A-trend AD-L528 With the draw closed, and with no disc in it. Press 7,6 and select on the remote, and this will take you into the firmware settings, use the arrows on the remote to scroll down to the region setting and change to whatever region you require then press enter. Then scroll to the bottom where it says 'next page' and press enter then on the next page scroll to the macro vision settings and press enter twice or until '0' is shown and the macro vision is disabled. Then press set-up to exit.
Press Down key twice Ver 4001 = macrovision enable Ver 4000 = macrovision disable Press left (<) or right (>) key Acoustic Solutions DVD551 Switch machine on with no disc in it and Press "Set-up" on remote. Then push Press Next > Stop > Pause > Prev > Next. This will bring up Region ID, up arrow to "bypass" for all regions. Press "Select/play" for confirmation. Afreey ADV-2360 Turn on the ADV-2360 without a disc in and open the Player Tray. Press SETUP on the remote to go to the set-up menu.
Plug the power into the unit but keep it turned off ("OFF" should be on display). Press and hold "MENU" button on unit, while holding pressed that key, do the same with "TOP MENU" (now you have two buttons pressed) and finally do so with "OSD" (you have to follow the sequence keeping pressed all previous keys) Once you have "MENU" "TOP MENU" and "OSD" buttons, hold them for at least 3 seconds and "FACTORY" should appears on display.
Code 1; Turn on player, Insert any disc. Open the lid and take out the disc and close the lid. Immediately press [Stop], wait few seconds. Press 8,7,X,0 (where x is the region code, e.g. –1) and then >> on remote. The player should be region free now! Code 2; Turn on player, Insert any disc. Open the lid, take out disc and close the lid. Immediately press [Stop] and wait few seconds. Press 8,7,2,0 and then >> on remote.
Code 1; Power on the player. Press, "pause" on remote. Enter code "314159". Player display reads "COdE - -" Enter 0 and Press "pause" again, Power off player. Wait 10 seconds and then power on again. Code 2; Press display without a DVD in the machine, select display and set video standard to (pal) not content specific. Alba DVD108 Press the 'pal/ntsc', press menu and press 0 Amoisonic DVD8506 Code 1; Power on the player, make sure the tray is open, and on the remote press: "0108x" Without the quotes.
Download the zipped MACRO/REGION FREE Firmware file. Make sure you get the one for the 1100w-1MB player. 1. If the archive does not contain a file named U1100AM.ROM then you have the wrong one. 2. Create a CD-R using the above file named U1100AM.ROM. Use the following specifications: a. ISO9660 b. Mode 1 c. Track at once d. Close the CD 3. Power on the player without a disk in the drive. 4. Insert the upgrade disk you just created Picture 5.
11. 12. 13. 14. The drive will eject the disk (screen will go blank)Picture (Remove the disk) The player will power off (screen is still blank)Picture Using the front panel power button (NOT THE REMOTE!), power the unit off After a short delay (3-4 seconds) power the front panel power switch back on Picture 15. Upgrade Complete! Apex AD-1200 Open tray and press 8 4 2 1 (you will see -'s appear top left of screen) Menu appears for region and Macrovision, Use up/down keys to select Region/Macrovision.
Press the Open/Close button on your remote control to open the tray. Press the buttons 1, 1, 1 and then 1 on your remote control, in order, one at time. Press the button 01 on your remote control to select Region 1, or 02 to select Region 2, and so on, or enter 13 to select Region Free. The word Region and then the number you selected should briefly appear on screen to confirm that the hack has been successful Ariston DVD 2000 On the players front press open. On remote press 7, 7, enter.
Is the same hack as Mustek DVD V300 because the players are the same. Bluesky DS-8315 Open the drawer of the reader via the remote control. Press successively keys 8, 4, 2, and 1. Choose the zone desired in the menu. If you wished to decontaminate Macrovision, press successively keys 4, 5, 6, and 1 Bush 1000 Open the player's tray, put in a Region One disc but do not close tray, Press the 0,1,2 and 3 buttons on the remote control followed by the play button. Bush 2000 Open the tray. Insert region 1 disc.
VER 2 = region 2. Also, you can select Version 255, which is region auto select. Then you press set-up twice, and insert the disc. It should work like that. Clatronic DVD-491 Power ON DVD, Open disk tray on front panel on DVD, Press Set-up button on IR remote. Press on IR remote 3 3 0 8. Press region code number (0 - code free) and Press Set-up button on IR remote.
CyberHome AD-M 212 When entering the Set-up menu via de [SELECT] - [7] - [6] - [ENTER], enter 13 for the region code and make it not only region code free, but have it altered permanently. Cyberhome AD-M 512 Same as above Cyberhome CH-DVD 302 Switch the player on and Open the Tray. Press "Stop". Enter "1999" with the remote control. Select "Region-Code" using the remote control. Press the "Enter" button on your remote control. Change the setting to "All". Confirm this with the "Enter" button.
Turn DVD on. Open the tray; do not put a disc inside. Press SETUP on the remote control. From the menu, choose PARENTAL CONTROL with the arrows on the remote. Once is highlighted press OK on the remote. On the PARENTAL CONTROL menu, choose DEFAULTS, and then highlight RESET (do not press OK at this point).
Daewoo DVG-5000N See http://www.nerd-out.com/darrenk/ for instructions Daewoo DVG-6000D Code 1 Put a region 1, 2, 3, or 4 and so on into the player when it comes up with "wrong region" just push the "title PBC" button on the remote and away you go. Codes 2 Same code as DVG3000N works Daewoo DVG-9000N See http://www.nerd-out.com/darrenk/ for instructions Daewoo S2122 Power up the unit, press OPEN, Press SETUP, insert 33088 followed by the zone number (0 = all zones).
Dantax DVD1500 Open the cd tray, Type 9999x, where x is the region. Close the cd tray. Dantax DVD450 Eject disc, Press 7 7 select on remote. This will bring up a secret menu. You can choose the region (13 all region). You can disable macrovision. Denver DVD-122 Open the DVD door by pressing the 'open' button on the remote. Press 33080 with the number pad on the remote. Press PLAY on the remote, and the DVD door will close.
Look at the Hack of Mustek V560 Eclipse DVD-595 Type 770 enter on the remote when in standby with no disc in machine. This gives you access to a menu to disable macrovision as well as making the machine Multiregion. Eclipse DVD-695 Switch power on then open tray and press 7,4 enter. A set-up screen will come up on screen, go to the bottom one then press enter. Macrovision should then appear, press enter till a zero appears, then press set-up to exit.
Encore DV450 Multiregion: press set-up and type 38883 on remote. Macrovision Hack: Enter SETUP (via remote) then enter 590419 to enter "loop hole" menu. Cursor to macrovision & set to OFF. Enzer E-5008B Set player to standby mode with the tray open. Press 0,1,2,3. Press Play. Enzer E-5015 Turn on the machine. Press Setup. Press Slow. Press Previous Track. Press Next Track. A service menu will now appear enabling you to change the region. Euroline 6620 Open the DVD tray.
GE Digital 5803P, GE Digital GE1101 http://www.nerd-out.com/darrenk/ GE Digital GE1105P, GE Digital GE1106P 1. Power on your player 2. Press stop and then press play on the player 3. Immediately you should see a language screen (if bought in usa you will have 3 options) select language 4. Then press the repeat button on your remote control 5. Using your remote control, enter the code below.
Goodmans GDVD 100 With no DVD/cd in the tray press set-up->menu->step->prev->next gives access to a secret menu. Region bypass can be accessed. Goodmans GDVD 124 Region Code Hack: Turn the power on / press 7,4 then select (if this doesn’t work, try 77). Secret menu is now enabled. Scroll down with the directional button to set the country code to = 13 or 0 then press [select] Press set-up to exit & save Macrovision On-Off: Turn the power on / press 7,4 then select. Secret menu is now enabled).
Open the drive tray, Press the buttons 8, 9, 2 and 6 on your remote control, and Press the button 9 on your remote control for Region Free, 1 for Region 1, 2 for Region 2 … Code 2 Eject the tray, Key in on the Remote Control 2180, Enter the Region code 1-6 If you want all regions, press 9 To disable Macrovision: Open the players tray, Key in from the Remote Control 4, 5, 6, 1 Turn Macrovision off by keying in 1, to turn it on again key in 0 GPX DV3000 Same as the 2000 model Gradiente D-10 Code 1 ON DVD wi
Grundig GDV 110 Grundig GDV 130 Open your DVD-drive, and press this on your Remote: SETUP - 9 - 2 - 0 - 0 - 0 STEP - SCHUFFLE – NEXT Macrovision off: SETUP-STOP-TITLE-PREV-SETUP Set this, while disk is running, stays like that until player is set into standby mode. Grundig GDV 200 Open the tray. Insert region 1 disc. Do not close the tray. Press 0,1,2,3 on the remote. Press Play. Grundig GDV 210 Same as above Grundig GDV 212 Same as above Grundig GDV 620HT Turn the machine on and open up the DVD tray.
remote. 3. Press Play on the remote. Your player is now a region 2 only player. To reset the machine to factory defaults, do the following: 1. Press Play on the remote, followed by 1, 5 and 9. 2. When the display reads '___ ____' enter 004 001 000 140 using the remote. 3. Press Play on the remote. Grundig Xenaro GDP 5100 This one was written for people who might not quite understand what to do {I was confused by the 5532 stuff and thought it was another code) 1. Select "i" on the remote 2.
scroll down the list. 16. Select the word "none" to make your unit region free. 17. The warning you see is probably meant to do nothing more than frighten you, I don't think you can damage your player by altering this since it's only altering region codes , which have nothing to do with anything vital to the unit. [no worse than changing TV channels really]. 18. press "i" to end. I'm in Australia and bought my player locally, so it appears that this probably works on all xenaro players.
Haier HD700 See http://www.nerd-out.com/darrenk/ for instructions Harman Kardon DVD1 Region code hack: With no DVD inserted put the player into STANDBY and on the remote press 3141592 and then number for region. Harman Kardon DVD10 Player off, without DVD. Wait till "NO DISC". With the remote put in ....3141592. now the Region code (1-4). now you must see on the display "Power on.
or 3.Press number button sequence "7","9","2","8" and "0" to turn ON Macrovision protection enabled (not video friendly) Himage 2290 To make this player multi-region, turn on the player and open the DVD draw. Type 8 8 0 0 using the remote control and then select the relevant region, e.g. 1, 2, 3 etc and 9 for region free. By setting the player to 9 it will play all DVD’s including the recently added Region Coding Enhanced DVD’s.
38767 o "02" should appear in the top left corner, this is the current region code. Press 9 on your remote and you are now region free. Hitachi DVP415U Open The DVD Drive, While Open, Press and hold Enter. Enter 1 for region 1 and so on insert your region (1-6) DVD. Hitachi DVP505E http://home.swipnet.se/moosenose2/dv-p505.html Hitachi DVP515 Same as Hitachi DVP305U Hiteker BI-600 Turn unit on (on the remote) do the following. Press set-up. Press stop. Press skip left. Press skip right.
To change the region code of this player just open the DVD tray and press 1 four times on the remote control followed by selecting desired region code 1 2 3 4... or 0 for all regions Hyundai HDV-2000 Open the tray. Enter 8-4-2-1. Select zone by Pressing "Enter" Hyundai HU-2010 Open the discs tray. Click on SETUP in your remote control. Got the sub-menu "Custom Setup" by pressing the right arrow on your remote 3 times. Click four times on the number 3 on your remote control.
When the display reads 000 5858 use the up and down buttons to change the 000 to 02E. Using the Left and Right arrow buttons, change the last four digits until they read 0000 for Region Free, 0101 for Region 1, 0202 for Region 2 or 0404 for Region 4. Press Enter on the player. Press Standby and wait 5 seconds. Press Standby again. Your player is now set to the region you requested. If you find some titles do not play on the region 0 setting, you may have to hard select the appropriate region.
Kenwood DVF-3530 Select the "set-up" menu by pressing the Menu button. Select "Audio" by pressing >. Select "Other" using the arrows and press "Enter". Select "7070" (Region Auto) using the number buttons. (7071 = Region 1). Press enter to save the new region. Turn off the DVD player. Wait for a few seconds and turn the player on. Kenwood DVF-5010 Before loading a disc, press and hold the play button on the unit itself (NOT remote control) for about five seconds.
Already region free, but here’s how to do the hack for RCE protected DVD movies! First load movie until you reach the Protected Notice World MAP. Then hit Stop twice, then hit PBC, wait 3 seconds and the PBC will be off, Next hit Play once again and it now plays! Konka KD-1800U Open Tray, press 6,6,6,6 then Select on the remote. Scroll down to Country code and set it to "13". Press Select then return to exit. Lasonic 3200 Open tray, press 4 times 1, press 1 time 9 and Close tray.
down right Lenco DVD-02 Put on the DVD open the tray. Type in the code 330880 after every number you have to wait until the hand disappears. Now your player is region and macrovision free. Or Lenco 202 enter set-up and press 167 on remote. This brings up the region menu, enter the digit from 1 to 6 of the region required. Lenoxx DVD2003 DVD on with No disc, Press SETUP NEXT PREV NEXT PREV with remote. You'll see "VER 1" on the upper left corner. With LEFT and RIGHT you can change the value.
No cd/DVD in player, press the menu key then, press key no 1, press key no 6, press key no 7, press the key "mute". After you pressed these keys you will get the message "CODE 1-6 all". The player is free for all codes now. Limit DVD8072 Open tray key in 8421. Select 9 for region free and Macro disable Limit DVD8080a Same as above Limit JDV300a To get it multiregion, press eject, put the disc in the tray, type in 8926 followed buy the region of the DVD you want to play and press play.
Maplin SMC-MK1 Open the tray, Press 7, Press Enter, Press 7, a service menu will now appear enabling you to change the region using the country code 13. Marantz DV-3100 Turn on without disk and wait for "No Disk" on front panel display. On front panel, press and keep pressed Pause, while you enter 3,1,4,1,5,9 on remote. Release Pause immediately after the "9". The word COdE is displayed on panel. Press number of region, or 0 for all regions.
Mediencom DS-8302 Open tray, Type 8 4 2 1 on your remote control -> OSD changes, to region code, Select desired region code (9=all regions) with 'enter', Close tray. Memorex MVD-2027 "SETUP", Press "1" for region 1 or press "2" for region 2 Press "7" for all regions, "PAUSE/STEP", " >>I ", " I<< ", "SETUP". Or Setup-key, 0-key (means zero / null), pause-key, I<< (means left), >>I (means right), set-up. MiCO A-980 Access the "secret" menu/set-up:- on the remote press 7, and then 7 again, then enter.
press SETUP, IN the Front Panel :, press NEXT, press STOP, press PAUSE/STEP , press PREV, press NEXT. Mustek DVD-V560 Make sure no disc is in tray, push – SETUP, NEXT, STOP, PAUSE/STEP, PREV, NEXT. Press RIGHT ARROW until you see "ver 255" (255 = Multiregion) Disable macrovision, press "SETUP", "NEXT", "PREV", "NEXT", "PREV" .
Press power+dimmer+previous (|<) all together the display’s shows _ _ _ _ . Press in sequence 1 9 9 9, the display shows A-0000 D-01 and Enter region code. Power off. NEC NDV-21 Make sure there is no Disc in the unit when you turn it on. Press pause on the remote. Press 3,1,4,1,5 and then 9 on the remote. Press the number for the required region(0 = all), Press pause. Turn the unit off then back on. Neufunk DT-2000 Press: stop stop setup slow |<< pause stop play play.
Switch on machine press open/close button, stop button, and forward search button all at the same time for 3-4 seconds and a hidden menu will appear, select the region. Orion DVD 337S Same as the 2000 model Oritron DVD100 With no cd in, press MENU, 1, 6, 7 and MUTE (unlock all regions) Or With no cd in, menu, 9, open, 5, mute. Oritron DVD200 Same as above Oritron DVD600 Same as above Oritron DVD650 Same as above Pacific PDVD-1000 Open tray, enter 8421, press enter until you get to no.9, close tray.
Remove the disc and close the disc tray. Press STOP STOP SETUP 3 8 8 8 3 and choose the region. Philco DV-P2100 Open tray, Press 8926 ("*" will be seen on the screen). Then select area (1 to 6) or "0" for all. Press PLAY (tray will close). Philco DV-P2500 Open the player's tray, Press 8 8 8 8 (four "*" will be shown on the screen). Select the region (1 to 6) or "0" for region free. Press play to end the operation and the tray will close.
on the remote (0=AUTO, 1,2,...=set region). Press, "PAUSE" on the remote. Power the player off, and then back on Philips DVD 707 Power on the unit. Press SETUP on the remote. Open the tray. Press code 8421 (the current zone will be displayed on screen). Press SELECT on the remote until zone 9 be displayed on screen. Close the tray. Philips DVD 710 Try the above or http://www.dvd.reviewer.co.uk/info/multiregion/full/philips750.
Philips DVD950 Turn the machine ON and remove any discs. When the display shows 'NO DISC'. Enter 'Play', '159'. The display will change to show 11 dashes ('-----------'). For region 1 enter the 12 digit code '005000128156', for region 2 enter the 12 digit code '002000128156'. Press 'Play' and the screen will turn red and then reset. Philips MX1060D Open Drive, Press System. Press 1 6 7 (in sequence) and you should now asked to select a region.
Turn on the DVD player, eject the drive and enter the following code: 8926. Then press the number that corresponds to the region you want to play or press 0 for auto region. You will know if done correctly as in the top left corner of the screen you will see the region number appear. Primare V10 Open disc tray. Press 9,8 and hit SELECT (you get the Service Menu), in the "region code" insert 14. In the "macrovision" (page 2 of the menu) insert 0. Press SELECT and RETURN.
Without any disc in player press, Setup, Mute, Last, Next on the RC. Choose region RCA DRC220N Press menu, 1,6,7 then mute to play all regions REC 850 Switch on the player and Open the tray. Push 'stop' and enter numerals 1 9 9 9. Select region 'ALL', exit from screen by pressing 'set-up' button. Redstar DVD 229A Open the tray. Type stop and 1999 and change region code in menu (with enter/arrows) then close tray. Redstar DVD 229C Open tray and type 3308 and then the region code, (0=codefree).
Roadstar DVD-2027H Open the drive tray. Make sure there's no DVD in it then Type 9 8 1 7 or 8 4 2 1 on the remote keypad. You will then be into a hidden menu and Choose regions 1-6 or 9 for region free clicking SELECT (Enter) button. close the tray. Turn the player off for few seconds. Turn it on again. Rowa DVD-280 Press, open/close, zoom, a-b, up, left, down, right. Or Turn the player on without a disc in it or disc tray open.
(Auto/Off). Chose "Bypass". Press "Setup" again. The player is now region- and Macrovision-free. Sampo DVE-611 Create a txt filed called CREGIN.TXT, Put this is the txt file TSDVDREG-20019629735-R0. Burn to a cdr ISO9660, mode 1 file format and Insert cdr in player, Samsung DVD 511, Samsung DVD 611 Power on your player. Press and hold both the Play and Stop buttons on the player. After a short while you should be presented with a set of language options. Release the Play and Stop buttons on the player.
will now be superimposed over the Samsung logo on your TV screen - this number represents the current region setting of the player (e.g. for region 2 you will see 02). Now press the number of the region you would like your 709 to become: 1 = region 1, 2 = region 2.ect. 9 = region free setting (probably the best unless you've got an RCE region 1 disc).
Using the AIWA remote control. Press Repeat (DVD player's display will be totally light.)Press Program. Press Clock several times (usually 2) and the display will show the word "ADJUST". At this time using the DVD remote control press 9. DVD deck will close automatically and play the disc. Samsung DVD M103, Samsung DVD M105 Switch the player off and on. Hold the play and stop buttons (for 10 seconds). Press the Repeat button on your remote control.
turn it off, every time you turn it on, you must do all the steps again to be able to see other region movies. Samsung DVD S224 Turn DVD player on with no disc inserted. Press "REPEAT" once on your remote control.
OPEN, SETUP, x, 2, 0, 1, 0, STEP, SHUFFLE, NEXT. Where x is: 1 for Region 1, 2 for Region 2 … 9 for multi-region Macrovision hack; SETUP, STEP, TITLE, PREV Then turn off player. Scan SC-2500 Open Tray. Enter:0106 on the Remote Control then Enter:Region Number on the Remote Control. (1=Region 1,2=Region 2,0=Multi-region none RCE etc ). OK will now appear on screen. Schaub Lorenz SL-D4000 Power on. Push open/close on the remote control. Type 3308; the player displays 'XXXX' on the upper left corner.
When the player shows the map screen and say "cannot play on modified region 1 players". When this screen appears, you must press the "menu" button several times, and the movie starts. Sharp DV-740 Write: TSDVDREG-2001-8939912-R0 (but write R1 R2 etc. for whatever region) to a notepad file, save as CREGIN.
Skyworth 650 Open cd drawer, Key in (using remote) 8926# (# = region code number i.e. 1,4 etc. 0 = multi region and no macrovision) SM Supervision 1000, SM Supervision 1100 Empty DVD tray. Press set-up on remote, step, prev, next. Enter the menu. You can now see the version or change some settings like region id (set bypass for all regions), Css auto/off and MACROVISION.
Open the tray. Press 7,7, Select. A service menu will now appear. Scroll down to "Country Code" and press SELECT on the remote. Change the setting to the desired region or 13 for all. Press SELECT. Press RETURN to exit the menu.
Sony DVP-NS300, Sony DVP-NS305, Sony DVP-NS400D, Sony DVP-NS700, Sony DVP-S330, Sony DVP-S335, Sony DVPS360, Sony DVP-S336, Sony DVP-S525D, Sony DVP-S530D, Sony DVP-S535D, Sony DVP-S536D, Sony DVP-S725D, Sony DVP-S735D Turn on the unit with the remote controller, Wait until "no disc" appears in the unit's display. Press the keys: PAUSE, 3, 1, 4, 1, 5, 9. And "CODE" will appear in the display.
Sunny DVD-650 Open the tray. Enter 8926 then press region number that you want (9 for multi region). Insert your DVD in drive and close the tray. Talent DVD-650 Same as above Tatung TDV5100 Open the tray then, Press set-up, stop, rew skip, FF skip. Teac DV-2000, Teac DV-2000, Teac DV-3000 Open the tray, enter 2168 using remote control then enter region code e.g. 1 for USA or 4 for Australia, 0 for all.
Press the 9 button on your remote control for Region free, or 1 – 6. Press the Open button on your player. Press the Standby button on your remote control if the player sticks on FBI Warning screens. Press Forward Search x2 or faster, the disc should skip straight to the main feature Or Without disc in the player. On your rc Press: "Repeat", 3 8 7 6 7 : 9, "Open" on your player.
Hold Stop, Turn on, Press open/close and Skip(=>>) at the same time. Select region on the menu that appears United DVD 2151 Make sure you don’t have any DVD inserted and Door Closed. With the remote control: press SETUP, NEXT, STOP, PAUSE/STEP, press PREV, press NEXT. United DVD 2255, United DVD 3151 Open tray, enter 3308 (you'll see **** on the top left of the screen). Enter region code of your choice (0-6. 0 is all regions) (you'll see the number of the region selected on the top left of the screen).
Vtrek DVD-9901B Open the DVD-Drive, On the remote enter the Code "2168+Regioncode(1-6)" and Close the DVD-Drive. Wharfedale 750 Open draw, place disc on draw, on remote 0, 1, 2, and 3, close draw or play. Player is now region free. Wharfedale M5 Press SETUP, 6, 2, 8, 3, 6 on the remote control. You should now be in the Factory Menu, where you can select either ALL for region-free, or a specific region Wintel WIN9663 With the disc tray open. Press Setup, Step, Prev, Next.
Yukai DVD-V300 This is the same hack as Mustek DVD V300 because the players are the same. Yukai DVD-V560 Power up DVD without a disk. Press set-up on the remote. On the player press next,prev,next,prev. Region code should be displayed on top right corner of screen. Use the keys on the remote to: Use left/right arrow keys to change region code to 255. Press down arrow. 3001 should be displayed. Use left/right arrow to change to 3000. Press down arrow. 4001 should be displayed.
