Service Manual Issue 1.
DV29 Contents List Circuit Description Power Supply L959AY ! CCT diagram ! Component layout diagram ! Parts list Main Board L971AY ! CCT diagram ! Component layout diagram ! Parts list Display Board L972AY ! CCT diagram ! Component layout diagram ! Parts list Transformers ! L924TX ! L925TX ! L931TX Mechanical Assembly ! Mechanical and packing part list
FMJ Dv29 Circuit description. Overview The DV29 is effectively a no compromise version both electronically and mechanically of the DV79. The player is based around acclaimed Zoran Vaddis V chipset coupled to high specification Wolfson D to A converters for all six audio output channels, also featured in this design is a HDMI transmitter with digital Video and a Audio output capable of Digital Surround.
The DV29 uses a separate isolated Toroid transformer and Rectification stages based around Bridge rectifiers DBR1000 and DBR1001 and bulk smoothing caps C1048 and C1049 to supply the Analogue stages the smoothed D.C output from this stage is fed L1013 (+) and L1015 (-). Regulator REG1001 is fed from the +15V3 rail and forms the Audio DAC supply.
Display Board interface Flash/ SDRAM The display board interface is on the 16 way FFC flexi foil connector at location CON202. Power for the display also travels on the connector. There are 4 ā wires to interface with the VFD driver chip these are seen as. IC203 is a 64Mbit (32 bit x 2Meg) SDRAM. It runs at 135MHz o o o o XFPDIN - Data to the display board FPDOUT - Data from the display board XFPCLK - Clock XFPSEL - Chip select The above control lines are level shifted to 5v logic from 3.
Fig 3.
Left and Right channel D to A stages The Wolfson WM8740 stereo DAC requires +5V(A) and a +3V3 supply along with the Digital Audio data lines already described in this guide. The Left channel output only will be described in this section as all audio output stages are the identical (all six channels of a DV79) apart from the HDCD gain switching for L + R only.
HDMI output stage Please note: Due to the plug and play nature of the HDMI/DVI interface, if presented with a reported no HDMI problem it is worth checking all set-up parameters of both the DVD player and the Plasma/Projector in use before performing component level diagnostics on this section. HDMI is a system that transmits uncompressed digital video and digital audio over a high speed encrypted interface.
Comms and Final video output stage The signals from the main board travel up to the Comms board on connector CON902. The Video signals simply travel via an A-C coupling net before exiting the player via the RCA-phono sockets at locations SKT902 and SKT903. The RS232 interface is on 9 way āDā type CON900, with IC900 providing the level translation and static protection between the RS232 levels and the 3.
DGND 1 L C2 2 L1 250U 1 E SW1 18-000-0019 C4 3N3 250V CER NF 2B 2 115V 230V TX1 Small Toroidal Mains L924TX 115V FHLDR1 20mm HLDR D1 2KBP02 5 2 FS1 T315mA R1 22K 0W25 MF C5 3 6 C27 1000UF 63V YK 115V FHLDR2 20mm HLDR 4 BZX79C 2V7 DO-35 NF 6 2 5 1 4 GREEN 2 GREY 1 GREY 1 4 GREY 3 DK GREY 2 LT GREY 1 BLUE CON1 3 1N4148 DO-35 VN13V5_F1 DZ4 BZX79C 5V6 DO-35 R2 AC_PRES* C31 22UF 63V YK TR2 CON2 WAGO 256 CON3 WAGO 256 C6 100N 100V MKS2 0R0 0W25 MF C7 100N 100V MKS2
DV29 DVD player PSU board L959AY issue 1.1.
L967C10 L971C10.Sch POWER SHEET 10 PSUCLK AC_PRES* AC_PRES* L967C4 L971C4.Sch L967C2 L971C2.sch GAIN_SCALING RESET* MD MC ML_8740_0 ML_8740_1 ML_8740_2 FSEL0 FSEL1 PSUFS0 PSUFS1 ADAT0 ADAT1 ADAT2 ABCLK ALRCLK SPDIF MUTE* CLK27M_VADDIS MCLK_VADDIS AC_PRES* GAIN_SCALING RESET* MD MC ML_8740_0 GAIN_SCALING RESET* MD MC ML_8740_0 ML_8740_1 ML_8740_2 L967C3 L971C3.
FRONT PANEL RESET +3V3D FPDOUT XFPCLK XFPSEL XFPDIN REM_BUS_P IRRCV VCC 21 24 66 65 64 63 62 61 60 27 26 25 PR219 RAMDQM 16 71 28 59 44 VSS 58 VSS 72 VSS 86 VSS address data address FRAMDAT5 FRAMDAT6 FRAMDAT11 FRAMDAT10 RAMDAT9 RP201A RAMDAT8 RP201B RAMADD9 RP201C RAMADD8 RP201D 1 2 3 4 8 7 6 5 56R 56R 56R 56R FRAMDAT9 FRAMDAT8 FRAMADD9 FRAMADD8 RAMADD7 RAMADD6 RAMADD5 RAMADD4 RP202A RP202B RP202C RP202D 1 2 3 4 8 7 6 5 56R 56R 56R 56R FRAMADD7 FRAMADD6 FRAMADD5 FRAMADD4 RAMADD3 RAMDA
CLOCK GENERATOR REG300 LM1086CS-3.3 +5VD +3V3 TO-263 C342 C303 C306 C311 C308 100N 16V 0603 100UF 10V YXF 100N 16V 0603 100N 16V 0603 100N 16V 0603 DGND 1 DGND +3V3D DGND P356 2 SD D CLK 13 Q 8 R308 100R P357 9 0603 P348 R323 74LVC74AD S0-14 100R 8 10 10 11 1 P346 ENABLE_AV SO-14 4 2 P347 IC303A SN74AHC1G00DBVR DBV-5 DGND 47R 0603 19 11 IC307D 74LVC125AD P318 P319 P320 OE 75R R322 47R 0603 MCLK_DAC1 P327 Fs FSEL1..0 44.1kHz 48kHz 88.2kHz 96kHz 176.
+12VA OUTPUT BUFFER Audio outputs are inverted so as to be compatible with DV88. This is compenstaed for in software by setting a register in the DAC to invert the signal Gain of -2.2 for HDCD, otherwise -1.
Audio outputs are inverted so as to be compatible with DV88. This is compenstaed for in software by setting a register in the DAC to invert the signal ALL PARTS ON THIS SHEET ARE NOT FITTED FOR DV75 +12VA OUTPUT BUFFER Gain of -1.
+12VA Audio outputs are inverted so as to be compatible with DV88. This is compenstaed for in software by setting a register in the DAC to invert the signal OUTPUT BUFFER ALL PARTS ON THIS SHEET ARE NOT FITTED FOR DV75 Gain of -1.
SCART_RIGHT AUDIO SCART_LEFT C800 47P 100V 0805 C801 47P 100V 0805 R800 0R0 0W125 0805 DGND SCART_BLUE VIDEO SCART_GREEN SCART_RED SCART_COMPOSITE C802 47P 100V 0805 C803 47P 100V 0805 C804 47P 100V 0805 SCART OUTPUT C805 47P 100V 0805 SCART_RIGHT 1 2 SCART_LEFT 3 SCART_AGND 4 5 6 7 SCART_BLUE 0/6/12 8 9 10 SCART_GREEN 11 12 13 14 SCART_RED 15 RGB_STAT 16 17 18 SCART_COMPOSITE 19 20 21 DGND SCART control signals ENABLE_AV: 0 in when standby mode, 1 when on (3V3 levels) (RGB_STAT is supposed
DGND DISPLAY BOARD SUPPLIES L1006 -19V 100N 50V 0805 L1009 P1024 120R@100MHz M3 R/A PCB FIXING BRACKETS ITEM1002 C1008 120R@100MHz P1007 4 1 3 2 SH1000 1 ITEM1004 4 1 3 DGND 4 EMC CAN 2 NF -19V_OUT L1004 P1001 -9V P1022 120R@100MHz FIX1009 P1005 120R@100MHz FIX1010 Dia 3.5mm -13V5 L1008 P1023 120R@100MHz 1 3 2 EMC Shield 1N0 50V 0603 1N0 50V 0603 Dia 3.5mm 1N0 Dia 3.5mm 50V 0603 NF DGND 120R@100MHz Dia 3.5mm 1N0 50V 0603 1N0 50V 0603 Dia 3.
REG1100 LM1086CS-3.
ON SNAP-OFF PCB THESE PARTS NOT FITTED FOR DV75 +5VDA C911 C902 100UF 25V YK 100N 50V 0805 FIX900 FIX901 1 1 Dia 3.5mm Dia 3.
+5V_VID +5V_VID 1 SD 3 100N 16V 0603 ADP3333ARM-2.5 MSOP-8 C717 C702 100UF 10V YXF 100N 16V 0603 L700 P700 R700 560R 0W063 0603 Decouple each VDD,VAA & VDD_IO pin with 100n+10n close to pin +3V3D C720 6P8 50V 0603 C701 C713 100N 16V 0603 Progressive scan mode: VIDP[0..9] = 10 bit multiplexed Cb,Cr data (bit 0 = lsb) VIDP[10..
DV29 DVD player Main board L971AY issue 1.0.
DV29 DVD player Main board L971AY issue 1.0.
DV29 DVD player Main board L971AY issue 1.0.
DV29 DVD player Main board L971AY issue 1.0.
DV29 DVD player Main board L971AY issue 1.0.
DV29 DVD player Main board L971AY issue 1.0.
DV29 DVD player Main board L971AY issue 1.0.
DV29 DVD player Main board L971AY issue 1.0.
DV29 DVD player Main board L971AY issue 1.0.
DV29 DVD player Main board L971AY issue 1.0.
DV29 DVD player Main board L971AY issue 1.0.
DV29 DVD player Main board L971AY issue 1.0.
DV29 DVD player Main board L971AY issue 1.0.
DV29 DVD player Main board L971AY issue 1.0.
DV29 DVD player Main board L971AY issue 1.0.
SW6 SDTM-610-NTR R13 1 2 PLAY 10K 0W125 0805 SW3 SDTM-610-NTR D2 P6 SW2 SDTM-610-NTR SW4 SDTM-610-NTR |< SW5 SDTM-610-NTR 2 D3 SW9 SDTM-610-NTR 2 1 1 2 TR5 MMUN2111LT1 SOT-23 BC849B SOT-23 P13 D4 R4 220R 0W125 0805 NF S6 BAS16 SOT-323 K4 P22 K3 P21 +5VD TR4 S5 BAS16 SOT-323 P23 K2 P11 >> PAUSE P19 ON/STBY*_LED +5VD P10 IR/LED SNAP-OFF BOARD S4 BAS16 SOT-323 LOAD 2 1 2 << 1 SW8 SDTM-610-NTR 1 10K 0W125 0805 S3 BAS16 SOT-323 STOP >| 2 2 1 1 2 NAV R
DV29 DVD player Display board L972AY issue 1.1.
Transformer Specification for 115/230V 50/60Hz mains transformer. Arcam Part Number L924TX The transformer is extremely cost sensitive. It is to employ the most cost effective techniques to achieve the specification. The transformer output voltage will be regulated by a switch mode power supply. 330MM The only essential specification is the fact that it must produce no acoustic noise either internally or by induced eddy currents in steel chassis etc..
WINDING DETAILS NOTE. TRANSFORMER IS TO BE USED ON SECONDARY SIDE OF MAINS ISOLATION BARRIER (I.E. THIS TRANSFORMER IS NOT REQUIRED TO PROVIDE MAINS ISOLATION BARRIER) MAXIMUM VOLTAGE BETWEEN WINDINGS <60V WINDING TURNS PRIMARY2 16 ENAMELLED COPPER WIRE SCREEN 2 VIEW FROM SIDE OF PART SHOWING OUTER FOIL SCREEN SECONDARY1 OUTER SCREEN 41T 6 1 PRIMARY1 16T 2 PRIMARY2 16T 3 SECONDARY2 11 22T 12 SEE VIEW GIVING PIN LENGTH DIMENSIONS 9 14T 10 SECONDARY4 0.8mm 0.
Transformer Specification for 100/115/230V 50/60Hz mains transformer (for audio) Arcam Part Number L931TX General Safety specification. --------------------------------------------------1. To standards BS415 / EN60065 - Class I / EN60742 Ferrite core WURTH 74270062 (or equivelant). Secondary wires pass through ferrite. Heatshrink tubing fitted over ferrite, but not firmly to cable, so that ferrite is free to move along cable 220MM, +20, -0 2.
!"#$%&'()*+,(*-%*+.%/*(0,+1%/*234%-,43 !'4,1+*352 6*23 !"#$%& 0123451 !"$=%& 0!C35CD 0522 LN=4 LN=N !"N$1< 0&=%D 0L=35$D 01=14ND !N4#1Y &$Q$1Y 0&C\1 %&4Q" &$N=9J &$C4\1 &$CN\1 &$C2\1 !"NN<,4 LNNC &"Q#\1 DN54= !$4$<, 012345D !$Q2,\ L5== 0`=1551 01CI=Q1 LN=2 &$#N1Y &$C=\1 &$#41Y &$249J 01CI=51 01235C1 !N2C1Y &$N"\1 !$"=%& 01214C1 LN2Q 0&21D !'4(2,/3,5+ &'()*+,-.+%/'/) ,+%67)8+9-7:+,2:45,,+%9+;< &'()*+>3>+&?6)@A?@B %67)8+%E/F+9-7:+G-HC:C,,+D&I ,2J4",,+D7'AA+GK<*/).
!"#$%&'()*+,(*-%*+.%/*(0,+1%/*234%-,43 !'4,1+*352 6*23 !"NN3>+Z)R-/)+\-@/7-*+\Z=4Q <-*[+D'B+45:4=+^7?FF'+%)'*+\*)'7 <7-.X6/+Z)B?A/7'/?-@+\'7. !@P)*-F)+L-7+Z)B?A/7'/?-@+\'7. <*'?@+WX/)7+\'7/-@+L,`+13" T@/)7@'*+<7?@/).+\'7/-@+L,`+13" \'7/-@+&'()*+L,`+>3N$ 0'@.(--U+L,`+>3N$+>3>+<*'[)7+,X*/? T@/)7/)U+&?A/?@B+&'()*+]F7?@/).
ARCAM All parts can be ordered via spares@arcam.co.