(K)/XX No display on LED, and buttons do not work Yes Check whether there is correct contact between CON301 and CN5 No Correct connection Yes Check VCC(+5v) voltage on the power and front board No Fix power supply board top a power supply for should electric circuit Yes Check there are CS, DATA and CLK signals on CON301 on the front board.
4-17 Trouble shooting chart Distorted audio and loud noise Remark: Trouble shooting chart for DVP3156/XX, DVP3166(K)/XX Distorted audio and loud noise Yes Check the power supply voltages +12V and -12V to the operation amplifying Q15 IS normal.
4-18 Trouble shooting chart Abnormal color of video picture Remark: Trouble shooting chart for DVP3156/XX, DVP3166(K)/XX Abnormal color of video picture Yes Check whether the 27MHz No Check Y1, R15, R217, C17 and C18 output signal is normal. Yes Check whether the 3.3V and 1.8V power supply voltages on the decoder board are normal. No Check other of power supply electric circuit Yes Check whether the video filter network circuit is normal.
4-19 Trouble shooting chart Remote reception is insensitive or fails. Remark: Trouble shooting chart for DVP3156/XX, DVP3166(K)/XX Remote reception is insensitive or fails. Go Check if the remote control works properly. No Check battery Yes Check if the power supply voltage to the remote censor is normal are normal.
4-20 Trouble shooting chart No video picture, no sound. Remark: Trouble shooting chart for DVP3156/XX, DVP3166(K)/XX No video picture, no sound. Go No Check whether all the voltages from the power board to the Check the loaded circuit CVBS(R85 point) waveform decoder board are normal. Yes Check if the reset circuit consisting No of CE10, and D3 is normal (at a Change CE10, and D3. high level for tens of milliseconds, then constantly at 0V).
5-1 5-1 A B C D E DVP3160K/XX WIRING DIAGRAM R Pr COAX Y 4 4 MAIN BOARD L CVBS Pb CN7 CN6 TDM-1+ KHM313 POWER SUPPLY CN2 24PIN*0.5 1 1 64M SDRAM 16M FLASH CN3 5PIN*2.0 7PIN*2.5 7 EEPROM CN9 5PIN*2.0 CN11 3PIN*2.0 CN5 9PIN*2.
5-2 5-2 A B C D E DVP3156/XX, DVP3166(k)/XX WIRING DIAGRAM SR SW Pr COAX R Y 4 4 CN L SL TDM-1 + KHM313 CN2 24PIN*0.5 1 1 5 64M SDRAM AM5888S 3 CN202 7PIN*2.5 7 KARAOKE A/D CS5340 16M FLASH CN5 9PIN*2.0 EEPROM 1 9 1 GND +5V IR DV33 GND DATA CS CLK POWER_K 2 CN9 5PIN*2.0 CN11 3PIN*2.0 3 1 5 MIC AGND -12V +5V GND CN3 5PIN*2.0 +5V +5V GND GND +12V AGND -12V 7 BM BP GND LOAD+ LOADTROUT GND TRIN 6 1 MOTER DRIVER SPSP+ LIMIT GND SLSL+ 6PIN*2.
6-1 6-1 1 2 3 4 5 Front Board Electric Diagram for DVP3160K/XX, DVP3166(K)/XX A A DV33 REM301 VCC GND IR FROM MAIN BOARD B 100 ohm IR 1 2 + GND POWER_K REM C306 0.1u C315 47p CON301 1 2 3 4 5 6 7 8 9 R315 3 2 1 GND 5V IR DV33 GND DATA CS CLK POWER_K CE301 47uF CON302 CON2(2.0) C316 47p 5V R303 R304 R305 5VL CON9(2.
6-2 6-2 1 2 3 4 5 USB + OK Board Electric Diagram for DVP3160K/XX, DVP3166(K)/XX A A R210 -12VA -12V 150 L200 VCC CE201 C201 22uF 0.1u C200 C201 R200 R208 R202 D200 C207 C208 C209 R201 R206 R204 R207 R203 RP200 CE201 CE200 C206 C205 R205 C204 R210 R209 C203 Q200 L200 U200A U200B G1 CN601 USB MIC200 +5V FB500R CE200 22uF C200 C205 47p 0.
6-3 6-3 Front Board Print-Layout (Bottom Side) for DVP3160K/XX, DVP3166(K)/XX Switch Board Print-Layout (Bottom Side) for DVP3160K/XX, DVP3166(K)/XX USB+OK Board Print-Layout (Bottom Side) for DVP3160K/XX, DVP3166(K)/XX
6-4 6-4 A B C D E Front Board Electric Diagram for DVP3156/XX 1 1 DV33 REM301 VCC GND IR FROM MAIN BOARD GND POWER_K 1 2 100 ohm IR + REM C306 0.1u C315 47p CON301 1 2 3 4 5 6 7 8 9 R315 3 2 1 GND 5V IR DV33 GND DATA CS CLK POWER_K CE301 47uF CON302 CON2(2.0) C316 47p 5V R303 R304 R305 5VL CON9(2.
6-5 Front Board Print-Layout (Bottom Side) for DVP3156/XX Switch Board Print-Layout (Bottom Side) for DVP3156/XX 6-5
6-6 6-6 1 2 3 4 5 Power Board Electric Diagram for DVP3156/XX, DVP3160K/XX, DVP3166(K)/XX F1 T2AL/250ac TR1 NTC 10 D1 1N4007 D2 1N4007 2 L1 680uH A + + A C12 102/400Vac 10K471 + C1 D3 1N4007 1 CON1 AC INPUT RV1 D4 1N4007 + C2 22uF/400V 22uF/400V D5 IN4148 C3 10uF/50V + L6 ⺕⦴ T1 EEL22 D6 IN4148 1 R2 R3 1/4W120K 1/4W120K + C5 152/1KV C4 47uF/25V C1 C10 C11 C12 C14 C2 C3 C4 C5 C6 C7 C8 C9 CON1 CON2 D1 D10 D2 D3 D4 D5 D6 D7 D8 F1 L1 L2 L6 R1 R10 R11 R12 R13 R2 R3 R4 R5 R7 R8
6-7 Power Board Print-Layout (Bottom Side) for DVP3156/XX, DVP3160K/XX, DVP3166(K)/XX 6-7
6-8 6-8 1 2 3 4 5 Main Board Electric Diagram for DVP3160K/XX: POWER& CONNECTOR TO FRONT PANEL MO_VCC MT1389HD (LQFP256) DVD MP Board for SONY KHM313AAA Q11 AO3401 S A Imax=1000mA CN1 1 1 2 3 4 5 6 7 7 8550C 50mA 20mA 100P A VCC VCC L2 R239 2 IR 100P R241 3.3K 1 2 2 VSDA 2 VSTB 2 VSCK PCON/LED 0R D2 1N4148 470R R17 1K L47 10 9 8 7 6 5 4 3 2 1 CN5 1K +12V 2 0R R23 POWER_K R33 R32 FB500R 10R DV33 C105 2.
6-9 6-9 1 2 3 4 5 Main Board Electric Diagram for DVP3160K/XX: MT1389HD&FRONTEND ADACVDD 0.1uF 0.47uF/NC R380 4.7R L7 CE31 1000uF/10v C11 XI XO C10 CE51 R217 R15 CE17 47uF/6.3v CE18 47uF/6.3v 0.1uF L12 C B A D RFO RN1 TDO TCK TMS TDI C32 1uF C33 1uF C35 1uF C34 C37 8 CLOSE STBY 7 TRIN 6 TROUT 5 1 2 3 4 1uF C36 120pF/NC 1uF C B A D 0Rx4 IO_19 IOA E F MDI1 C 1 E3 B R28 R27 LDO2 LDO1 RFV33 AVCC 2N3904 10k 100k CB14 T56 Q2 R29 10k 0.
6-10 6-10 1 2 3 4 5 Main Board Electric Diagram for DVP3160K/XX: SDRAM & FLASH DV33 SD33 L19 DV33 DV33A R9 A FB500R SD33 0R A 16Mb U7 B MA0 MA1 MA2 MA3 MA4 MA5 MA6 MA7 MA8 MA9 MA10 MA11 DBA0 DBA1 23 24 25 26 29 30 31 32 33 34 22 35 20 21 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 BA0/A13 BA1/A12 SDCLK SDCKE 38 37 CLK CKE DQ7 DQ6 DQ5 DQ4 DQ3 DQ2 DQ1 DQ0 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 19 18 17 16 DQM0 DQM1 15 39 DQML DQMH 36 40 NC NC CS RAS CAS WE VSS VSS VSS VCC VCC VCC
6-11 6-11 1 2 3 4 5 Main Board Electric Diagram for DVP3160K/XX: VIDEO OUT CN6 VIDEO OUT 1 2 . T96 CVBS 1 CVBS_OUTPUT A T97 Y_OUT . 1 4 T98 U_OUT NC(0) L24 R90 NC(2.4K) 5 . 1 R96 NC(33) 6 C24 CE5 YUV3 Q10 NC(3904) 1.8uH R72 75 1%(82R) R91 NC C62 100pF 100pF R89 100pF C22 C20 100pF 470u CVBS R92 C61 T99 V_OUT 1 R93 A . VCC_VIDEO 3 C19 100pF 100pF R94 0 R97 R95 NC(75) NC(1.3K) NC NC(82R) SCART SWITCH +12V R371 R372 SCART8 1.5K 1.
6-12 6-12 1 2 3 4 5 Main Board Electric Diagram for DVP3160K/XX: AUDIO OUT & SCART + C65 1 R299 FL- 4.7K 1% [NC] R300 0R SCART-L R77 470R1% [5.1K] 2 3300pF [1000pF] 2 U10A 0.1uF 10uF/16v CE53 1 4.7K 1% [NC] R303 470R1% [0R] U20 MUTE1 MUTE2 FL+ FLFR+ FR- CB53 CE27 0.1uF 47uF/16V C140 680pF [NC] 6 A LCH R307470R MUTE_L [NC] NJM4558 OPA R305 5.
6-13 Main Board Print-Layout (Top Side) for DVP3160K/XX 6-13
6-14 Main Board Print-Layout (Bottom Side) for DVP3160K/XX 6-14
6-15 6-15 1 2 3 4 5 Main Board Electric Diagram for DVP3156/XX, DVP3166(K)/XX: POWER&CONNECTOR & TO FRONT PANEL Q11 AO3401 S MO_VCC TO POWER BOARD Imax=1000mA CN1 1 1 2 3 4 5 6 7 A R4 10k Q14 50mA L41 FB AXIAL S8550 +P5V GND GND +P12V GND -P12V DV33 D G MT1389HD (LQFP256) DVD MP Board for SONY KHM313AAA 50mA VCC A C3 1u C108 0.1u VCC R2 2.2k 20mA 2 IR 100P 2.5mm*7 R241 3.
6-16 6-16 1 2 3 4 5 Main Board Electric Diagram for DVP3156/XX, DVP3166(K)/XX: MT1389HD&FRONTEND DV33HD 0.1uF CE17 47uF/6.3v CE18 47uF/6.3v 0.1uF C B A D RFO C11 XI XO R217 R15 RN1 TDO TCK TMS TDI 1uF C33 1uF C35 1uF C32 C34 1uF C36 120pF/NC C37 1uF C B A D 8 CLOSE STBY 7 TRIN 6 TROUT 5 1 2 3 4 0Rx4 IO_19 IOA E F MDI1 C 1 B E 3 AVCC 2N3904 LDO2 LDO1 RFV33 10k 100k CB14 T56 Q2 R29 10k V2P8 V20 V1P4 0.
6-17 6-17 1 2 3 4 5 Main Board Electric Diagram for DVP3156/XX,DVP3166(K)/XX: SDRAM & FLASH A DV33 DV33 DV33A R9 FB500R SD33 33R 2 16Mb U7 B MA0 MA1 MA2 MA3 MA4 MA5 MA6 MA7 MA8 MA9 MA10 MA11 DBA0 DBA1 23 24 25 26 29 30 31 32 33 34 22 35 20 21 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 BA0/A13 BA1/A12 SDCLK SDCKE 38 37 CLK CKE DCS# DRAS# DCAS# DWE# 19 18 17 16 CS RAS CAS WE DQM0 DQM1 15 39 DQML DQMH 36 40 54 41 28 NC NC VSS VSS VSS DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11
6-18 6-18 1 2 3 4 5 Main Board Electric Diagram for DVP3156/XX, DVP3166(K)/XX: VIDEO OUT A A VCC L24 0R VIDEO OUT CN6 D11 1N4148 CE5 1 CVBS YUV3 R72 2 T96 NC(470u) D12 . C61 75 1% CVBS 3 1 1N4148 NC C19 100pF . T97 Y_OUT . 1 4 T98 U_OUT 1 5 YUV4 0R Y_OUT T99 V_OUT 6 B 1 B .
6-19 6-19 1 2 3 4 5 Main Board Electric Diagram for DVP3156/XX, DVP3166(K)/XX: AUDIO OUT CE4 L56 + CE47 47uF/16v ABCK ALRCK M1 FILT+ REF-GND VA AINR VQ AINL RST/ C68 1000pF R77 5.1K + R348 100K 2 U10A NJM4558 OPA 0.1uF C159 C160 1u 0.1u C161 C162 C163 0.1u 1u 0.1u CE3 C69 10uF/16V 2 2 2 2 2 2 4 R83 5.1K R360 100 6 7 5 89_AL 89_AR 89_SL 89_SR 89_SW 89_CN R84 100 RCH + CE46 R319 Q8 MUTE NJM4558 OPA 8 + +12VB 100uF/16v C137 0.
6-20 Main Board Print-Layout (Top Side) for DVP3156/XX, DVP3166(K)/XX 6-20
6-21 Main Board Print-Layout (Bottom Side) for DVP3156/XX, DVP3166(K)/XX 6-21
7-1 DVP3156/XX, DVP3166/XX Mechanical Exploded View Remark: It's a general Mechanical Exploded View for DVP3156/XX, DVP3166/XX, Detailed information please refer to Model set.
7-2 ENCASING & ACCESSORIES PARTS LIST 12NC No.
7-3 DVP3160K/XX,DVP3166K/XX Mechanical Exploded View Remark: It's a general Mechanical Exploded View for DVP3160K/XX, DVP3166K/XX , Detailed information please refer to Model set.
7-4 ENCASING & ACCESSORIES PARTS LIST No 12NC No. Ass'y1 996510001196 / Part Name Front panel Ass'y for DVP3160K/55/77/78 SCREW LIST Q'ty 1 Front panel Ass'y for DVP3166K/93 No 12NC No. Part Name Q'ty 7 / S/T SCREW B 2.
8-1 REVISION LIST Version 1.0 *Initial release Version 1.1 Include DVP3166X/ 94 models Remark: This Service manual only for Philips Service repairment, Please Don't transmitt or forward it to others.
