Color TV with built-in VCR Owner’s Manual CCC134AT CCC194AT Read this manual first! Congratulations on purchasing this Philips product. We’ve included everything you need to get started. If you have any problems, Philips Representatives can help you get the most from your new product by explaining: • Hookups, • First Time Setup, and • Feature Operation. Do not attempt to return this product to the store.
Return your Warranty Registration card today to ensure you receive all the benefits you’re entitled to. Once your PHILIPS purchase is registered, you’re eligible to receive all the privileges of owning a PHILIPS product. So complete and return the Warranty Registration Card enclosed with your purchase at once. And take advantage of these important benefits.
Introduction 3 Welcome to your TV/VCR owner’s manual. This manual describes two models: CCC134 and CCC194. The models may look different, but they operate exactly the same. The CCC134 is illustrated in this manual. The features in this manual apply to both models.
Table of Contents Setting Up Your TV/VCR Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Before Using the TV/VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Hooking Up the TV/VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before Using the TV/VCR 5 Putting Batteries in the Remote Control 1 1 2 Remove the battery compartment lid on the bottom of the remote control by pressing in the tab, then pulling up the lid. Place two AA batteries inside the battery compartment with their + and – ends aligned as indicated. 2 3 Replace the battery compartment lid.
Hooking Up the TV/VCR 1 Hook up your TV/VCR using one of the connections shown. A. Hooking Up Your TV/VCR With a Cable Signal or Outdoor Antenna Connect a Cable signal or an antenna to the ANT(enna) Jack. ANT. ANT. B. Hooking Up Your TV/VCR With a Cable Box To view any channel, set the TV/VCR to the Cable Box output channel (channel 03 or 04). Then, select channels at the Cable Box. Connect the Cable signal to the IN Jack on the Cable Box.
Hooking Up the TV/VCR (cont’d) 7 D. Hooking Up Your TV/VCR to Another Video Source (VCR, DVD Player, Camcorder, etc.) You may need this connection if you want to copy tapes or view tapes or discs that you are playing on the VCR, DVD Player, or camcorder. Select channel 00 (A/V IN) at the TV/VCR when viewing tapes or discs that are playing on the VCR, DVD Player, or camcorder. Details are on page 32.
Turning On the TV/VCR Before you turn on the TV/VCR, make sure batteries are in the remote control and you have connected the TV/VCR correctly. The instructions on this page work only when you turn on the TV/VCR for the first time. 1 Press the COMBI button, then press the POWER button. The TV/VCR will come on and the screen shown below will appear. SELECT LANGUAGE > ENGLISH EJECT POWER 3 5 STATUS /EXIT MENU 1 CLEAR FM 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP ALT.
Language Selection 9 Follow the steps below to change the language of the on-screen displays and menus. 5 2-4 1 Press the COMBI button, then press the MENU button. PRESS B > PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS EJECT POWER 1 STATUS /EXIT MENU CLEAR FM 1 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP ALT.CH 0 2 REC /OTR Press the PLAY/▲ button or the STOP/▼ button to select PRIM. SETUP. Then, press the F.FWD/B button. PRIMARY SETUP REW F.FWD STOP CH. VOL.
Automatic Channel Setup Although the TV/VCR may automatically memorize the channels you receive when you turn it on for the first time, you may set up channels again by following the steps below. 1 2-3 EJECT POWER Press the COMBI button, then press the MENU button. > PRIM. SETUP 1 PRESS B VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS STATUS /EXIT MENU CLEAR FM 1 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP ALT.CH 0 REC /OTR 2 PAUSE /STILL PLAY REW F.
Automatic Channel Setup (cont’d) 11 Adding/Deleting Channels If your channel lineup changes, you may want to add newly available channels or remove channels that are no longer available in your area. You can use the CH(annel) o/p buttons to scroll through only the available channels. To add or delete channels from the TV/VCR’s memory, follow these steps. 1 5 EJECT POWER 1 Press the COMBI button, then press the MENU button. STATUS /EXIT MENU CLEAR FM 1 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP ALT.
Setting the Clock There are three ways to set the clock: Manually, with Automatic PBS Channel Selection, or with Manual PBS Channel Selection. With manual clock setting, you tell the TV/VCR the current time. With Automatic or Manual PBS Channel Selection, the TV/VCR gets the time from your local PBS station. If you use either Manual PBS Channel Selection or Automatic PBS Channel Selection, follow the steps on page 19 to have the TV/VCR maintain the clock according to your Time Zone.
Setting the Clock (cont’d) 13 4 7 5-6 Press the PLAY/▲ button or the STOP/▼ button to select SET MANUAL CLOCK, then press the F.FWD/B button. SET MANUAL CLOCK TIME – – : – – EJECT POWER STATUS /EXIT MENU CLEAR FM DATE – – / – – / – – – – TO END PRESS EXIT 1 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP 5 ALT.CH 0 REC /OTR Press two Number buttons for the hour(s) and two Number buttons for the minute(s). Then press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.
Setting the Clock (cont’d) Automatic PBS Channel Selection 4 2-4 1 Press the COMBI button, then press the MENU button. EJECT POWER > PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS PRESS B 1 STATUS /EXIT MENU CLEAR FM 1 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP 2 ALT.CH 0 REC /OTR Press the PLAY/▲ button or the STOP/▼ button to select PRIM. SETUP. Then, press the F.FWD/B button. PAUSE /STILL PLAY REW F.FWD STOP PRIMARY SETUP CH.
Setting the Clock (cont’d) 15 5 Press the PLAY/▲ button or the STOP/▼ button to select SET PBS CH. AUTO. Then, press the F.FWD/B button. 6 Wait for the TV/VCR to find the time. SET AUTO CLOCK TIME ––:–– DATE ––/––/–––– NOW SEARCHING 7 TO END PRESS EXIT EJECT POWER 6 7 STATUS /EXIT MENU NOW SEARCHING flashes on the TV/VCR screen. 1 CLEAR FM 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP ALT.CH 0 When the TV/VCR finds the PBS channel, the time will appear on the screen.
Setting the Clock (cont’d) Manual PBS Channel Selection 4 2-4 1 Press the COMBI button, then press the MENU button. EJECT POWER > PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS PRESS B 1 STATUS /EXIT MENU CLEAR FM 1 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP 2 ALT.CH 0 REC /OTR Press the PLAY/▲ button or the STOP/▼ button to select PRIM. SETUP. Then, press the F.FWD/B button. PAUSE /STILL PLAY REW F.FWD STOP PRIMARY SETUP CH. VOL.
Setting the Clock (cont’d) 17 5 Press the PLAY/▲ button or the STOP/▼ button to select SET PBS CH. MANUAL. Then, press the F.FWD/B button. 7 Wait for the TV/VCR to find the time. 8 AUTO CLOCK (PBS) CH 02 TIME ––:–– DATE ––/––/–––– SELECT CHANNEL NUMBER TO END PRESS EXIT EJECT POWER STATUS /EXIT MENU 6 Use the Number buttons to select your PBS station. AUTO CLOCK (PBS) CH 12 6 1 CLEAR FM 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP ALT.
Daylight-Savings Time When the Daylight-Savings Time feature is ON, the TV/VCR clock will automatically move forward one hour on the first Sunday in April and move back one hour on the last Sunday in October. To turn Daylight-Savings Time ON or OFF, follow the steps below. 1 5 2-4 EJECT POWER Press the COMBI button, then press the MENU button. > PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS PRESS B 1 STATUS /EXIT MENU CLEAR FM 1 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP ALT.
Time Zone 19 When you set the clock using AUTO CLOCK, specify your time zone. The TV/VCR will maintain the clock according to your time zone. 6 2-5 1 Press the COMBI button, then press the MENU button. EJECT POWER > PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS PRESS B 2 1 STATUS /EXIT MENU CLEAR FM 1 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP ALT.CH 0 REC /OTR Press the PLAY/▲ button or the STOP/▼ button to select PRIM. SETUP. Then, press the F.FWD/B button.
Setting the Remote to Operate a Cable Box/DBS Your TV/VCR remote control may operate your Cable Box/DBS. If the remote control doesn’t operate your Cable Box/DBS now, follow the steps below to program your remote control. 1 2 1 Find your code. Turn on your Cable Box/DBS. Point the remote control at your Cable Box/DBS and press the CABLE/DBS button. Then, press the POWER button. If your Cable Box/DBS turns off, try the other Cable Box/DBS buttons (see pages 24-25 for details).
Setting the Remote to Operate a Cable Box/DBS (cont’d) 21 5 Within 30 seconds, press the Number buttons to enter the two-digit code for your Cable Box/DBS. For example, if you have a Zenith Cable Box, press Number buttons 0, 7. 6 Repeat step 1. If the remote control works your Cable Box/DBS, you’re finished. If the remote control still doesn’t work your Cable Box/DBS, repeat steps 2-5, using a different code for your brand, if available.
Front Panel Cassette Compartment Insert a video cassette tape here. F.FWD Button (Fast Forward) When tape playback is stopped, press to fast forward the tape at high speed. During playback, press to fast forward the tape while the picture stays on the screen. Press to change a setting of a menu item (for example, to adjust the BRIGHTNESS) or to advance to the next menu. PLAY Button Press to play a tape. Details are on page 29. Press to release Slow, Search or Still mode and return to normal playback.
Rear Panel 23 CCC134 ANT. ANT(enna) Jack Connect your antenna or cable here. Details are on page six. AC Power Cord Connect to a standard AC outlet to supply power to the TV/VCR. Antenna Hole Connect the stem of an indoor antenna here. Details are on page six.
Remote Control Buttons POWER Button Press to turn on or off the TV/VCR, Cable Box, or Direct Broadcast System. (You must first press the COMBI or CABLE/DBS button.) Details are on pages five and 20-21. EJECT Button Press to eject the tape. MENU Button Press to display the main menu. You also may use the buttons on the front panel of the TV/VCR to access the main menu. Details are on page 22. Number Buttons Use to select channels and to program TV/VCR functions (such as setting the clock).
Remote Control Buttons (cont’d) 25 FM Button Press to select FM radio mode. Press again to return to TV mode. Details are on page 59. CLEAR Button Press to erase incorrect data when programming TV/VCR functions. Also, press to reset the real-time counter to 0:00:00. Details are on page 42. STATUS/EXIT Button Press to access or remove the status display. Details are on page 28. Press to remove the menu. REC(ord)/OTR Button Press once to start a recording. Details are on page 30.
Adjusting the Picture Controls Follow these steps to adjust the TV/VCR’s brightness, picture, color, tint, and sharpness. 4 2,3 1 Press the COMBI button, then press the MENU button. K > BRIGHTNESS PICTURE COLOR TINT SHARPNESS CHANNEL K TO ADJUST PRESS { / B EJECT POWER 1 STATUS /EXIT MENU CLEAR FM 1 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP ALT.CH 0 2 3 REC /OTR REW F.FWD Press the PLAY/▲ button or the STOP/▼ button to select the desired control (BRIGHTNESS, for example).
Adjusting the Picture Controls (cont’d) 27 Decrease decreased brightness decreased contrast paler more purple softer BRIGHTNESS PICTURE COLOR TINT SHARPNESS Increase increased brightness increased contrast more brilliant more green clearer Press the REW(ind)/{ button to decrease a picture control. Press the F.FWD/B button to increase a picture control. AUDIO STOP EJECT VIDEO REW PLAY F.
On-Screen Status Displays A status display will appear when you press the STATUS/EXIT button or certain function buttons. The contents of the status display will vary. To choose the status display mode, follow the steps below. If you select STATUS ON, then select COUNTER ONLY OFF: ● Whenever you press the STOP/p button or the PLAY/o button, the status display will appear for five seconds. Portions of the status display also may appear when you press other function buttons.
Playing 29 Follow the steps below to play a tape. 1 Insert a tape in the TV/VCR. The power will come on. If the tape’s record tab is missing, playback should start automatically. 1 5 2 If playback does not start automatically, press the COMBI button, then press the PLAY/▲ button to start playback. 3 4 5 Press the STOP/▼ button to stop playback. 4 3 Insert a tape in the TV/VCR. EJECT POWER STATUS /EXIT MENU CLEAR FM 1 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP ALT.
Recording Read and follow the steps below to record a TV program. 1 1 Press the COMBI button, then place a tape with its record tab intact (see page five) in the TV/VCR. The power will come on. Or, if the tape is already in the TV/VCR, press the POWER button to turn on the TV/VCR, if necessary. 2 Press the SPEED button until the desired tape speed appears on the TV/VCR screen. See tape speed details below. EJECT POWER 3 FM 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP ALT.
One-Touch Recording 31 A One-Touch Recording (OTR) is an immediate timed recording from 30 minutes to eight hours long. Before you begin, make sure: ● Channels are set. Details are on page 10. ● There is a tape in the TV/VCR. The record tab must be intact. 4 1 Press the STOP/EJECT button on the TV/VCR to stop the OTR. EJECT POWER p Press the COMBI button, then use the CH(annel) o/p buttons or the Number buttons to select the channel you want to record.
Rerecording (Tape Duplication) AUDIO and VIDEO OUT Jacks on source unit (VCR, DVD Player, or Camcorder) AUDIO VIDEO STOP EJECT REW EARPHONE VIDEO AUDIO OUT Audio Cable from AUDIO OUT to AUDIO In Video Cable from VIDEO OUT to VIDEO In AUDIO and VIDEO In Jacks on TV/VCR 1 Make the connections shown above, using audio and video cables (not supplied). Make sure the source unit (VCR, DVD Player, camcorder, etc.) is connected to a power source. 2 The source unit will play your tape.
Defeat Recording 33 Follow the steps below to prevent accidental recording. 4 2-3 1 Press the COMBI button, then press the MENU button. > PRIM. SETUP PRESS B VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS EJECT POWER 1 STATUS /EXIT MENU CLEAR FM 1 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP ALT.CH 0 2 REC /OTR PAUSE /STILL PLAY REW F.FWD Press the PLAY/▲ button or the STOP/▼ button to select VCR SETUP, then press the F.FWD/B button. STOP CH. VOL.
Timer Recording Follow the steps below to program the TV/VCR to record TV programs while you’re away from home. The TV/VCR will turn itself on, record, and turn itself off automatically. Before you begin, make sure: ● The clock is set. If not, CLOCK MUST BE SET appears, followed by the SET CLOCK menu. Details are on pages 12-17. ● Channels are set. Details are on page 10. ● A tape is in the TV/VCR. Make sure the tape’s record tab is intact and the tape is long enough to record the program.
Timer Recording (cont’d) 35 4 Use the Number buttons (1-8) to select a position in which to store the timer recording. Flashing numbers indicate an open position (one in which a timer recording has not been stored yet). NOTE: If you select a number that already has been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear on the screen for a few seconds. Then information about the program in that position will appear on the screen. If this happens, press the STATUS/EXIT button.
Timer Recording (cont’d) 8 Press the Number 1 button to record in SP speed or press the Number 2 button to record in SLP speed. Details about tape speed are on page 30. You cannot use the SPEED button at this time. ONE TIME PROGRAM PROGRAM 1 CHANNEL 10 TIME ON 09:30 PM TIME OFF 11:00 PM REC SPEED SLP SP=1 SLP=2 11 10 8 EJECT POWER CLEAR FM 1 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP 9 ALT.CH 0 REC /OTR TO CORRECT PRESS CLEAR TO END PRESS EXIT 9 STATUS /EXIT MENU PAUSE /STILL PLAY REW F.
Timer Recording (cont’d) 37 Checking or Clearing Timer Recordings 5 2-4 1 With the TV/VCR on, press the COMBI button, then press the MENU button. 2 3 Press the PLAY/▲ button or the STOP/▼ button to select VCR PROGRAM, then press the F.FWD/B button. Press the PLAY/▲ button or the STOP/▼ button to select PROGRAM REVIEW, then press the F.FWD/B button. The timer recording information for the program in the lowest numbered position will appear on the screen.
Setting Up the VCR Plus+ Programming System 1 First, fill in the boxes on this page. It will only take a few minutes, and you must do it if you want the VCR Plus+ programming system to work properly. Since the channel numbers of the stations you receive may not be the same as the station numbers, and since channel numbers differ from area to area, you must program the TV/VCR with your local channel information.
Setting Up the VCR Plus+ Programming System (cont’d) 39 2 Now, compare the channel numbers you have written in the VCR PLUS+ CH. and CABLE/TV CH. columns. You’ll notice that some stations have VCR Plus+ and Cable/TV channel numbers that are the same, and other stations have channel numbers that do not match. Where the channel numbers DO NOT match, you must tell the TV/VCR the VCR Plus+ and Cable/TV channel numbers according to the following steps. ● Make each entry within 60 seconds of the previous entry.
Timer Recording With the VCR Plus+ Programming System Follow the steps below to program a timer recording using the PlusCode programming numbers in your TV guide. Before you begin, make sure: ● The clock is set. If not, CLOCK MUST BE SET appears. ● Channels are programmed. ● There is a tape in the TV/VCR. Make sure the tape’s record tab is intact and the tape is long enough to record the program. ● You have completed the steps on pages 38-39.
Timer Recording With the VCR Plus+ Programming System (cont’d) 41 4 Press the Number 1 button to record in SP speed or the Number 2 button to record in SLP speed. Your selection will appear to the right of REC SPEED on the screen, although SP=1 SLP=2 will continue to flash. For details about tape speed, see pages 30 and 64. You cannot use the SPEED button at this time.
Real-Time Counter Memory Follow the steps below to reset the real-time counter to zero at a tape location you want to refer to later. 2 1 Press the COMBI button. Then, play, fast forward, or rewind a tape to the location that you would like to refer to later. Stop the tape. EJECT POWER 2 Press the STATUS/EXIT button. The real-time counter will appear on the screen. 01:08 PM CH10 STATUS /EXIT MENU CLEAR FM 1 2 3 4 5 6 7 8 3 9 SLEEP/ WAKE UP ALT.
Repeat Play 43 Follow the steps below to program the TV/VCR to play a tape over and over. 1 4 2-3 EJECT POWER Press the COMBI button, then press the MENU button. > PRIM. SETUP PRESS B VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS 1 STATUS /EXIT MENU CLEAR 1 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP ALT.CH 0 REC /OTR 2 PAUSE /STILL PLAY REW Press the PLAY/▲ button or the STOP/▼ button to select VCR SETUP, then press the F.FWD/B button. FM F.FWD STOP CH. VOL.
A-B Repeat Play Follow the steps below to program the TV/VCR to play the material between two specified points (A and B) on a tape over and over again. 1 Insert a tape in the TV/VCR. 3-5 1 2 Insert a tape in the TV/VCR. EJECT POWER Press the COMBI button, then press the MENU button. > PRIM. SETUP PRESS B VCR PROGRAM VCR SETUP CAPTION REMINDER BRIGHTNESS 2 STATUS /EXIT MENU CLEAR FM 1 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP ALT.CH 0 REC /OTR REW 3 PAUSE /STILL PLAY F.
A-B Repeat Play (cont’d) 45 6 Press the STATUS/EXIT button to remove the menu. AB REPEAT will appear on the screen. Beneath it, the letter A will flash beside the real-time counter. 6 EJECT POWER STATUS /EXIT MENU A A-B REPEAT 0:12:34 CLEAR FM 1 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP ALT.CH 0 7 REC /OTR Play, fast forward, or rewind the tape to the position at which you want to begin playback. Stop the tape, then press the MEMORY button to set the start position (A).
Playback Options Forward and Reverse Searching (SP/LP/SLP) 1 During tape playback, press and release the F.FWD/B button or the REW(ind)/{ button. A fast forward or reverse picture search will begin. EJECT POWER STATUS /EXIT MENU 2 To return to normal playback, press the PLAY/▲ button. CLEAR FM 1 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP ALT.CH 0 Super High Speed Searching (LP/SLP) REC /OTR 1 During tape playback, press the F.FWD/B button or the REW(ind)/{ button, then press again.
Blue Background 47 If you want the TV screen to be solid blue when a weak signal is received, set BLUE BACKGROUND to ON. The screen will be blue and the sound will be muted. Or, if you want to receive the weak signal, set BLUE BACKGROUND to OFF. When you select a channel that is receiving a weak signal, you will see and hear the static in the TV programming. To set BLUE BACKGROUND to ON or OFF, follow the steps below. 1 Press the COMBI button, then press the MENU button.
SmartLock SmartLock enables parents to prevent their children from watching inappropriate material on TV. SmartLock reads the ratings for programming (except for news and sports programs, unedited movies on premium cable channels, and Emergency Broadcast System signals), then denies access to programming if the program’s rating meets or exceeds the limitations you select. The ratings are defined on page 51. To block ratings, follow the steps below.
SmartLock (cont’d) 49 5 5-6 Press the PLAY/▲ button or the STOP/▼ button to select Movie Ratings or Parental Guidelines. Then, press the F.FWD/B button. EJECT POWER BLOCK 7 > Movie Ratings Parental Guidelines SELECT KL CHOOSE B TO END PRESS EXIT STATUS /EXIT MENU CLEAR FM 1 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP 6 ALT.CH 0 REC /OTR Press the PLAY/▲ button or the STOP/▼ button to select the rating you want to block. Then, press the F.FWD/B button so that ON appears beside the rating.
SmartLock (cont’d) 6 3,5 To change the access code, follow these steps. 1 Press the COMBI button, then press the MENU button. EJECT POWER > SMARTLOCK REVIEW EXIT PRIM. SETUP VCR PROGRAM VCR SETUP PRESS B 2 1 STATUS /EXIT MENU CLEAR FM 1 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP ALT.CH 0 REC /OTR Press the PLAY/▲ button or the STOP/▼ button to select SMARTLOCK. Then, press the F.FWD/B button. REW F.FWD SMARTLOCK _ _ _ _ PAUSE /STILL PLAY STOP CH. VOL.
SmartLock (cont’d) 51 To check the SmartLock settings and see which ratings you have blocked, follow these steps. 3 1 Press the COMBI button, then press the MENU button. > REVIEW PRESS B EXIT PRIM. SETUP VCR PROGRAM VCR SETUP CAPTION EJECT POWER 1 STATUS /EXIT MENU CLEAR FM 1 2 3 4 5 6 7 8 9 SLEEP/ WAKE UP 2 REC /OTR Press the PLAY/▲ button or the STOP/▼ button to select REVIEW. Then, press the F.FWD/B button so that the SmartLock settings appear.
Sleep Timer Use the sleep timer to program the TV/VCR to shut off in a certain amount of time. 3 1 Press the COMBI button, then press the SLEEP/WAKE UP button. EJECT POWER STATUS /EXIT MENU CLEAR FM TO ADJUST PRESS { / B 1 2 3 4 5 6 7 8 –TIMER– > SLEEP OFF WAKE UP ON-TIME 1 2 ALT.CH 0 REC /OTR TO ADJUST PRESS { / B 30 MIN WAKE UP ON-TIME 2 F.FWD STOP CH. VOL. MUTE CABLE /DBS SMART PICTURE COMBI SPEED MEMORY VCR PLUS+ F.
Wake Up Timer 53 The Wake Up Timer turns on the TV/VCR automatically at a specified time within the next 24 hours. You may set the TV/VCR to turn on at a TV channel (the channel at which the TV/VCR was set last) or with VCR playback. To set the Wake Up Timer, follow the steps below. Before you begin: ● Set the clock. If the clock is not set, CLOCK MUST BE SET will appear on the screen at step 2. Then the SET CLOCK menu will appear. Details are on pages 12-17.
Closed Caption When you watch a program that has closed captions, you can access on-screen boxes containing the program’s dialogue (for example, what a character is saying), dialogue in a foreign language, or information (such as a channel guide, schedule, or announcements). Follow the steps below to select closed captions. Not all TV programs and commercials have closed captions. Similarly, all types of closed captions (second language, half-screen text, etc.) are not always broadcast.
Closed Caption (cont’d) 55 4 Press the STATUS/EXIT button. The type of closed captions you selected at step 3 will appear on the screen if available. EJECT POWER STATUS /EXIT MENU CLEAR FM 1 2 3 4 5 6 7 8 4 9 SLEEP/ WAKE UP ALT.CH 0 REC /OTR PAUSE /STILL PLAY REW F.FWD HELLO STOP Standard Closed Captions CH. VOL. MUTE CABLE /DBS SMART PICTURE COMBI SPEED MEMORY VCR PLUS+ F.
Volume Bar Volume Bar Usually, the volume bar appears when you press the VOL(ume) o//p buttons. If you do not need it, set the VOLUME BAR to OFF. For example, when you watch a program that is being broadcast with closed captions, you may choose to set the VOLUME BAR to OFF so the captions can remain on the screen. The captions will remain on the screen even when you press the VOL(ume) o//p buttons or the MUTE button. 1 Press the COMBI button, then press the MENU button.
Automatic Operation Features 57 The following playback features will always operate. Automatic Playback When you put a tape in the TV/VCR, the power will come on automatically. If the tape’s record tab is missing, playback will begin. If a timer recording is set, the power will not come on automatically when you insert a tape with the record tab intact. If a timer recording is set and the TV/VCR power is off, the TV/VCR will eject the tape if the record tab is missing.
SmartPicture The SmartPicture feature allows you to improve the TV/VCR’s picture when viewing sports, a movie, or video games; to improve the picture when the antenna/cable signal is weak; or to reset the picture controls to their original settings. 1 EJECT POWER STATUS /EXIT MENU 1 Press the COMBI button, then press the SMART PICTURE button repeatedly until the SmartPicture mode you want appears on the screen. Your selection will remain on the screen for about 10 seconds, then disappear.
FM Radio 59 Follow the steps below to listen to FM radio stations through the TV/VCR. Choosing FM stations... 1 EJECT POWER Press the COMBI button, then press the FM button to select FM mode. The radio frequency appears on the TV/VCR screen, moving around the screen every few seconds. STATUS /EXIT MENU 1 FM 88.0MHz CLEAR FM 2 3 4 5 6 7 8 1,3 9 SLEEP/ WAKE UP ALT.CH 0 REC /OTR 2 Press the CH(annel) o//p buttons until your desired radio frequency appears.
Reminder The channel number will remain on the screen at all times when you set REMINDER to ON. The exception is when closed captioning is selected or during tape playback. Set REMINDER to ON or OFF by following the steps below. 4 2-3 EJECT POWER 1 1 Press the COMBI button, then press the MENU button. CLEAR 1 2 3 4 5 6 7 8 OFF REC /OTR PAUSE /STILL PLAY REW F.FWD STOP 2 CH. VOL. MUTE CABLE /DBS Press the PLAY/▲ button or the STOP/▼ button to select REMINDER.
Index Search 61 This feature allows you to index the starting points of programs that you have recorded on a tape. Then, you can easily rewind or fast forward to that point. Example: If you are watching program number 4 and you want to fast forward to program number 7, skip three programs. EJECT POWER STATUS /EXIT MENU 1 CURRENT PLAYBACK PROGRAM Beginning of tape End of tape Pro. 1 Pro. 2 Pro.3 Pro. 4 Pro. 5 Pro. 6 Pro.
Helpful Hints If you are having problems with your product, check this list of problems and possible solutions before requesting service. You may be able to solve the problem yourself. If you need to call a customer service representative, please know the model number and serial number of your product before you call. This information is on the back of the product. Also, please take a moment to identify the problem you are having, and be prepared to explain this to the representative.
Helpful Hints (cont’d) 63 The remote control is not available, or the remote control will not access the menu. • Use the buttons on the front of the TV/VCR to access the menu. You can not enter numbers (for example, to program a timer recording) using the front panel buttons. Details are on page 22. TV/VCR has no power. • Connect the power cord to an AC (alternating current) outlet completely. TV/VCR does not have a picture. • Adjust the antenna. Details are on page six.
Glossary AUDIO In Jack: jack on the front of the TV/VCR which records or receives audio from another source. Automatic Channel Setup: process in which the TV/VCR memorizes all available channels. Then, when you push the CHANNEL o/p buttons, you only scan through channels you receive. Bands: settings that allow you to tune channels. • Antenna – VHF (very high frequency; channels 2-13) and UHF (ultra high frequency; channels 14-69). • Cable – all standard channels can be received without a Cable Box.
Specifications 65 General CRT: 13-inch in line gun (CCC134) 19-inch in line gun (CCC194) Television system: NTSC-M Closed caption system: Section 15.119, FCC (Federal Communications Commission) Standard Video Heads: Four heads Tape width: 1/2 inch (12.65 mm) Tape speed SP: 33.35 mm/sec. LP: 16.67 mm/sec. SLP: 11.12 mm/sec.
RENEWED 90 DAY LIMITED WARRANTY
Index 67 a-b repeat play . . . . . . . . .44-45 accessories . . . . . . . . . . . . . . .68 ant(enna) jack . . . . . . . . . . .6, 23 audio jack . . . . . . . . . . .7, 22, 32 automatic playback . . . . . . . . . . . . . . .57 rewind . . . . . . . . . . . . . . . .57 batteries . . . . . . . . . . . . . . . . . .5 blue background . . . . . . . . . . .47 brightness, adjusting . . . . .26-27 cable/dbs button . . . . .20-21, 25 channel above 100 . . . . . . . . . . . . .24 adding . . . . . . . . . . . . . . . .
SUPPLIED ACCESSORIES The following items are supplied with your TV/VCR; they are provided to help you use or set up your TV/VCR. Remote Control 4835 218 37324 Two AA Batteries 4835 138 17012 OPTIONAL ACCESSORIES The following additional items are not provided with your TV/VCR, but they are designed for use with your new TV/VCR. To order these optional accessories, contact us at: Philips Parts & Accessories Marketing Department 401 East Old Andrew Johnson Highway P.O.
SUPPLIED ACCESSORIES The following items are supplied with your TV/VCR; they are provided to help you use or set up your TV/VCR. Remote Control 4835 218 37324 Two AA Batteries 4835 138 17012 OPTIONAL ACCESSORIES The following additional items are not provided with your TV/VCR, but they are designed for use with your new TV/VCR. To order these optional accessories, contact us at: Philips Parts & Accessories Marketing Department 401 East Old Andrew Johnson Highway P.O.
