These are verified as working codes, and have been collected from many different sources. Therefore have all not been tested, but please note I am not liable for any damage caused while you are messing on with your machine. Please perform these at your own risk! At the bottom of the page, there are some other codes for selected models. A-trend AD-L528 With the draw closed, and with no disc in it.
Acoustic Solutions DVD551 Switch machine on with no disc in it and Press "Set-up" on remote. Then push Press Next > Stop > Pause > Prev > Next. This will bring up Region ID, up arrow to "bypass" for all regions. Press "Select/play" for confirmation. Afreey ADV-2360 Turn on the ADV-2360 without a disc in and open the Player Tray, BUT you must use the remote control. Press SETUP on the remote to go to the set-up menu. Press in sequence the following buttons: ZOOM, PREV, NEXT.
"MENU" button on unit for over 4 seconds, while holding pressed that key, do the same with "TOP MENU" (now you have two buttons pressed) and finally do so with "OSD" / power button , hold then for at least 3 seconds and “FACTORY” should appear on the display. (you have to follow the sequence keeping pressed all previous keys) Turn on the unit In order to put it back to normal, use "F SKIP" instead of "MENU", "B SKIP" instead of "TOP MENU" and "POWER" instead of "OSD". "All Clear" should appear on display.
Press the Pause button on your Remote Control Using your Remote Control enter the code 3, 1, 4, 1, 5 and 9 Press the 0 button on your Remote for Region free, 1 for Region 1 or 2 for Region 2 Press the Pause button on your remote control Power off your player and wait a few seconds Power on your player Akai ADV-8000 To input, OPEN the disc tray and input 8-9-2-6 on the remote control. The numbers appear as **** on the screen. Choose a region by pressing the corresponding number. E.g. Region 1 - 1.
Where x = the Region. So 01081 is Region 1, 01082 is Region 2. and 01080 is Region free! Apex AD-600A Press the Setup button on your Remote Control. Using the onscreen menu, select the Preferences option. Press the Still / Step button on your remote control. Press the Prev button on your remote control. Press the Next button on your remote control. You will now enter the hidden setup page, where you can change the region code Apex AD-1000 Visit http://www.apexmodchip.
2. If the archive does not contain a file named U1100A6X.ROM then you have the wrong one. 3. Create a CD-R using the above file named U1100A6X.ROM. Use the following specifications: a. ISO9660 b. Mode 1 c. Track at once d. Close the CD 4. Power on the player without a disk in the drive. 5. Insert the upgrade disk you just created Picture 6. The display will switch to the first upgrade screen if the disk is correct Picture 7. The system will erase the firmware chip Picture 8.
1 and then 1 on your remote control, in order, one at time. Press the button 01 on your remote control to select Region 1, or 02 to select Region 2, and so on, or enter 13 to select Region Free. The word Region and then the number you selected should briefly appear on screen to confirm that the hack has been successful Arirang DH-9000 Open the DVD Player tray Press on the Remote Control 8, 9, 2, 6, x, where x = the desired region code Ariston DVD 2000 Code 1 On the players front press open.
SETUP. IN the remote control press NEXT, STOP, PAUSE/STEP, PREV, NEXT you should now see a new MENU. Go to Select Region and make your choice. Code 2 Ensure the DVD Player tray is empty and closed On the Remote control: Press Setup On the players Front Panel: Press Next Press Stop Press Pause / Step Press Prev Press Next You should now see a new Menu. Go to Select Region and make your choice: Axion DVD 2000 Code 1 Is the same hack as Mustek DVD V300 because the players are the same.
Bush DVD – 102 Press the Open / Close button on the Remote Control to open the drive tray. Press the buttons 2, 0, 0 and 1 on the Remote Control. Press the Enter button on the Remote Control You will now enter a hidden Setup page, and can change the player to any Region. To set it to Region Free Enter 13 as the country code. Bush DVD – 2000 Open the DVD Player CD tray. Place a Region 1 disc in the tray, but don't close it. Press the buttons 0, 1, 2 and then 3 on your remote control in order, one at a time.
Press Open. Press 3 then 3 then 0 then 8 then 8 then 0. Press Play. CCE DVD2100 Code1 Press the following button sequence on your Remote Control: Open/Close, Zoom, A-B, Up, Left, Down, Right. The words "Region Free" should briefly appear on the TV screen. Code 2 Open tray, Press 9 four times. The screen will show **** after you press 1111 and the Zone number you pressed after that. Classic DVD102 Turn on the DVD player with no disc in.
Open the Tray. Press "Clear" Button then Press 1,3,6,9. Select the Region code by pressing the corresponding 1-6 region code, or 0 for all. Close Tray and Switch ON/OFF. CyberHome AD-L 28 Code 1 Turn on your DVD player and open the tray. Press the stop button on your remote and enter 1999. A menu will pop up. Select the region code using the remote (set it to ALL). Confirm it, using enter and leave the menu using the return button on your remote.
button on your remote control Daewoo DHC – 2300 Press the Open button on your Remote Control Press the Setup button Press the 9 button for Region Free, or 1 for Region 1, 2 for Region 2, and so on Press the buttons 2, 0, 1 and then 0 on your Remote, or if this doesn't work, try pressing the buttons 3, 0, 1 and then 0 Press the Step button Press the Shuffle button Press the Next button Daewoo DHC-5800K Same as above Daewoo DHC-8000K Press the Stop button on your remote control 2.
player. Daewoo DVG-4000S EJECT, SETUP, STOP, I<< (PREV), >>I (NEXT) "FACTORY CONTROL PAGE" Menu will appear on the Screen. MOVE to REGION CODE with DIRECTION Button in the Remote Control and press PLAY. Press SETUP. Daewoo DVG-5000D Turn On, Press Open, Press Set-up, with remote, don't close the DVD plate in the whole process. Press Play on the remote. Choose TV Type in the menu with remote. Press Stop in the player (No remote). Press |< (Prev) in the player. Press >| (Next) in the player.
Dansai DVD852S Turn on the DVD player, with no cd in the player. Press 'set-up' on the remote. Press 'stop' on the DVD player. Pres 'Prev' on the player (top button). Press 'next' on the player (bottom button). In this menu you can set 'region' and turn on or off the marcovision Dantax DVD1000 Code 1 Open slide. On remote control, push 9926. On remote control, push 0 Close slide. Turn power off, and turn power on again after approx. 1 minute The DVD player will now recognize all regions.
Open tray drawer, Press 2918, Press ENTER (a manual will appear on the screen) Use up and down buttons to choose the region code, press ENTER (13 and ENTER for multizone), Press set-up. DiViDo Press (on remote): open - set-up - 9 - 4 - 0 - 1 - 0 - step - shuffle - next Turn on and off and all regions are supported. Dual 7000 MP Look at the Hack of Mustek V560 Eclipse DVD-595 Type 770 enter on the remote when in standby with no disc in machine.
Open the drive tray Key in using the Remote 8926# (Where # = Region number i.e. 1, 2, 4 etc. 0 = multi region and no Macro vision) Emerson EMD-2100 Code 1 On the remote press. Open, Set-up, 9 (for Multiregion) or (1 to 8 for each region), then 5010, step, shuffle, next Code 2 Look at codes for the Scan SC 2000. Encore DV450 Multiregion: press set-up and type 38883 on remote, then choose which region you want (1-6) or choose to bypass region settings.
Place an audio CD in the drive tray Press the Open button on the Remote to close the drive tray Press Menu, 1, Index (1-All) button Press the Open button Press the 1 button Finlux DVD-410 Don't insert disk, press set-up, stop, previous track and then next track. Now you are in the factory menu and you can set region and macrovision. Finlux DVD-510 Press: set-up, go to: general set-up press: play, go to: TV display, press: stop, |<<, >>|.
now Region Free. Genica GPX-DV2000 Eject the tray Key in on the Remote Control 2180 Enter the Region code 1-6 If you want all regions, press 9 To disable Macrovision: Open the players tray Key in from the Remote Control 4, 5, 6, 1 Turn Macrovision off by keying in 1, to turn it on again key in 0 Goodmans GDVD 100 With no DVD/cd in the tray press set-up->menu->step->prev->next gives access to a secret menu. Region bypass can be accessed.
The key region box will pop up Key in the region you want Press Mute Goodmans DVD-3500PK Open the player drawer Press 9, 8, 1 and 7 on the Remote You will now be in the hidden menu where you can change the Region from 1 to 6 by pressing Enter on the Remote. Selecting 9 sets it to Region free Govideo DVP855 Power unit "on", Press "open", Press "set-up", Highlight "custom", Press 3333 a new menu appears called "Secret1". Select region or choose "0" for region-free Govideo DVR4200 Code 1 Press pause.
Code 2 Turn the player on and ensure there is no disc in the tray From the Remote Control key in 0, 0 and Clear, for Region Free operation 0, 0, 1 for Region 1 0, 0, 2 for Region 2 and so on Gradiente D-22 Put the player into standby. Press 0, 0. For region 1 press '1'. For region 2 press '2'. For any other region press the corresponding key on the remote.
Same as above Grundig GDV 620HT Turn the machine on and open up the DVD tray. Using the remote control press 9817. Change the region to whatever you want or set it to 9 which is Multiregion, press the enter button. Or Power on, and open drawer. Key in 3838 with handset. A menu will appear,"Region Code",and "Macro On/Off".
Power on your machine Press the Stop, Open/Close and Skip buttons on your player simultaneously and hold down for 3 seconds A hidden menu should appear.
will appear next to it. 13. If the word reads "none" then forget the whole thing, as you are already region free... if there's a number there then that is the region your unit is using. 14. Press "ok" on the remote to change the region. 15. Use the down button [directly under the "ok" button on the remote] to scroll down the list. 16. Select the word "none" to make your unit region free. 17.
Haus H-2001-S (Press "STOP" twice. Press "SETUP". Press "VOL+ & VOL-" repeat the sequence twice in quick secession (+,-,+,-). the TV screen will display "VER #" Press left/right cursor keys to change the # -(1,2,3,4,5,6 for desired Zone Code) For All Code -Press 255. Press "SETUP" . The system Zone setting is then completed. Haus H-615L-S 5.1 At Logo screen, press [STOP] key. Input the digit number in the sequence [2,3,1,7]. Then input the region code, 0 for all, Power off the DVD player .
You will now need to select a language option between 1 and 6 To convert this player to Multi-Region playback: Press the Repeat button on the Remote Control Using the Remote enter the code below, note that you must know what Region your player is currently set to in order to know which code is appropriate For Region 1 use 2, 9, 3, 3 and 4, For Region 2 use 3, 8, 7, 6 and 7 For Region 3 use 5, 6, 7, 3 and 2, For Region 4 use 7, 6, 8, 8 and 4 For Region 5 use 5, 3, 8, 1 and 4, For Region 6 use 2, 4, 4, 6 and
Power on your player whilst pressing both the Play and Stop buttons on the front player After a short while you should be presented with a set of language options.
To change the region code of this player just open the DVD tray and press 1 four times on the remote control followed by selecting desired region code 1 2 3 4...
With the tray empty, select the Menu, press 9, Open/Close, then 5, Select region 1-6, Mute. JNL Digivision 7001 Open the tray. Input the numerical sequence 2180 followed by the zone number of the software you wish to play. This is shown on the DVD as number inside a world globe. (Use 9 for multizone). Close the tray. To disable macrovision, open the tray. Input the numerical sequence 45611. Close the tray. To reset Macrovision protection input 45610 and close tray.
Make sure there is no disk in the tray. Unplug mains AC. on the unit press and hold "play" and "open/close". While holding these keys plug in mains power. Release these keys and test appears on the display. Press "3D-phonic". Press menu twice on the remote. Display reads 000 5858 use down buttons to 000 to 02e 9 change last 4 digits to the following 0000 for region free 0101 for region 1 0202 for region 2 press enter on the remote. Press standby and wait 5 seconds.
Switch it on Press Setup Press Slow Press Skip left Press Skip right Use the Right Arrow button to select the desired region: A = Region 1, B = Region 2, C = Region 3, D = Region 4 E = Region 5, F = Region 6, *** Region Free Press Setup Kiss DVD 1502 Switch it on Press Setup Press Slow Press Skip left Press Skip right Use the Right Arrow button to select the desired region: A = Region 1, B = Region 2, C = Region 3, D = Region 4 E = Region 5, F = Region 6, *** Region Free Press Setup Kiss DP-330 On Remote
Open Tray, press 6,6,6,6 then Select on the remote. Scroll down to Country code and set it to "13". Press Select then return to exit. Konka KD-1900 Turn on player and open tray On the Remote key in 6, 6, 6, 6, Select A hidden menu will appear on your TV screen 'D-1800 System Setup' Use the directional buttons to scroll down to 'Country Code' Press Select on the Remote and change the setting to the Region Code you need, 1 thru 6.
If you get an "invalid region" message on screen simply open up the DVD drawer an press 1 1 1 1 followed by the required region Or Press the Open/Close button on your remote control, A-B, Up, Left, Down, Right. Region free should flash up. Lasonic DVD-2100 Open disc tray and leave it open. Press set-up, press Vol.+ then Vol.-, Press Vol.+ then Vol.again. Top right hand corner will appear reg.1 and use the blue arrow on the remote to choose which region you want or select ver.255=meaning all region.
LG 2300 With "no disk" on tray, press sequentially in the remote control PAUSE,3,1,4,5,9: code -- will appear in the display. Enter the region or 0 for region free. LG 3000 Press the Pause button on your remote control. Using your remote control enter the code 3, 1, 4, 1, 5 and 9, Press the 0 button on your remote control for Region free, 1 for Region 1 or 2 for Region 2. Press the Pause button on your remote control. Power off your player and wait a few seconds.
Turn the machine ON and remove any discs. When the display shows 'NO DISC' Enter 'Play', '159'. The display will change to show 11 dashes ('-----------'). For region 1 enter the 12 digit code '005000128156', for region 2 enter the 12 digit code ‘002000128156’ Press 'Play' and the screen will turn red and then reset.
Marantz DV-3100 Turn on without disk and wait for "No Disk" on front panel display. On front panel, press and keep pressed Pause, while you enter 3,1,4,1,5,9 on remote. Release Pause immediately after the "9". The word COdE is displayed on panel. Press number of region, or 0 for all regions. Press Pause on panel again Marantz DV-4000 Turn the power off, Keep holding [DIMMER] and [Previous] key together and switch power on.
Press Press Press Press Menu. 9. Open/Close. 5. A service menu will now appear enabling you to change the region. Medion MD-7950A Switch the player on at the base unit Open the drawer and leave open Using the handset type in 8, 9, 2, 6 then the required region code (1 for R1, 2 for R2 and so on...) Close the drawer with the required DVD in Press Play Memorex MVD-2027 "SETUP", Press "1" for region 1 or press "2" for region 2 Press "7" for all regions, "PAUSE/STEP", " >>I ", " I<< ", "SETUP".
Switch it on Press Setup, Slow Press Skip left, Press Skip right Use the Right Arrow button to select the desired region: A Region 1, B Region 2, C Region 3, D Region 4 E Region 5, F Region 6, *** Region Free Press Setup Mustek DVD V520 With the draw empty, Press setup, then previous, next, previous, next, previous, press right cursor until 255 appears and finally push set-up.
With remote:- open draw, press set-up, stop, back skip, fwd skip. Now in hidden menu turn macro off and change region to 0. Nakamichi DVD-10S Press power+dimmer+previous (|<) all together the display’s shows _ _ _ _ . Press in sequence 1 9 9 9, the display shows A-0000 D-01 and Enter region code. Power off.
Omni SL-P2002KD To turn this player in multi-region mode: Turn on the Player Open the tray Enter the following code from the Remote 2, 1, 6, 8, 9 Play your DVD Optim DS-8302 Open tray and Press Intro then 0 7 1 2 1 or Older firmware may use 0 7 1 2 0. Orion DV-KT Simply turn on the player with no disk loaded, Hold open/close, stop and skip right and wait about 5 seconds. Chose region number or Set to Free.
Same as above Oritron DVD650 Same as above Oritron DVD-1030 Ensure the tray is empty Press 'Menu' Press '9' Press 'Open/Close' Press '5' 'Region 1 - 6' should be displayed on screen Enter Region code Press 'Mute Oritron DVD-200 Dia Same as above Pacific PDVD-1000 Open tray, enter 8421, press enter until you get to no.9, close tray. Palsonic DVD-3000 Insert any disc, select the PBC button on the remote control, then followed by selecting the play button.
Philco PH-7000 Press "set-up", "Pause/Still", Press "Prev", Press "Next". Then Select -->REGION then -->BYPASS. Philco PH-7100 Turn on the player Press Eject on the Remote Control Press 7, 4 followed by Enter Key in the Country Code 1, 3 followed by Enter Press Play Put a DVD in the tray Press Play You may be able to select a specific Region by keying in the Region you desire, i.e. 1 for Region 1, 2 for Region 2 and so on, instead of using code 13.
Philips DVD-612 Same as above Philips DVD-700 To convert this player to play a Region 1 disc: Press Play, 2, 7 and 4 on the Remote Control. The onscreen display should then look like this: '____ ____'. Enter the following code using the Remote Controls number pad 005000 128 256. Press the Play button on the Remote Control. The onscreen display should turn red, indicating that your region settings have been changed.
Press the OmniRemote key marked as 955 Multizone The onscreen display should show 11 spaces like this: '-----------' Using the number keys on your DVD player's Remote Control, enter the code 222 222 005 255.
outputs all vary 1. Turn the machine ON and remove any discs. 2. When the display shows 'NO DISC' 3. Enter 'Play', '159'. 4. The display will change to show 11 dashes ('-----------'). 5. For region 1 enter the 12 digit code '004000128156', for region 2 enter the 12 digit code '003000128156' 6. Press 'Play' and the screen will turn red and then reset. Philips DVD 953 Press System Menu, Select TV Aspect. Place the cursor on 16:9 wide. Enter 1 3 9 7 1 3 9. Press Ok in control, Press System Menu to exit.
the screen will turn red and then reset. Philips MX1060D Open Drive, Press System. Press 1 6 7 (in sequence) and you should now asked to select a region. Phonotrend Prestige 2200 Power on the unit and open the DVD door by press, ”open" button on the front panel. Use remote input ID number 33088. You will see on the top left of the screen appear "****" . Then add one more digit after 33088 according to regional code.
Then input the number of the zone you want. Playstation 2 (Jap) Code 1: Press & Hold the Circle, Right and L1 keys. Code 2: Press & Hold L3 & push the stick in hard Code 3: Boot into PS2 browser without a CD in the tray Insert the Region 1 DVD you want to play Press Circle and R1 on the DVD Hold Right until menu appears Press Circle and R1 again NOTE: This hack only works on the first revision of the PS2 (SCPH-10000).
Press the buttons 0, 1, 2 and then 3 on your remote control in order, one at a time. Press the play button on either your remote or the player. To change the player back to Region 2 only functionality: Open the DVD players tray. Place a Region 2 disc in the tray, but don't close it. Press the buttons Return and then Play on your remote control in order, one at a time. Proline DVD2000 Code 1 Make sure the draw is empty and closed.
E Region 5, F Region 6, *** Region Free Press Setup Rankarena DVD2400 Code 1 Without any disc in player press, Setup, Mute, Last, Next on the RC. Choose region Code 2 To enter Loophole-Menu: Ensure there is no disc in the players drawer On the Remote Control press Setup Then Mute Then Last Then Next RCA DRC220N Press menu, 1,6,7 then mute to play all regions REC 850 Switch on the player and Open the tray. Push 'stop' and enter numerals 1 9 9 9.
Roadstar DVD-2027H Open the drive tray. Make sure there's no DVD in it then Type 9 8 1 7 or 8 4 2 1 on the remote keypad. You will then be into a hidden menu and Choose regions 1-6 or 9 for region free clicking SELECT (Enter) button. close the tray. Turn the player off for few seconds. Turn it on again. Rowa DVD-280 Press, open/close, zoom, a-b, up, left, down, right. Or Turn the player on without a disc in it or disc tray open.
Press the Setup button on your remote control. Using the onscreen menu, select the Preferences option. Press the Still/Step button on your remote control. Press the Prev button on your remote control. Press the Next button on your remote control. You will now enter the hidden setup page, and can change the player to any Region or set it to Region Free Sampo DVE-611 Create a txt filed called CREGIN.TXT, Put this is the txt file TSDVDREG-2001-9629735-R0.
which code is appropriate for Region 1 use 2, 9, 3, 3 and 4 for Region 2 use 3, 8, 7, 6 and 7 for Region 3 use 5, 6, 7, 3 and 2 for Region 4 use 7, 6, 8, 8 and 4 for Region 5 use 5, 3, 8, 1 and 4 for Region 6 use 2, 4, 4, 6 and 2 A code should be displayed on the screen indicating the current Region setting of your unit. Press the 9 button on your remote control for Region free, or 1 for Region 1, 2 for Region 2 and so on. Press the Open button on your player.
Switch the player off and on. Hold the play and stop buttons (for 10 seconds). Press the Repeat button on your remote control.
Always perform a Cold Start before applying the hack below: Power on your player whilst pressing hold both the Play and Stop buttons on the front player After a short while you should be presented with a set of language options. Release the Play and Stop buttons on the player You will now need to select a language option between 1 and 6 Sansui DVX 2100 Turn on, eject DVD (leave open), press 2,9,1,8, or 2,8,1,2 then enter, and you are in maintenance menu.
Schneider DVD-511 Converting this player to all region: Press the Menu button on the Remote Press the 1 button Press the 6 button Press the 7 button Press the Mute button Schneider 810 On remote, Press menu, 9, open/close, 5. Region selection page is shown Press mute Schneider 855 Turn on DVD. Open cd drawer. Press set-up on remote. Press right button until all way across. (Should relate to passwords. press button (3) four times. (This will bring up region select). press right to highlight regions.
Press 1, 2, 3 you'll find a "LOOPHOLES" menu (the software politely reminds you that "YOU SHOULDNT BE HERE"). There is a Region menu and Macrovision menu plus others (CSS, AUTOMUTE, AUDIODITHER) Use this menu with care as you could screw up your machine! My advice would be to make sure you know the hard reset functions for the unit. Sharp DV-654Z When the player shows the map screen and say "cannot play on modified region 1 players".
Code 1 Ensure the player’s tray is open. From the Remote Control, Press 7, Press 4, Press Select or Enter, Proceed as per usual. Change the "COUNTRY CODE" (Region code) to 13, this will set you to Region free Code 2 Ensure the players try is closed and has no disc in it From the Remote Control Press 7 Press 7 Press Select or Enter Singer SGD-006P Open Drawer. Press 8, 4, 2, 1 to bring up hidden region menu. Press the select button until region 9 is selected.
SM Supervision 2500 Open the tray, type 8421 or 9999 (both work) on the remote. Press the OK-key until the region code you want appears (9=code free). Close the tray – finished. Smart DVD2000 Open the disc tray, press 0, 7, 7, select, and a menu should appear. Change 'Country Code' from 13 to the right region, press play. SMC 330S, SMC 530 Open Tray, Press 2-0-0-1-Select on remote and a Maintenance Menu appears from where u can change the region Or Open the tray. Press 7,7, Select.
Insert your disc then press DVD menu button, should take you to menu screen for the film, Then select program button on your remote then selected a few chapters from 2 - 20 say then press play,stop,play,stop until it plays the movie(sometimes works straight off others minutes, it may start playing at chapter 15 but once you have it playing just skip back to the beginning.
Press Circle and R1 again NOTE: This hack only works on the first revision of the PS2 (SCPH-10000).
Thomson DTH-4200, Thomson DTH-4500, Thomson DTH-5000, Thomson DTH-5200 Code 1 Press the Repeat button on your remote control.
This may be a possible to bypass the RCE (Regional Code Enhancement) protection on The Patriot on the Toshiba range of DVD players. This is specifically for the SD-100E however may well work on other players: Insert the disc and wait for the RCE screen to appear Press 'Memory' on the remote control Enter title 01, chapter 00 Press Enter This should play the film.
Turn the machine on and open up the DVD tray. Using the remote control press 9817 or 3838, and the magic menu appears. Change the region to whatever you want or set it to 9, which is Multiregion - press the "ent" button until it matches your choice. You can also alter macrovision from this menu. Venturer STS32S Turn machine on by power on button not from stand by. Open drawer, while drawer is open. Type in 9,8,1,7. Press ENT. Until you reach region 9, then press RETURN.
Code 1 Press "open tray" then Press "33080" for multizone or "33081" for region 1 or "33083" for region 3 etc. press "close tray" Code 2 To change the player Region code follow the below steps: Open the players draw Key in using the Remote 8926 followed by the Region code your require, i.e. 1 for Region 1 etc. Keying in 0 sets the player to Region free mode and reportedly disable Macrovision Xwave LB 900, Xwave LB 1000 Power on the DVD without any CD inside.
Yukai DVD-V300 Code 1 Ensure the players tray is empty and closed On the Remote control: Press SETUP On the players Front Panel: Press NEXT Press STOP Press PAUSE/STEP Press PREV Press NEXT You should now see a new MENU. Go to Select Region Code 2 This is the same hack as Mustek DVD V300 because the players are the same.
On the remote press 0, 1, 2, 3, PLAY The tray should then close, if not close it, and the player is now completely region free Code 2 Multi Region Hack Power on the player with no disk in the drive Press PAUSE on the Remote Enter 3, 1, 4, 1, 5, 9 on the Remote (the word COdE appears on the display) Enter 0 on the Remote (0 = All Regions, 1 = Region 1, 2 = Region 2, etc.
