DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:36 Page 1 Quick start guide The pilot key allows you to browse the menus. Up right in the menus & options. Press to go left in the menus and down to go to select a menu or an option and validate a setting.
DECT613_GBIE_part1_07_09_04.
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:36 Page 1 Icons on the handset display The display gives information about the operation of your telephone On first use, it is sometimes necessary to wait for a few minutes of charge before seeing icons on the display. When charging, the battery bars scroll from empty to full status. When the handset discharges, the battery shows the status : and empty . Full , 2/3 , 1/3 The answer machine is activated (DECT 617).
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:37 Page 2 base station Paging key The paging key enables you to locate a missing handset. Press the key until the handset starts to ring. Once retrieved, press any key on the handset to end paging. base station Loudspeaker New message indicator When blinking, it indicates that there is a new message. When fast blinking, it indicates that the answer machine memory is full.
DECT613_GBIE_part1_07_09_04.
DECT613_GBIE_part1_07_09_04.
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:37 Page 5 Menu structure By using the “Pilot key” SMS on the side of the handset, you can scroll through the menus.
DECT613_GBIE_part1_07_09_04.qxd Answer machine 07/09/2004 Saved messages 16:37 Page 6 Play Next Previous Call Delete Store Send SMS Record a memo Outgoing messages Answ. machine mode Answer and record with personalised OGM Answer only with personalised OGM Answer and record with predefined OGM Answer only with predefined OGM Record outgg msg Standard OGM for answ.
DECT613_GBIE_part1_07_09_04.
DECT613_GBIE_part1_07_09_04.
DECT613_GBIE_part1_07_09_04.qxd Base station 07/09/2004 16:37 Page 9 Enable registration Line settings Dial mode Tone / Pulse Recall type Short flash / Long flash Choose country/oper. First ring On or Off Service code settings 11 Menu structure http://www.philips.
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:37 Page 10 Conformity,Environment and Safety Safety information This equipment is not designed to make emergency calls when the power fails. An alternative has to be made available to allow emergency calls. Conformity Hereby, Philips declares that the DECT 613xx and DECT 617xx are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:37 Page 11 Declaration of conformity We Philips Consumer Electronics Route d’Angers 72081 Le Mans Cedex 9 France Declare that the products DECT 613xx and DECT 617xx are in compliance with the Annex III of the R&TTE-Directive 1999/5/EC and then with the following essential requirements: Article 3.1.a (protection of the health & the safety of the user) : EN 60950-1 (10/2001) Article 3.1.
DECT613_GBIE_part1_07_09_04.
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:37 Page 13 Installing the base station Situate your product close enough to the telephone and mains power sockets so that the cables will reach.To properly install the base station, plug the line cord and the power cable into the base station. Plug the cord and the cable into the wall. A beep indicates that the phone is properly installed (only available for DECT 617).
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:37 Page 14 Introduction Philips screen saver After 2 minutes of inactivity, the screen saver is displayed: You can deactivate it (see p.30) Idle mode In idle mode, the DECT 613/617 display shows various information: - The date & time, the name of the handset and the instructions to access the menu. - Missed calls , new SMS or new messages or network voicemailbox message - “Do Not Disturb” mode (answer machine) , if any.
DECT613_GBIE_part1_07_09_04.
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:38 Page 16 In call features During an external call, some other options are available. Press to enter Options.
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:38 Page 17 Editing systems Case mode By default, the first letter of a sentence is in upper case. Use to change the case mode: - all letters in upper case (AB) - all letters in lower case (ab) or - the first letter in upper case and the rest of the word in lower case (Ab). Punctuation and mathematical marks are available through characters are also available on and while other special (see table page 20). Scroll to move the cursor left or right.
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:38 Page 18 Let’s compare Multitap and Eatoni® systems to write “Peter”. Keypad Keys Multi-tap Sequence [space] 1 @ _ # = < > ( ) & ¤ £ $ ¥ [ ] { } ¤ § To write “Peter” with multi-tap 1 abc2àäçåæ 2 Press once : P def3èé ) N 3 ghi4ìΓ 4 Press twice : Pe jkl57 5 mno6ñòö Press once : Pet 6 pqrs7ß A 2 E 7 Press twice : Pete tuv8ùü 8 wxyz9 f S Ξ Q 9 Press three times : Peter .0 ,/ :;" ' ! ¡ ? ¿ * + - % \ ^ ~ | 0 To write “Peter” with Eatoni® Long press Press to
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:38 Page 19 SMS menu is also accessible via the carousel or Important information are also available on the SMS leaflet in the box SMS Send new SMS Read SMS SMS settings SMS stands for Short Message Service.To benefit from this service you must subscribe to the Caller Line Identification Service (CLI) together with the SMS service from your network provider.
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:39 Page 20 Read SMS The SMS list contains the stored and received SMS. The received SMS are shown by and the stored SMS are shown . To read an SMS/to view the number Press to directly reach Send new SMS Scroll to Read SMS and select Select your SMS box* (only if you have created several SMS boxes).
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:39 Page 21 To reply to an SMS Press to directly reach Send new SMS Scroll to Read SMS and select Select your SMS box* (only if you have created several SMS boxes).
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:39 Page 22 To send again Press to directly reach Send new SMS Scroll to Read SMS and select Select your SMS box* (only if you have created several SMS boxes).
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:39 Page 23 To call from the SMS list Press to directly reach Send new SMS Scroll to Read SMS and select Select your SMS box* (only if you have created several SMS boxes).
DECT613_GBIE_part1_07_09_04.
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:39 Page 25 To set the SMS centre number(s) The SMS are sent through a centre.To receive an SMS from another operator, you must set the corresponding numbers. Press to directly reach Send new SMS Scroll to SMS settings and select Scroll to SMS centre and select Choose an SMS centre and select Scroll to Edit incoming number and select Enter the number and press OK Scroll to Edit outgoing number and select Enter the number and press OK SMS 27 http://www.
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:39 Page 26 Handset Babysit mode Registration Rename handset Date & time Display contrast Backlight Screen saver Babysit mode if there are at least 2 handsets This feature allows you to monitor the baby’s room. Place the handset in the room to be monitored and you will hear the noise coming from the room on the additional handset.
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:40 Page 27 Scroll to Registration and select Scroll to Un-register handset and select Choose the handset to un-register from the list and press Enter the 4-digit RC code and press OK OK Note: should you have your handset serviced alone, please make sure it is unregistered from the base station before taking it back to the repair centre.
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:40 Page 28 Scroll to Set time and select Enter the current time and press OK Warning: If your phone is connected to an ISDN line through an adaptor, the date & time may change after each call. Please check the date & time settings in your ISDN system. Please contact your network provider (see FAQ p.56).
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:40 Page 29 Answer machine Saved messages Record a memo Outgoing messages Answerphone settings The DECT 617 includes an answer machine that records the calls when it is activated.You can reach the answer machine from the base station or the handset. By default, the answer machine is activated. It can store up to 95 messages within the maximum recording time of 40 minutes. A message can be up to 3 minutes long.
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:40 Page 30 To play and browse through saved message(s) via the handset Press to enter the carousel menu Scroll to Answer machine and select Select Saved messages, the message which was recorded first is automatically played Press to access the Options Press to select Play To go to next or previous messages, scroll to Next message or Previous message and select Note: you can listen to the message(s) via the Call log.
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:40 Page 31 Settings To select the answer mode and the outgoing message (OGM) type You can select among 2 answer modes :Answer only (when no messages can be left) and Answer & record (when messages can be left). For each mode, 2 outgoing message types are available: predefined or personal message. By default the answer machine is set to Answer & Record with predefined OGM.
DECT613_GBIE_part1_07_09_04.qxd 07/09/2004 16:40 Page 32 The message is automatically played back.You can delete and/or record it again.The personal message can be up to 1 minutes long Note: Select Standard OGM for answer only mode or Standard OGM for Answ. & Record mode if you have no CLI subscription.
DECT613_GBIE_part2_07_09_04.qxd 07/09/2004 16:51 Page 1 To set the recording quality There are 2 recording qualities: standard and high. In standard quality the total capacity is 40 minutes and in high quality the capacity is around to 20 minutes.
DECT613_GBIE_part2_07_09_04.qxd 07/09/2004 16:51 Page 2 To change the remote control code The default code is the registration code.We advise you to personalize it.
DECT613_GBIE_part2_07_09_04.qxd 07/09/2004 16:51 Page 3 Intercom Call all Handset list Intercom menu is accessible via the carousel or Using the Intercom (if there are at least 2 handsets) This feature allows you to make free internal calls, transfer external calls from one handset to another, use the conference option and the babysit feature (room monitoring).
DECT613_GBIE_part2_07_09_04.qxd 07/09/2004 16:52 Page 4 The called handset rings.The external call is put on hold. If there is no answer from the called handset you can resume the call on the first handset. Take the line on the called handset, both internal callers can talk Press to select Transfer (with handset 1) Scroll to Switch and come back to the external caller Note: to answer the call on the second handset you can press .
DECT613_GBIE_part2_07_09_04.qxd 07/09/2004 Phonebook Add new View 16:52 Page 5 Phonebook menu is accessible via the carousel or 250 names and numbers can be stored in the phonebook. The phonebook contains all the information related to the callers, especially the group settings.The names and numbers are shared with all the handsets registered to your base. Group settings There are 3 groups (group A, group B and group C).When ringing, the ring tone helps you identify the caller’s group (see p.
DECT613_GBIE_part2_07_09_04.
DECT613_GBIE_part2_07_09_04.qxd 07/09/2004 16:52 Page 7 To define a group for a name and number (see Group settings p.
DECT613_GBIE_part2_07_09_04.qxd 07/09/2004 16:52 Page 8 Call log View Delete all Call log settings Call log menu is accessible via the carousel or The call log can store up to 40 entries : unanswered calls : memo or recorded conversation* : messages* sends : outgoing calls : answered calls : messages (operator voice mail/if operator the information) * DECT 617 only The call log shows the list of incoming & outgoing calls.
DECT613_GBIE_part2_07_09_04.
DECT613_GBIE_part2_07_09_04.qxd 07/09/2004 Enter the text and press 16:52 Page 10 OK (see page 19) Press to select Send now Note: Once in the list of names, press to directly edit an SMS Delete all To delete all the call log Press to enter the carousel menu Scroll to Call log and select Scroll to Delete all and select Press to confirm OK Warning: entries with unread messages will also be deleted (DECT 617 only).
DECT613_GBIE_part2_07_09_04.qxd 07/09/2004 16:52 Page 11 Network This feature allows you to activate or deactivate operator services that are subscription dependent. You need to set up codes (see page 55). Contact your network operator for more details.You can usually subscribe to Call forward, operator voice mailbox etc... Example of service: Call forward Calls can be redirected to another phone number. Set the code (see page 55) and activate it when necessary.
DECT613_GBIE_part2_07_09_04.qxd 07/09/2004 16:53 Page 12 Extra Call duration Alarm clock Do Not Disturb mode Call duration Press to enter the carousel menu Scroll to Extra and select Press to select Call duration The total communication time is displayed Press to Reset the counter Alarm clock To activate / deactivate the alarm clock A long press on activates/deactivates the alarm clock with your own settings.
DECT613_GBIE_part2_07_09_04.
DECT613_GBIE_part2_07_09_04.
DECT613_GBIE_part2_07_09_04.qxd 07/09/2004 16:53 Page 15 Group ring tones To set the group ring tones There are 3 groups of callers (see p 39 Group settings).You can associate 1 ring tone to a group.
DECT613_GBIE_part2_07_09_04.qxd My ring tones 07/09/2004 16:53 Page 16 only available in the UK This menu gives access to all available downloaded ring tones.These ring tones can be set on your handset or on your base station (see page 22).You can store up to 3 downloaded ring tones.
DECT613_GBIE_part2_07_09_04.qxd 07/09/2004 16:53 Page 17 Scroll to Record new and select Press to start recording To delete a recorded melody Press to enter the carousel Scroll to Sounds and select Scroll to Record pers. melody and select Scroll to Delele and select Press OK to confirm Settings To set the base loudspeaker volume only available for DECT 617 Press to enter the carousel Scroll to Sounds and select Scroll to Settings and select Press to select Base loudspeaker vol.
DECT613_GBIE_part2_07_09_04.
DECT613_GBIE_part2_07_09_04.qxd 07/09/2004 16:53 Page 19 Base station Enable registration Line settings Service code settings Enable registration This feature allows you to register a DECT peripheral without keypad. Some DECT peripherals, such as repeaters, do not have any keypad. A special menu-operated procedure is used to register such peripherals to the base station.
DECT613_GBIE_part2_07_09_04.qxd 07/09/2004 16:53 Page 20 To change the recall type Press to enter the carousel menu Scroll to Base station and select Scroll to Line settings and select Scroll to Recall type and select Press to select Short flash or scroll to Long flash and select Note: this setting is useful when using operator services.The use of some services accessed with +1, +2 and +3 (call waiting, call forward...
DECT613_GBIE_part2_07_09_04.qxd 07/09/2004 16:53 Page 21 Service code settings When you subscribe to extra services with your operator you may need to set some codes in your phone.The default codes are the codes used by the main national operator. If you subscribed to another operator you may need to change the codes. Contact your network operator for more information on the services.
DECT613_GBIE_part2_07_09_04.qxd 07/09/2004 16:53 Page 22 FAQ 1/ I have no dialling tone after having installed my phone. How do I solve this problem? Check that you have connected your phone using the supplied line cable and not the one from any previous phone (they are often wired differently). Check that you have fully charged the handset according to the instructions given for the phone. Check that the aerial icon (radio link with the base station) is displayed.
DECT613_GBIE_part2_07_09_04.qxd 07/09/2004 16:53 Page 23 8/ What is CNIP (Caller Name Identification)? As with the CLI service this new feature is dependent on the Network and it has to be activated by your Operator (by subscription). It will allow you to have the name of the caller displayed upon an incoming call. This service may not be available from all Operators yet.We advise you to check with your Operator. NB.
DECT613_GBIE_part2_07_09_04.qxd Troubleshooting 07/09/2004 16:53 Page 24 www.philips.
DECT613_GBIE_part2_07_09_04.
DECT613_GBIE_part2_07_09_04.
