DVD Player User Manual

ManualsBrandsPhilips ManualsDVD PlayerDVD963SA

Published by MW 0271 Service PaCE Printed in the Netherlands Subject to modification EN 3122 785 12331

retrieval system or transmitted, in any form or by any means, electronic,

mechanical, photocopying, or otherwise without the prior permission of Philips.

DVD-Video Player DVD963SA

DVD963SA /001 /171 /691

CL 26532105_000.eps

280802

Contents Page Contents Page

1 Technical Specs and Connection Facilities 2

2 Safety Instructions, Warnings, and Notes 3

3 Directions for Use 4

4 Mechanical-, Dismantling Instructions, and Service

Hints 18

5 Diagnostic Software, Trouble Shooting and Test

Instructions 21

6 Block-, Wiring Diagram and Testpoint Overview

Block Diagram 41

Wiring Diagram 42

Testpoint Overviews 43

7 Electrical Diagrams and Print-Layouts Diagram PWB

Power Supply Unit 46

AV Board: SYS Clk & Control (Diagram A1) 47 53-56

AV Board: Upsampling DAC (Diagram A2) 48 53-56

AV Board: Audio DAC (Diagram A3) 49 53-56

AV Board: Curr to Volt. Converter(Diagram A4) 50 53-56

AV Board: Audio (Diagram A5) 51 53-56

AV Board: Video & SCART (Diagram A6) 52 53-56

Front Board: Display (Diagram D) 57 58-61

P-Scan Board: Line Doubler (Diagram P1) 62 65-70

P-Scan Board: Encoder (Diagram P2) 63 65-70

P-Scan Board: Video Output (Diagram P3) 64 65-70

Standby Board (Diagram S) 71 71

Double Scart Panel: Switching (Diagram S1) 72 74-76

Double Scart Panel: SCART (Diagram S2) 73 74-76

8 Alignments (Not Applicable) 77

9 Circuit Descriptions 77

List of Abbreviations 86

IC Data 87

10 Spare Parts List 91

Summary of content (82 pages)

PAGE 1
DVD-Video Player DVD963SA DVD963SA /001 /171 /691 CL 26532105_000.
PAGE 2
EN 2 1. DVD963SA Technical Specifications and Connection Facilities 1. Technical Specifications and Connection Facilities Specifications PLAYBACK SYSTEM DVD Video SACD multi channel and SACD stereo Video CD & SVCD CD (CD-Recordable and CD-Rewritable) MP3 CD AUDIO PERFORMANCE (Without upsampling) DA Converter DVD CD/Video CD S-Video CD 24 bits fs 96 kHz fs 44.1 kHz fs 48 kHz fs 44.
PAGE 3
Safety Instructions, Warnings and Notes DVD963SA 2. EN 3 2. Safety Instructions, Warnings and Notes 2.1 Safety Instructions 2.2 Warnings 2.1.1 General Safety 2.2.1 General Safety regulations require that during a repair: • Connect the unit to the mains via an isolation transformer. • Replace safety components, indicated by the symbol , only by components identical to the original ones.
PAGE 4
When a disc is loaded, unlock the tray by pushing the slide inwards with a screwdriver and pull tray outwards. Front Standby board Î Remove cable connection. Î Remove 2 screws 105. (Board to Front cabinet) Î Dismount board. Manually opening of tray When it is not possible to open the tray with the EJECT button, the tray can be manually opened. When no disc is loaded, unlock the tray by moving the slide from left to right and pull tray outwards. Front Display board 1002 Î Remove cable connections.
PAGE 5
Mechanical-, Dismantling Instructions, and Service Hints 4. EN 19 Exploded View CL 26532105_003.eps 270802 4.
PAGE 6
EN 20 4. DVD963SA 4.3 Service Hints 4.3.1 Switched Mode Power Supply Mechanical-, Dismantling Instructions, and Service Hints 4.3.3 For assistance with the repair process of the monoboard an electronic fault finding guidance has been developed. This program is called ComPair. This ComPair program is available on CDROM. The version of the CDROM for repair of the monoboard is V1.3 or higher and can be ordered with codenumber 4822 727 21637.
PAGE 7
Diagnostic Software, Trouble Shooting and Test Instructions DVD963SA 5. EN 21 5. Diagnostic Software, Trouble Shooting and Test Instructions 5.1 Dealerscript 5.1.1 Purpose of Dealer Script 5.1.2 The dealer script can give a diagnosis on a standalone DVD player, no other equipment is needed to perform a number of hardware tests to check if the DVD player is faulty. The diagnosis is simply a "error" or "pass" message. No indication is given of faulty hardware modules.
PAGE 8
EN 22 5. DVD963SA 5.2 Player Script 5.2.1 Purpose of Player Script Diagnostic Software, Trouble Shooting and Test Instructions Press the OPEN/CLOSE key to proceed to the next test. 5.2.4 The Player script will give the opportunity to perform a test that will determine which of the DVD player's modules are faulty, to read the error log and error bits and to perform an endurance loop test.
PAGE 9
Diagnostic Software, Trouble Shooting and Test Instructions 5.3 Display PCB 5.3.1 Display Test KEY ID 0 1 2 3 4 5 6 7 E F The display test is performed by nucleus DispDisplay. By putting a serie of test patterns on the local display, the local display is tested. To step through all different patterns, the user must either press OPEN/CLOSE (pattern is ok) or STOP (pattern was incorrect) to proceed to the next pattern. The display of patterns is continued in a cyclic manner, shown in Fig.
PAGE 10
EN 24 5. DVD963SA Diagnostic Software, Trouble Shooting and Test Instructions pressed the PLAY key. Pressing the PLAY key, before pressing a key on the remote control, gives an error in the remote control test (note that the remote control test will also fail if a key on the remote control was pressed but no code was received). The remote control test does not check upon the contents of the received code, that is it will not be checked if the received code matches the key pressed.
PAGE 11
Diagnostic Software, Trouble Shooting and Test Instructions 5.4 Mono PCB Digital Part 5.4.1 Picture Test DVD963SA 5. EN 25 The test can be left by pressing the PLAY key for more than one second. 5.4.3 The picture test is performed by putting a predefined picture (colour bar) on the display (nucleus VideoColDencOn), and asking the user for confirmation. The display will show the following message: Sound 2 Test The second soundtest is performed by producing a sine sound (nucleus AudioSineOn).
PAGE 12
EN 26 5. 5.5 Basic Engine 5.5.1 Version Number DVD963SA Diagnostic Software, Trouble Shooting and Test Instructions In the basic engine tests, the version number of the Basic Engine will be shown first, as the following example: CL 16532162_043.eps 080102 Figure 5-25 By pressing OPEN/CLOSE the user confirms that the disc motor is running. Pressing STOP indicates the disc motor does not work. Pressing PLAY proceeds to the next test, after a reset of the disc motor (nucleus BeDiscMotorOff).
PAGE 13
Diagnostic Software, Trouble Shooting and Test Instructions DVD963SA 5. CL 16532162_046.eps 080102 CL 16532162_048.eps 080102 Figure 5-31 Figure 5-28 Only the identification number (decimal) representing set errorbits will be shown. By pressing OPEN/CLOSE or STOP, the user can move forward or backward (respectively) through the logged errorcodes. If the display only shows "EB-0", no error bits were set. By pressing PLAY the user can continue to the next test.
PAGE 14
EN 28 5. DVD963SA Diagnostic Software, Trouble Shooting and Test Instructions After one loop cycle: Display the 3-digit module bits together with the last error code which occured in the loop test. The 4 digits at the right side of the display (fig. 5-34) show the last error that was found during the loop test. The leftmost two digits (54) of this code indicates which nucleus resulted in a fault. The rightmost two digits (03) refer to the faultcode within that nucleus.
PAGE 15
Diagnostic Software, Trouble Shooting and Test Instructions Error Code 0008 5.6.2 DVD963SA 5. EN 29 SMA Error Codes Error name Explanation SP_CONTINU Sequence of sectors coming ITYERROR from disc is incorrect. Reason: see SP_SYNCERROR 0009 DMX_CONTI NUITYERRO R Sequence of sectors is incorrect. Reason: problem with buffer RAM 000A LLD_ERROR An illegal audio format was offered to the decoder.
PAGE 16
EN 30 5.6.3 5. DVD963SA Diagnostic Software, Trouble Shooting and Test Instructions Trade Mode When the player is in Trade Mode, the player cannot be controlled by means of the front key buttons, but only by means of the remote control. TO ACTIVATE TRADE MODE TO DEACTIVATE TRADE MODE POWER ON POWER ON DURING STOP MODE AND W/O DISC. PRESS REMOTE KEYS COMBINATION <259> DURING STOP MODE AND W/O DISC.
PAGE 17
Diagnostic Software, Trouble Shooting and Test Instructions Table 5-2 Processor and peripherals DVD963SA 5. EN 31 Ref. # Reference Name Remark 80d DAC_ModeDSD Sets DAC to DSD mode 81a DAC_LowPowerStandby Enable Low Power On Standby Ref.
PAGE 18
EN 32 5. DVD963SA Diagnostic Software, Trouble Shooting and Test Instructions Table 5-7 Log (Error logging in Nvram) Ref. # Reference Name Remark 31 LogReadErr Read last Errors 32 LogReadBits Read errors Bits 33 LogReset Reset Ref. # Reference Name Remark 84a Furore_High Sets Furore output pins DSD_PCM0-9 to high 84b Furore_Low Sets Furore output pins DSD_PCM0-9 to low Table 5-11 Karaoke (not available) Table 5-8 Miscellaneous Ref. # Reference Name Ref.
PAGE 19
Diagnostic Software, Trouble Shooting and Test Instructions 4 5 6 7 8 DVD963SA 5. EN 33 MAIN > AUDIO > SINE WAVE MENU 1 Audio Sine On [21a] 2 Audio Burst On [21b] Basic Engine... Processor Peripherals... Error Log... Furore... Miscellaneous... MAIN > AUDIO > DIGITAL PORTS MENU 1 No tets available First Level Submenus MAIN > AUDIO > EXT DAC BOARD MENU 1. DAC Reset [79] 2. I2C Test... 3. Clock... 4. Audio... 5. Low Power Standby... 6. DAC Mode... MAIN > AUDIO MENU 1 Mute... 2 Pink Noise...
PAGE 20
EN 34 4 5 5. DVD963SA NVRAM Modify NVRAM Read/Wr Test Diagnostic Software, Trouble Shooting and Test Instructions 3 [36] [15] MAIN > MISCELLANEOUS > STATISTICS INFO MENU 1 Total Nr Of Times Tray Open [47a] 2 Total Time Power On [47b] 3 Total Play-Time CDDA & VCD [47c] 4 Total Play-Time DVD [47d] 5.8 Jump To Outside Grooves [42c] Nuclei Error Codes In the following tables the error description of the error codes will be described. 5.8.
PAGE 21
Diagnostic Software, Trouble Shooting and Test Instructions 5.
PAGE 22
EN 36 DVD963SA Diagnostic Software, Trouble Shooting and Test Instructions Error code Error text Error code Error text 4104 “Basic Engine returned error number XX” 3041 “Disp not responding” 4120 Test successful 3042 “Disp key no response” 4121 “Parity error from Basic Engine to Serial” 3043 “One or more patterns not correct” 4122 “Unexpected response from Basic Engine” 4123 “Communication time-out error” 2700 “Model name in wich the test is running” 4124 “Basic Engine returned err
PAGE 23
Diagnostic Software, Trouble Shooting and Test Instructions 5.8.5 Error code Error text Error code Error text 1104 “NVRAM reply time-out” 1500 Test successful 1502 “NVRAM access time-out” 1504 “NVRAM fails” Test successful 1200 Test successful 1202 “Slave bus not working” 5.
PAGE 24
EN 38 Error code DVD963SA Diagnostic Software, Trouble Shooting and Test Instructions Error text 2301 Color Denc On transmit error 2302 I2C Color Denc On bus busy 2320 Video colourbar Off OK 2340 Video colourbar On NTSC OK 2400 ADV7300 com OK 2401 I2C ADV7300 com bus busy 2402 ADV7300 com transit error 2403 No ack from ADV7300 com 2404 ADV7300 com response error 2420 FLI2200 com OK 2421 I2C FLI2200 com bus busy 2422 FLI2200 com transmit error 2423 No ack from FLI2200 com 2424
PAGE 25
Diagnostic Software, Trouble Shooting and Test Instructions 5.9.3 Audio DAC And Amplifier Ensure that the Audio mute signal is OFF To check the DAC and buffer amplifier,send the following commands. Ref.# Command Name Remarks Audio output 21a AudioSineOn Audio Sine signal ON Sine,1Khz on stereo ---- Press stop button Audio Sine signal OFF No waveform 5.9.6 Command Name Remarks 25c VideoScartHi EN 39 Sends out 12V ± 10% Kill Circuit Ref.
PAGE 26
EN 40 5.
PAGE 27
Block and Wiring Diagram. DVD963SA 6. 41 6. Block and Wiring Diagram. Block Diagram DVD963SA P_HSYNC P_VSYNC DAC_F MT48LC2M32TG-8 RGB SLB FBOUT L/R P50 Y/CVBS I2C P50 7101 FLI2301 ADV7300 7303 V +5VM -5V +12VSTBY DOUBLE SCART BOARD KILL 7100 DAC_E 8V FLEX 22P CVBS 7202 +3V3D LF18ABT AUDIO L/R 7302 U 7103 YB(0-9) YA(0-9) UVA(0-9) AV Switch Matrix YC +1V8 7301 7501 12V 12V GENERAL BLOCK DIAGRAM FOR DVD963SA P50 7500 +2V5 RGB 7300 LF25C 7201 DAC_D 1001 P.
PAGE 28
Block and Wiring Diagram. DVD963SA 6.
PAGE 29
Block and Wiring Diagram. DVD963SA 6.
PAGE 30
Block and Wiring Diagram. DVD963SA 6.
PAGE 31
Block and Wiring Diagram. DVD963SA 6.
PAGE 32
Electrical Diagrams DVD963SA 7. 46 7. Electrical Diagrams Power Supply Unit DVD963SA 1 2 3 4 5 6 8 7 2190 Super Audio Cd Wide Range High End 9 10 11 12 13 FOR INFORMATION ONLY.
PAGE 33
Electrical Diagrams DVD963SA 7.
PAGE 34
Electrical Diagrams DVD963SA 7. 48 AV-Board: Upsampling 1 2 3 4 5 6 7 8 9 10 11 12 13 2V / div DC 2us / div 2V / div DC 100ns / div 2V / div DC 10us / div 2V / div DC 20ns / div +3V3D 7206-C 74LVC04 14 5 4 6 A6 A6 10 7 7 7 +3V3D +3V3D 7206-E 74LVC04 14 11 SPDIF_OUT +3V3D 7206-B 74LVC04 14 3 DIG_OUT A1 24.576M A1 A3 FR_MCLK A Upsampling A3 A3 I203 I202 FR_LRCK I201 A3 I200 FR_BCK A FR_DATA UPSAMPLING +5VD 100n 1~ MUX 3 4 I201 7 D +5VD A1 24.
PAGE 35
E lectrical Diagrams DV D963S A 7.
PAGE 36
Electrical Diagrams DVD963SA 7.
PAGE 37
Electrical Diagrams DVD963SA 7. 51 AV-Board: Audio 1 2 3 4 5 6 AV AUDIO 7 8 9 10 11 BAS316 4V3 6500 I541 I543 47K 3579 3580 100R BC857B I417 13 STEREO_R_OUT 220R I539 +5VSTBY I411 I510 3540 A4 STEREO_R A 12 7536 BC857B 7522 STEREO L/R +5VSTBY 3590 0V 3541 I571 0V7 3K3 7521 BC817-25 1K I542 1401-A YKC21-4105 2 RIGHT A I418 I424 +5VD B *4503 * 4K7 3581 1 BC847B 0V I570 0V7 I521 3551 -8V 1K AVCC_C 10R 10R 2.00 V / div DC 500us / div 2.
PAGE 38
Electrical Diagrams DVD963SA 7.
PAGE 39
Electrical Diagrams DVD963SA 7.
PAGE 40
Electrical Diagrams DVD963SA 7.
PAGE 41
Electrical Diagrams DVD963SA 7. 55 Layout AV-Board (Part 1 Bottom Side) CL 26532105_12a.
PAGE 42
Electrical Diagrams DVD963SA 7. 56 Layout AV-Board (Part 2 Bottom Side) CL 26532105_12b.
PAGE 43
Electrical Diagrams DVD963SA 7. 57 Display Panel 1 2 3 4 5 6 7 8 9 10 11 12 13 1111 15-MT-67GNK DISPLAY PANEL 2123 I180 I147 I140 I148 I130 I135 I131 I136 I132 I137 I133 I138 I134 I139 I120 I181 I153 I156 I150 I157 I151 I155 I152 I158 I141 I145 I142 I149 I143 I146 I144 I154 G(14) 220p 3107 I125 5V 0V I121 0V P50 interface to SCART 3108 220R B P50 INFO : FIL1 - FIL2 = 3.
PAGE 44
Electrical Diagrams DVD963SA 7. 58 Layout Display Panel (Top Side) 1100 D1 1101 C22 1102 A22 1103 C16 1104 A21 1105 C21 1106 A19 1108 A16 1111 B8 1112 B16 1113 B2 1114 C19 1119 B9 1120 D1 2103 B14 2107 A18 2127 B17 2136 B15 2138 A14 2139 C14 2143 A13 6104 B2 6105 C1 6106 B16 6107 B2 7106 A15 7109 A14 7402 B13 CL 26532105_015.
PAGE 45
Electrical Diagrams DVD963SA 7. 59 Layout Display Panel (Overview Bottom Side) 2102 2104 2105 2106 2108 B5 A16 A16 A17 C11 2109 2122 2123 2124 2129 B14 B12 B12 B17 A5 2131 2133 2134 2135 2137 B13 C12 C12 B8 C8 2140 2141 2142 2144 3100 C11 B10 C11 C14 B11 3101 3102 3103 3104 3105 A15 A15 B11 A15 C22 3106 3107 3108 3109 3110 B12 B12 B13 C2 C2 3111 3112 3113 3114 3115 C3 B16 C16 C16 B5 Part 1 CL 26532105_16a.
PAGE 46
Electrical Diagrams DVD963SA 7. 60 Layout Display Panel (Part 1 Bottom Side) Part 1 CL 26532105_16a.
PAGE 47
Electrical Diagrams DVD963SA 7. 61 Layout Display Panel (Part 2 Bottom Side) Part 2 CL 26532105_16b.
PAGE 48
Electrical Diagrams DVD963SA 7.
PAGE 49
E lectrical Diagrams DV D963S A 7.
PAGE 50
Electrical Diagrams DVD963SA 7.
PAGE 51
Electrical Diagrams DVD963SA 7.
PAGE 52
Electrical Diagrams Layout P-Scan Board (Part 1 Top Side) DVD963SA 7.
PAGE 53
Electrical Diagrams Layout P-Scan Board (Part 2 Top Side) DVD963SA 7.
PAGE 54
Electrical Diagrams DVD963SA 7.
PAGE 55
Electrical Diagrams Layout P-Scan Board (Part 1 Bottom Side) DVD963SA 7.
PAGE 56
Electrical Diagrams Layout P-Scan Board (Part 2 Bottom Side) DVD963SA 7.
PAGE 57
Electrical Diagrams DVD963SA 7. 71 Standby Board Layout Standby Board (Top Side) 1 2 100R A A TO 1131 OF DISPLAY BOARD LB3333 6200 I200 3200 STANDBY BOARD I201 I202 STANDBY 1200 +5Vstb 1 Stdby_Ctrl 2 I203 STBKEY+3 3 I204 STBKEY-4 CL 26532105_025.eps 270802 B 440053 2 6 Layout Standby Board (Bottom Side) 1 5 * 1202 4 B 1201 1200 1201 1202 6200 1200 A2 1201 B1 1202 B1 3200 A1 6200 A1 I200 A1 I201 A2 I202 B2 I203 B2 I204 B2 SPEC CL 26532105_024.
PAGE 58
Electrical Diagrams DVD963SA 7.
PAGE 59
Electrical Diagrams DVD963SA 7. 73 Double SCART Panel: Switching (Only for EU models) 7 3200 4u7 2202 220R 3202 3203 4u7 470R 3204 27K 2203 3205 4u7 220R S1-4 LIN_TV BC_TV 3272 1 S1-12 2204 4u7 470R MTB 500ns MTB10.
PAGE 60
Electrical Diagrams DVD963SA 7. 74 Layout Double SCART panel (Only for EU models) (Overview Top Side) Part 1 CL16532007_95a.eps Part 2 CL16532007_95b.eps CL 16532007_095.
PAGE 61
Electrical Diagrams DVD963SA 7.
PAGE 62
Electrical Diagrams DVD963SA 7. 76 Layout Double SCART panel (Only for EU models) (Part 2 Top Side) CL 16532007_95b.
PAGE 63
Alignments DVD963SA 8. EN 77 8. Alignments Not applicable. 9. Circuit Descriptions and List of Abbreviations Index of this chapter: 1. Introduction 2. Power Supply Unit (PSU). 3. Loader/Mono Board. 4. Audio Video (A/V) Board. 5. Front Display Board. 6. Abbreviations 7. IC Data Notes: • See also the SD4.00SA_CH Service Manual (3122 785 12480). • Figures can deviate slightly from the actual situation, due to different set executions.
PAGE 64
EN 78 9. DVD963SA Circuit Descriptions and List of Abbreviations 9.3 K Loader/Mono Board (for diagrams see SD4.00SA_CH Service Manual) R Loader 2.5V FRONT-END DVDalas2+ A CL 96532065_071.eps 130799 Loader-interface Iguana HF Buffer Figure 9-2 TL431 This reference component has two functions: • A very stable and accurate reference diode • A high gain amplifier.
PAGE 65
Circuit Descriptions and List of Abbreviations • • The Servo Processor/Decoder The Interface/Program Memory The SAA7812 is also a combined CD/DVD compatible decoding device. The device operates with built in hardware for CD/DVD error correction and de-interleaving operations. It decodes EFM or EFM+HF signals directly from the laser preamplifier, including analogue front-end, PLL data recovery, demodulation, and error correction.
PAGE 66
EN 80 9. Circuit Descriptions and List of Abbreviations DVD963SA Block diagram Input Input data comes from the I2S-bus. The front-end interface of this device, accepts DVD, CD and CD-DA information. For audio, the processing cell is a fully compatible DTS, Dolby Digital (AC-3), MPEG1, MPEG2, PCM decoder, capable of decoding 5.1 and 2 channel streams. 3 HF AGC IEC 958 4 Register Host interface Host interface 8 bits AD PCM_CLK DSD_CLK 2 IEC 958 gen.
PAGE 67
Circuit Descriptions and List of Abbreviations – – – Stereo PCM data output. Two possible stereo sources can be selected as stereo PCM output: 1. Stereo PCM coming from the STi55xx via the PCM input on Furore. 2. Stereo or down-mix-PCM derived via a decimation filter from the SACD-DSD signal. Digital audio output interface (IEC958). The IEC958 format is intended to connect the DVD736SA to a digital receiver. No DSD signals are defined for IEC958, therefore the 'DSD-->PCM converted' signal is transmitted.
PAGE 68
EN 82 9. Circuit Descriptions and List of Abbreviations DVD963SA Clock Factory One clock factory is implemented to support all clocks required by the Furore 2. The various master clock, which depends on whether SACD is present, is used for SD4.00_SA_CH. The clock factory of SD4.00_SA_CH is showed in Figure 8-2. Service 5V 1k S1 27MHz P-SCAN FURORE 2 16.9344 MHz FURORE 2 (Optional) Clock Buffer 16.
PAGE 69
Circuit Descriptions and List of Abbreviations The SACD DSD/DST decoder Furore 2 uses 1.8V for its core and analogue portion, and 3.3V for its interface. The on-board 1.8V linear regulator LF18ABDT and 3.3V linear LD1117DT33 are used to generate 1.8V and 3.3V power supply respectively. The back-end section mainly uses the 1.8V or 2.5V and 3.3V, which depend on which back-end processor is used. The onboard linear regulators LF25ABDT or LF18ABDT are used to generate the 2.5V (or 1.8V) required by the STi55xx.
PAGE 70
EN 84 9.5 9. Circuit Descriptions and List of Abbreviations DVD963SA Progressive Scan Board The DVD963SA series offer progressive scan YUV outputs, and the option to select the interlace YUV output by a sliding switch on the board (selectable at the rear of the player). 9.5.
PAGE 71
Circuit Descriptions and List of Abbreviations DVD963SA 9. EN 85 Also, when going to Standby, the slave processor will reset the host processor. When the slave processor receives the correct IR (or key) code to leave the Standby mode, it resets the host processor. does not support this, an external circuit (two bi-directional switches, named switch "1" and switch "2") is added. The Yand CVBS-components also share the same pins.
PAGE 72
EN 86 9.8 9.
PAGE 73
Circuit Descriptions and List of Abbreviations 9.9 DVD963SA 9. EN 87 IC Data In this paragraph, the internal block diagrams and pinning are given of ICs that are drawn as 'black box' in the electrical diagrams (with the exception of 'memory' and 'logic' ICs). 9.9.1 Diagram Power Supply: TY72011P2 (item 7130 Vcc pin13 Startup HV 1 NC 2 UVLOh = 15V UVLOl = 7.
PAGE 74
EN 88 9.9.2 9. DVD963SA Circuit Descriptions and List of Abbreviations Diagram A2: AK4103VF (IC7203) CL 26532105_054.
PAGE 75
Circuit Descriptions and List of Abbreviations 9.9.3 DVD963SA 9. Diagram A3: CS4362 (IC7300) CL26532105_055.
PAGE 76
EN 90 9.9.4 9.
PAGE 77
Spare Parts List DVD963SA 10. EN 91 10. Spare Parts List Mechanical /001 0365 3103 308 92610 CABLE AUDIO 2X2RCA MALE 1.
PAGE 78
EN 92 2541 2542 2543 2544 2545 2546 2547 2600 2601 2602 2603 2604 2605 2606 2608 2609 2610 2612 2613 2614 2616 2617 2618 2619 2620 2621 2622 2623 2624 2625 2626 2627 2628 2633 2634 2635 2636 2637 2638 2639 2640 2646 10.
PAGE 79
Spare Parts List 3632 3633 3634 3635 3636 3637 3638 3639 3640 3641 4822 051 30222 4822 051 30759 4822 051 30103 4822 051 30103 4822 051 30103 4822 117 12902 4822 051 30183 4822 051 30101 4822 051 30222 4822 051 30689 3642 4822 051 30689 3643 3644 3645 3646 4822 051 30101 4822 051 30101 4822 051 30222 4822 051 30689 3647 3648 4822 051 30222 4822 051 30689 3652 4822 051 30562 3653 3655 4822 051 30103 4822 051 30562 3659 3661 3664 3665 4822 117 11151 4822 117 11152 4822 117 11151 4822 051 30689 3
PAGE 80
EN 94 6107 6200 10.
PAGE 81
Spare Parts List SCART PWB Various 1000 1001 1300 2422 025 12352 CON BM EURO H 21P F BK GRND-L 2422 025 12352 CON BM EURO H 21P F BK GRND-L 2422 025 16526 CON BM V 22P F 1.00 FFC 0.
PAGE 82
EN 96 11. DVD963SA Errata 11. Errata 11.1 Revision List 11.1.1 Manual 3122 785 12331 From production start, the new print layout of the Pscan board has been introduced. • In this service manual the circuit diagrams, print layout and the belonging parts list are added. In the manual 3122 785 12330, the Double Scart circuit diagrams and print layout was left out. • In this version of the service manual, the circuit diagrams and print layout are added.