Always there to help you Register your product and get support at www.philips.
1 Important 2 2 2 Your car audio system 3 3 3 4 3 Install the car audio system 6 6 8 Safety Introduction What's in the box Overview of the system Connect wires Mount into the dashboard 4 Get started Power on Change system settings Set the clock Select a source 5 Listen to radio Select a radio region Select a tuner sensitivity Tune to a radio station Store radio stations in memory Tune to a preset station Play with RDS 6 Use Bluetooth devices Pair a device Play audio from a connected device Mak
1 Important Safety Read and understand all instructions before you use the device. If damage is caused by failure to follow instructions, the warranty does not apply. • Modification of the product could result in hazardous radiation of EMC or other unsafe operation. • The device is designed for negative ground (earth) 12 V DC operation only. • To reduce the risk of traffic accidents, do not pick up or make a phone call, nor watch video when driving.
2 Your car audio system Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. Introduction With this system, you can: • enjoy audio from USB storage devices, Android-powered mobile phones, and other external devices, • listen to radio stations, • charge your Android-powered mobile phone, and • make phone calls.
Overview of the system u t sr q p on a b c d ef jk ghi a b c • • e • • • Tune to a radio station. Press to skip to the previous track. Press and hold to rewind a track. • Press to enable or disable the full sound. Press and hold to access the sound setting menu. • • Press repeatedly to select a source. Press and hold to activate the selection of listening zones. • In radio mode, press to select the preset radio station of No. 1.
• • • j • • k • • • In radio mode, press to select the preset radio station of No. 4. In radio mode, press and hold to store the current radio station at channel No. 4. For tracks, press to start playing all tracks in the current album or folder randomly. In radio mode, press to select the preset radio station of No. 5. In radio mode, press and hold to store the current radio station at channel No. 5. In radio mode, press to select the preset radio station of No. 6.
3 Install the car audio system Connect wires Note Caution • Use the controls only as stated in this user manual. Always follow the instructions in this chapter in sequence. These instructions are for a typical installation. However, if your car has different requirements, make the adjustment accordingly. If you have any question regarding installation kits, consult your local retailer. Note • This system is designed for negative ground (earth) 12V DC operation only.
5 6 7 8 Connects to Red wire The +12V power terminal which is live in the accessory (ACC) position of the ignition switch. If there is no accessory position, connect to the +12V car battery terminal that is always live. Make sure that the black ground (earth) lead is connected to a metal surface of the car first.
Mount into the dashboard 3 Place the supplied rubber cushion over the end of the mounting bolt. Note • If your car has no an on-board drive or navigation • • 1 computer, disconnect the negative terminal of the car battery. If your car has an on-board drive or navigation computer, the computer may lose its memory when you disconnect the car battery. If the car battery is not disconnected, to avoid shortcircuit, make sure that bare wires do not touch each other.
4 Get started 1 2 Power on Press . » [WELCOME] scrolls. • To power off the system, press and hold until [GOODBYE] is displayed. Change system settings 1 2 3 Press and hold menu. to access the system Press repeatedly to select an option. • [BT RECON]/[DISCONNECTED] • [RDS] • [PTY >] • [RDS AF] • [RDS TA] • [TP STORE] • [RDS REG] • [RDS CT] • [STORE >] • [AREA] • [LOCAL] • [CLOCK] • [CLOCK 12H] • [BEEP] • [BKO] • [DIMMER] • [DEMO] Rotate • to select a setting. To exit the setting, press .
• [USB]: When a USB storage device is connected and recognized, you can select this source to play audio files that are stored on it. 5 Listen to radio Select a radio region You can select a radio region that matches your location. 1 2 3 Press and hold menu. to access the system Press repeatedly until [AREA] is displayed. Rotate to select an option.
1 2 3 4 Press repeatedly to switch the source to [RADIO]. Press repeatedly to select a band: [FM1], [FM2], [FM3], [MW1], or [MW2]. Press and hold or frequency digits blink. until the Press or repeatedly to tune to a radio station manually. » The radio station is broadcast. • To search for a radio station automatically, press or . Store radio stations in memory Repeat steps 2 and 3 to store more radio stations. • To replace a radio station, store another one in its channel.
3 4 Press Rotate then press Item Program type 1 2 NEWS AFFAIRS 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 12 to confirm. to select a program type, and to confirm.
• When a traffic announcement cuts in, you can press to switch the system to the previous mode. Receive traffic programs only If you want to receive traffic announcements only, use the TP (Traffic Program) function. 1 2 3 Press and hold menu. to access the system Press repeatedly until [TP STORE] is displayed. Press to start searching for and storing stations that regularly broadcast traffic announcements. » After the search is complete, the first stored station starts broadcasting.
Tip Note • You can also disable the Bluetooth function on this connected device. profile, control play on the connected device. Reconnect a device 1 2 3 Press and hold displayed. • If the connected device does not support the AVRCP until [BT RECON] is Press to confirm. • If the auto connection between CMD305A and this device is authorized, CMD305A reconnects to this device automatically. If not, perform step 3. On this device, accept the connection request from CMD305A. » [CONNECTED] scrolls.
By default, voice comes from the loudspeakers during a call. 1 2 Press and hold until [TRANSFER] is displayed. » The loudspeakers are muted, and the voice comes from your mobile phone only. Take up your mobile phone for the conversation. 7 Play from a USB storage device This system can play .mp3 and .wma files that are copied onto a compatible USB storage device. Note • Philips does not guarantee compatibility with all USB storage devices.
Control play During play, follow the instructions below to control play. Buttons Functions Pause or resume play. / / 16 EN Skip to the previous or next track. Press and hold to rewind a track or search forward fast within a track. Skip to the previous or next folder when one or more folders exist. Select a repeat mode. • [REPEAT TRACK]: repeat the current track • [REPEAT ALL]: repeat all tracks • [REPEAT FOLDER]: repeat all tracks in the current folder Enable or disable shuffle play.
2 An application Philips CarStudio is available on Google Play Store for this car audio system. To enjoy full features, download and install the application to your Android-powered phone. Pull out the dock bracket until you see the yellow lines and hear a "click". K CLIC Compatible with Android™ Before using the dock, check your Androidpowered phone and make sure that it meets the following requirements: • With Android operating system V2.
Connect your phone 3 You can connect your phone to the dock directly or though the supplied USB cable. Connect your phone to the dock with its screen facing you. • To match the USB socket of your phone, turn the USB connector by 180° as illustrated if necessary. Dock your phone Note • Make sure that the width of your phone is between 52 mm and 73 mm. • Before docking your phone, make sure that the dock bracket is in portrait position. 1 Flip out the USB connector or hide it in the dock.
Adjust the viewing angle. English 2 Connect the USB cable between • the USB socket of your phone, and • the USB socket in the dock. Switch to portrait mode 1 Adjust the dock bracket Turn the dock bracket clockwise by 90 degrees. Caution • When the dock bracket is in portrait position, do not turn it clockwise. • When the dock bracket is in landscape position, do not turn it anti-clockwise. Switch to landscape mode 1 2 Adjust the viewing angle. Turn the dock bracket anti-clockwise by 90 degrees.
Install the CarStudio application 2 Tap 3 Type in CarStudio and then tap Search. to display the search interface. Note • Make sure that the internet connection is active on your phone. 1 Run the Google Play Store application on your phone.
5 Tap Philips CarStudio in the search result list. 1 Tap the icon of CarStudio application to run it on your phone. » The main interface is displayed. English 4 Tap Install and then Accept & download to start the download and installation. » After the download and installation is complete, the CarStudio icon is displayed in the list of applications.
• (external audio input): Switch the source to the audio input that is transferred through the AUDIO-IN socket. • (USB): Switch the source to USB storage device. • (settings): Change settings • : Return to the main interface • : Add a shortcut of an application onto the current interface. Tap to display the dialog box, tap Application on the dialog box to display all applications that are installed on your phone, and then tap an application name to create a shortcut.
Push the dock panel inwards until you hear a "click". 10 Adjust sound English 2 The following operations are applicable to all compatible media. CLICK 3 Adjust the volume level Rotate clockwise or anti-clockwise. Flip up the cover. Mute sound Press . • To restore sound, press again. Use the DBB sound effect Press and hold until one of the following settings is displayed. • [DBB ON]: Dynamic bass boost (DBB) is enabled. • [DBB OFF]: DBB is disabled.
Enable the full-range sound Press repeatedly to select one of the following settings. • [FULL ON]: Enable the full-range sound • [FULL OFF]: Use the preset equalizer that you select Select a preset sound equalizer 1 2 Press and hold until [EQ] and the name of current equalizer are displayed. Rotate to select one of the preset sound equalizers.
4 Insert a new fuse with the same specifications (15 A). English 12 Additional information SUB-W L R REAR LINE OUT Reset the system You can reset the system to factory default settings. Note 1 2 • If the fuse gets damaged immediately after it is replaced, Open the protective cover for the USB socket, MP3-LINK socket, and RESET button. an internal malfunction may occur. In this case, consult your Philips retailer. Press RESET with the tip of a ball-point pen or toothpick. » The system is reset.
13 Product information Note • Product information is subject to change without prior notice. General Power supply Fuse Suitable speaker impedance Maximum power output Continuous power output Pre-Amp output voltage Aux-in level Dimensions (W x H x D) Weight 12 V DC (11V - 16V), negative ground 15 A 4-8 50 W x 4 channels 22 W x 4 RMS (4 10% T.H.D.) 2.5 V 500 mV 188 x 58 x 199.5 mm 1.
Warning • Never remove the casing of this product. To keep the warranty valid, never try to repair the product yourself. If you encounter problems when using this product, check the following points before requesting service. If the problem remains unsolved, go to the Philips Web page (www. philips.com/support). When you contact Philips, make sure that the product is nearby and the model number and serial number are available.
• For some mobile phones, the Bluetooth connection may be deactivated automatically as a power-saving feature. This does not indicate any malfunction of the system. 15 Notice Any changes or modifications made to this device that are not expressly approved by Philips Consumer Lifestyle may void the user’s authority to operate the equipment. Compliance 1177 This product complies with the radio interference requirements of the European Community.
English Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.
Specifications are subject to change without notice © 2012 Koninklijke Philips Electronics N.V. All rights reserved. CMD305A_12_UM_V1.
