DECT122_GBIE_09.qxd 27.09.
DECT122_GBIE_09.qxd 27.09.2005 17:06 Seite 2 Conformity, environment and safety Safety information This equipment is not designed to make emergency calls when the power fails. An alternative has to be made available to allow emergency calls. Conformity Hereby, Philips declares that the DECT 122 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
DECT122_GBIE_09.qxd 27.09.2005 17:06 Seite 3 Declaration of conformity We, PHILIPS Consumer Electronics Route d'Angers 72081 Le Mans Cedex 9 France Declare that the products DECT122xx are in compliance with ANNEX IV of the R&TTEDirective 1999/5/EC and then with the following essential requirements : Article 3.1 a : (protection of the health & the safety of the user) Safety : EN 60950-1 (10/2001) SAR : EN 50361 (2001) Article 3.
DECT122_GBIE_09.qxd 27.09.2005 DECT 122 Handset 17:06 Earpiece Display Icons see page 5 Menu key & Softkey OK - In idle mode, short press to access the main menu. - Short press to select next menu level. - In Edit & Phonebook mode, short press to confirm OK or view selected phonebook record. Hang-up key - A short press to hang-up the line or to exit (return to idle mode). - A long press to power off the handset. - To exit Edit & Phonebook mode.
DECT122_GBIE_09.qxd 27.09.2005 17:06 Seite 5 Icons on the handset display The display gives information about the operation of your telephone. Following icons can be shown in the headline of the display: When being used for the first time, it is sometimes necessary to wait until the battery is sufficiently charged before the icons appear on the display. When ON the battery is fully charged. When blinking, this symbol indicates that the battery needs to be charged. An external call is in progress.
DECT122_GBIE_09.qxd 27.09.2005 17:06 Seite 6 DECT 122 base station Paging key The paging key enables you to locate a missing handset if the handset is in range and has charged batteries. Press the key until the handset starts to ring. Once retrieved, press paging key again to end paging.
DECT122_GBIE_09.qxd 27.09.2005 17:06 Seite 7 Installing the base station Place your product close enough to the telephone and mains power sockets so that the cables will reach.To properly install the base station, plug the line cord and the power cable into the base station. Plug the cord and the cable into the wall.
DECT122_GBIE_09.qxd 27.09.2005 17:06 Seite 8 Installing and replacing the batteries in the handset To insert the batteries, open the battery cover, place the batteries as indicated and then replace the battery cover.When the battery icon is blinking, charge is needed. Allow 12 - 15 hours for the batteries to fully charge. On first use it may be necessary to wait for a few minutes before seeing symbols on the display. Never use any battery type other than the one supplied : risk of explosion.
DECT122_GBIE_09.qxd 27.09.2005 17:06 Seite 9 Menu structure From idle mode, press keys to enter the menu. Use the Navigation to go up or down in the menu list. Press Softkey OK to confirm the selection. Press Softkey BACK to exit the menu or to go back to the previous menu level. PHONEBOOK ADD NUMBER EDIT NUMBER DEL.
DECT122_GBIE_09.qxd 27.09.2005 17:06 Seite 10 Handset power OFF and ON To power the handset OFF or ON long press the key. Text or number entry You can enter the names of your phonebook entries character by character, pressing the corresponding key as many times as necessary to reach the desired character. Press under the label to delete a character.
DECT122_GBIE_09.qxd 27.09.2005 17:06 Seite 11 Using the telephone Keypad lock / unlock Long press the key to lock/unlock the keypad in idle mode. KEYS LOCKED is displayed on the screen. Making a call ✦ Answering a call / Hanging up answer the call. To end the conversation, press key or replace the handset on the base flashes on an incoming call. station. ✦ Calling directly dial the phone number. ✦ Predialling the number before calling Dial the phone number To correct entries use BACK.
DECT122_GBIE_09.qxd 27.09.2005 17:06 Seite 12 Redial list to exit The redial list contains the 5 most recently dialled numbers. SAVED To delete a character use ✦ Accessing / exiting the redial list Press / scroll through the redial list BACK ✦ Calling a number from the redial list Press scroll through the redial list ✦ Saving redial list numbers into the phonebook Press SAVE NUMBER scroll to select ENTER NAME enter name BACK.
DECT122_GBIE_09.qxd 27.09.2005 17:06 Seite 13 Phonebook 30 names and numbers can be stored in the built-in phonebook of the handset.The names are stored in alphabetical order. ✦ Adding a new entry Each entry contains a name (12 characters) and a number (24 digits). Press in idle mode PHONEBOOK press Down 2 times ADD NUM BACK. ENTER NAME ENTER NUMBER enter the name ✦ Changing a phonebook name or number PHONEBOOK press Down 2 times EDIT NUMBER press Down 1 time Press spacing.
DECT122_GBIE_09.qxd 27.09.2005 17:06 Seite 14 ✦ Edit a number when browsing phonebook list Press Down in idle mode EDIT NUMBER press Down 1 time scroll to select ENTER NAME ENTER NUMBER enter new name to confirm. enter new number ✦ Delete an entry when browsing phonebook list Press Down in idle mode DELETE NUM press Down 2 times scroll to select DELETE? to confirm.
DECT122_GBIE_09.qxd 27.09.2005 17:06 Seite 15 Call log This feature is available if you have registered to the caller identification service with your operator. The call log stores the last 20 external calls received : - network message service information* ✦ Accessing / exiting the call log Press Up * Subject to a subscription with your operator.
DECT122_GBIE_09.qxd 27.09.2005 17:06 Seite 16 ✦ Deleting all the Call log entries Press Up DELETE LIST press Down 3 times DELETE? to confirm. Using the Intercom This function can only be used with a multi-handset configuration. It allows you to make free internal calls, transfer external calls from one handset to another and to use the conference option. ✦ Internal call Press or press to call all handsets enter handset no.* Press to answer and to end an internal call.
DECT122_GBIE_09.qxd 27.09.2005 17:06 Seite 17 Paging This feature allows you to locate the handset(s). Press on the base station. Press any key on the handset to stop ringing once relocated. All the subscribed handsets ring. Chain Dialing If you have entered in your phonebook for example only the main number of a company without the extension, this feature allows you to add the subnumber (extension) of a particular person and to dial out this number.
DECT122_GBIE_09.qxd 27.09.2005 17:06 Seite 18 ✦ To set the alarm tone Press CLOCK/ALARM press Down 1 time press Down 2 times ALARM TONE to confirm. *Choose : MELODY 1 or MELODY 2 or MELODY 3 scroll to select* Personal Settings ✦ To set the handset ringer volume or silence mode (Ringer OFF) Press PERSONAL SET press Down 2 times HANDSET TONE RING VOLUME to confirm. scroll to select* The current ring melody is played.
DECT122_GBIE_09.qxd 27.09.2005 17:06 Seite 19 ✦ To rename the handset Press The default name is : PHILIPS. You can enter 10 characters for the handset name. PERSONAL SET press Down 2 times HANDSET NAME press Down 1 time enter the name to confirm. ✦ To activate / deactivate the auto answer mode Press PERSONAL SET press Down 2 times AUTO ANSWER press Down 2 times If ON you take the line by lifting the handset from the charge cradle. scroll to select ON or OFF to confirm.
DECT122_GBIE_09.qxd 27.09.2005 17:06 Seite 20 Advanced Settings ✦ To change the recall time Press ADVANCE SET press Down 3 times RECALL TIME This option is useful when using operator services. to confirm. scroll to select SHORT or LONG ✦ To change the dial mode By default your phone is pre-configured with the appropriate dial mode for your country and you don’t have to change this setting. Press ADVANCE SET press Down 3 times DIAL MODE press Down 1 time select TONE or PULSE to confirm.
DECT122_GBIE_09.qxd 27.09.2005 17:06 Seite 21 ✦ To set or change Call Barring This menu allows you to limit the use of your phone to specific calls by barring parts (prefix) of outgoing numbers.You can set 4 different barring numbers. Press ADVANCE SET press Down 3 times press Down 3 times CALL BARRING enter the PIN code* BARR NUMBER press Down 1 time scroll to select 1/2/3/4 to confirm. enter the barring number** *By default the PIN code is 0000 **The maximums for the barring number is 4 digits.
DECT122_GBIE_09.qxd 27.09.2005 17:06 Seite 22 ✦ To set or change an SOS number The SOS number feature allows you to enter 3 SOS phone numbers, which can be dialed out although the call barring ist activated.The maximum length of an SOS number is 4 digits.The PIN code is required when modify the SOS number. Press ADVANCE SET press Down 3 times press Down 4 times SOS NUMBER enter the PIN code* to confirm.
DECT122_GBIE_09.qxd 27.09.2005 17:06 Seite 23 ✦ To unregister a handset Press ADVANCE SET press Down 3 times *By default the PIN code is 0000 press Down 6 times UNREGISTER enter the PIN code* scroll to select the handset no. UNREGISTERED appears on the screen If you have your handset serviced, please make sure it is unregistered from the base station before taking it back to the repair centre. ✦ To change the PIN code The default PIN code is “0000”.We advise you to personalize it.
DECT122_GBIE_09.qxd Default settings Handset Ringer volume : Handset Ringtone : Handset earpiece volume : Handset key tone : Battery low tone : Menu language (Handset) : Auto answer : Handset name : Time/Date (Handset) : Dialling mode : Flash time : PIN code : Alarm : Alarm tone : Area code : Call barring : SOS number : Redial list : Phonebook memory : Call log : 24 27.09.
DECT122_GBIE_09.qxd 27.09.2005 Troubleshooting No dialling tone No ring tone The icon does not appear The icon is blinking Crackling on the line The handset displays ‘not available’ - when attempting to add another handset to the base station - when using a handset Seite 25 www.philips.
