BT6000 User manual Portable speaker Register your product and get support at www.philips.
Contents 1 Important 2 Your Bluetooth speaker Introduction What's in the box Overview of the speaker 3 Get started Power supply Turn on/off Adjust volume 4 Use Bluetooth devices 2 2 2 3 3 4 4 4 5 Connect a device Play from Bluetooth device Control your phone call Disconnect a device Reconnect a device 5 5 6 6 7 7 5 Listen to an external device 8 6 Specifications 8 7 Troubleshooting General About Bluetooth device 8 Notice Compliance Care of the environment Trademark notice 9 9 10 10 10 1
1 Important Warning •• Never remove the casing of this speaker. •• Never place this speaker on other electrical equipment. •• Keep this speaker away from direct sunlight, naked flames or heat. •• Make sure that you always have easy access to the power cord, plug, or adaptor to disconnect the speaker from the power. • • • • • • • • Make sure that there is enough free space around the speaker for ventilation. After use under humid circumstance, immediately clean the product with a soft dry cloth.
What's in the box Overview of the speaker Check and identify the contents of your package: 2 3 a Quick Start Guide 1 5 4 /PAIRING Enter Bluetooth pairing mode. After Bluetooth connection, respond to an incoming call. • Clear Bluetooth pairing information. • • b NFC • Connect a NFC compatible device through Bluetooth. • • • • Speaker USB cable for charging USB adapter Printed materials c • Charge the built-in battery. d AUDIO IN • Connect an external audio device.
3 Get started Note •• Rechargeable battery has a limited number Always follow the instructions in this chapter in sequence. Power supply Either AC power or the built-in battery can be used as power supply of this product. of charge cycles. Battery life and number of charge cycles vary by use and settings. •• It takes approximately three hours to fully charge the battery. •• The red LED indicator flashes when the battery is low. To recharge the built-in battery: • Connect the speaker to AC power.
To turn the speaker on or off, rotate the knob clockwise or anticlockwise until you hear a click. »» When the speaker is turned on, the blue LED indicator flashes. »» When the speaker is turned off, the blue LED indicator lights off. Note •• If the battery level is low, the red LED indicator flashes. 4 Use Bluetooth devices With this speaker, you can listen to audio from Bluetooth-enabled devices and control the incoming call through Bluetooth.
3 Select [Philips BT6000] displayed on your device for pairing. If necessary, input “0000” as the pairing password. »» After successful connection, the speaker beeps twice, and the LED indicator turns solid blue. • 3 4 Tap the NFC tag on the top of the speaker with the NFC area of your Bluetooth device. Follow the on-screen instructions to complete the pairing and connection. »» After successful connection, the speaker beeps twice, and the LED indicator turns solid blue.
Button /PAIRING Function Press to answer an incoming call. Press and hold for three seconds to reject an incoming call. Clear pairing information Press and hold /PAIRING for 8 seconds. During a call, press to end the current call. During a call, press and hold for three seconds to transfer the call to your mobile device.
5 Listen to an external device 6 Specifications Note •• Product information is subject to change without prior notice. With this speaker, you can also listen to an external audio device such as an MP3 player. Note •• Make sure that music playback through Bluetooth is stopped. 1 2 3 Open the protective cover on the left of the speaker. Connect an audio input cable (not supplied) with a 3.
Standby Power Consumption <1W Eco Standby Power Consumption < 0.5 W Dimensions - Main unit (W x H x D) Weight - Main unit 7 Trouble shooting Warning 188 x 71 x 70 mm 0.5 kg •• Never remove the casing of this device. To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this device, check the following points before requesting service. If the problem remains unsolved, go to the Philips Web page (www.philips.com/support).
The LED indicator is solid red, and the speaker has no response when pressing any key. •• The speaker is in DEMO mode. To exit this mode: after connecting to AC power, press and hold /PAIRING, turn on the speaker, then release the /PAIRING key after 15 seconds. 8 Notice About Bluetooth device Compliance The audio quality is poor after connection with a Bluetooth-enabled device. •• The Bluetooth reception is poor. Move the device closer to this product or remove any obstacle between them.
of with normal household waste. We strongly advise you to take your product to an official collection point or a Philips service centre to have a professional remove the rechargeable battery. Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste.
Copyright © 2016 Gibson Innovations Limited. Revised Edition © 2017 This product has been manufactured by, and is sold under the responsibility of Gibson Innovations Ltd., and Gibson Innovations Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. BT6000MKII_12 _UM_V2.
