BDL6524ET www.philips.
BDL6524ET Safety Instructions Safety precautions and maintenance WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards. Operation: Keep the display out of direct sunlight and away from stoves or any other heat sources. Remove any object that could fall into ventilation holes or prevent proper cooling of the display’s electronics. Do not block the ventilation holes on the cabinet.
BDL6524ET Read and follow these instructions when connecting and using your display: • Unplug the display if you are not going to use it for an extensive period of time. • Unplug the display if you need to clean it with a slightly damp cloth. The screen many be wiped with a dry cloth when the power is off. However, never use alcohol, solvents or ammonia-based liquids. • Consult a service technician if the display does not operate normally when you have followed the instructions in this manual.
BDL6524ET Regulatory Information CE Declaration of Conformity We declare under our responsibility that the product is in conformity with the following standards: • EN60950-1:2006+A11:2009+A1:2010+A12:2011 (Safety requirement of Information Technology Equipment) • EN55022:2010 (Radio Disturbance requirement of Information Technology Equipment) • EN55024:2010 (Immunity requirement of Information Technology Equipment) • EN61000-3-2:2006 +A1:2009+A2:2009 (Limits for Harmonic Current Emission) • EN6100
BDL6524ET Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, display, printer, and so on) should have the same power supply source. The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A).
BDL6524ET Information for U.K. only WARNING – THIS APPLIANCE MUST BE EARTHED. (B) Important: (A) This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place.
BDL6524ET China RoHS 中国电子信息产品污染控制标识要求 (中国RoHS法规标示要求) 产品中有毒有害物质或元素 的名称及含量 有毒有害物质或元素 部件名称 铅 (Pb) 汞 (Hg) 镉 (Cd) 六价铬 (Cr 6+) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) 外壳 O O O O O O 液晶面板 X O O O O O 电路板组件 X O O O O O 附件 (遥控器，电源线，连接线) X O O O O O 遥控器电池 X O O O O O O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下. X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求.
BDL6524ET North Europe (Nordic Countries) Information Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.
BDL6524ET Table Of Contents 1. 2. 3. Unpacking and Installation...................................... 1 1.1. Unpacking......................................................................1 1.2. Package Contents......................................................1 1.3. Installation Notes.......................................................1 1.4. Mounting on a Wall..................................................2 1.5. Mounting in Portrait Position..............................3 1.5.1.
BDL6524ET 1. Unpacking and Installation 1.1. Unpacking • This product is packed in a carton, together with the standard accessories. • Any other optional accessories will be packed separately. • Due to the size and weight of this display it is recommended for two people to move it. • After opening the carton, ensure that the contents are complete and in good condition. 1.2.
BDL6524ET 1.4. Mounting on a Wall To mount this display to a wall, you will have to obtain a standard wall-mounting kit (commercially available). We recommend using a mounting interface that complies with UL1678 standard in North America. Protective Sheet 400 mm 600 mm Table 1. Lay a protective sheet on a table, which was wrapped around the display when it was packaged, beneath the screen surface so as not to scratch the screen face. 2.
BDL6524ET 1.5. Mounting in Portrait Position This display can be installed in portrait position. 1. Remove the table stand, if attached. 2. Rotate 90 degrees clockwise. The “ ” logo should be on the LEFT side when facing the display. 90 90 1.5.1. How to use the logo guider for portrait position 1. Put the guider on the lower-left corner of the front bezel of the display. Fold down both of its edges. 1 2 3 1 2 3 2. Peel off the protective film at the back of the “ ” logo sticker.
BDL6524ET 2. Parts and Functions 2.1. Control Panel 9 MUTE INPUT 1 1 2 3 MENU 4 5 6 7 8 [POWER] button NOTE: “Keyboard Control Lock Mode” This function completely disables the access to all Keyboard Control functions. To enable or disable the keyboard control lock, press both [ ] and [ ] buttons and hold down continuously for more than 3 (three) seconds. Press to turn the display on or put the display to standby. 2 [MUTE] button Press to switch the audio mute ON/OFF.
BDL6524ET 2.2. Input/Output Terminals VIDEO OUT AUDIO OUT AUDIO IN 1 AUDIO IN 3 S-VIDEO IN AUDIO IN 2 VIDEO IN 5 2 7 12 9 13 15 (OUT) 1 3 2 (IN) 1 1 3 4 6 8 10 11 12 AC IN 14 11 AC power input. 2 MAIN POWER SWITCH MAIN POWER SWITCH. 3 AC OUT AC power output. 4 12 RS232C IN / RS232C OUT RJ-45 LAN port connection for your OPS device. 6 13 DVI IN VGA OUT (D-Sub) 14 HDMI IN 15 VGA IN (D-Sub) 16 VIDEO IN (BNC): Composite video signal input.
BDL6524ET 2.3. Remote Control 5 2.3.1. General functions 6 POWER 1 10 SMART VIDEO SOURCE AUDIO SOURCE 2 7 8 12 PIP 9 13 BRIGHTNESS 5 DISPLAY 6 • Press to move the sub-picture left in PIP mode. [SET] button [AUTO ADJUST] button 14 15 10 11 17 AUTO ADJUST EXIT VOL UP MUTE [VIDEO SOURCE] button Press to toggle Video Source Menu. Press [ ] or [ ] button to select one of the video sources among HDMI, DVI-D, VGA, Component, S-Video, Video, or Card OPS.
BDL6524ET 2.3.2. [FREEZE] operation 2.3.5. Operating range of the remote control Press this button to freeze the screen image. Point the top of the remote control toward the display’s remote control sensor when pressing a button. To freeze the screen image: Use the remote control within a distance of less than 10m/33ft from the display’s sensor, and a horizontal and vertical angle of less than 30 degrees. 1. Press the [FREEZE] button on the remote control to activate the FREEZE function. 2.
BDL6524ET 3. Connecting External Equipment 3.1. Using the Switch Cover A cover for the power switch is provided to prevent the display from being turned on or off accidentally. To lock the cover into position: 1. Align and insert the cover to the indentation located beside the power switch. 2. Use the screw to lock the cover.
BDL6524ET 3.2. Connecting External Equipment (DVD/VCR/VCD) 3.2.1. Using COMPONENT video input Component Out (YPbPr) Audio Out DVD / VCR / VCD [AUDIO IN 2], [AUDIO IN 3] [COMPONENT IN] (YPbPr) [R] [L] 3.2.2.
BDL6524ET 3.3. Connecting a PC 3.3.1. Using VGA input VGA Out Audio Out PC [AUDIO IN 1] [AUDIO IN 2], [AUDIO IN 3] [VGA IN] [R] [L] 3.3.2. Using DVI input DVI Out Audio Out PC [AUDIO IN 1] [AUDIO IN 2], [AUDIO IN 3] [DVI IN] [R] [L] 3.3.3.
BDL6524ET 3.4. Connecting Audio Equipment 3.4.1. Connecting external speakers External Speakers Speaker Switch NOTE: Press the [Speaker Switch] to select either the internal or external speakers according to your connection. 3.4.2.
BDL6524ET 3.5. Connecting Multiple Displays in a Daisy-chain Configuration You can interconnect multiple displays to create a daisy-chain configuration for applications such as a video wall. NOTE: Up to maximum 25 displays (5x5) can be used in a daisy-chain configuration. 3.5.1. Control connection [RS-232C] DISPLAY 2 DISPLAY 1 PC [RS232C IN] [RS232C OUT] [RS232C IN] 3.5.2. Video connection [VGA Out] 3.6.
BDL6524ET 3.7. Fixing your external PC Thi sidsplay reserved 6 pcs of M4 screw holes with 100 mm pitch for mounting your Smart Insert Module.
BDL6524ET 3.8. Touch Operation Zoom in This display is equipped with a touch-sensitive screen and supports the Windows Touch features either by singletouch or multitouch operation. You can touch the pictures or words on the display gently with your fingers, and your computer will react. Touch the target on the screen with two fingertips holded together and move them apart to zoom in (magnify) the screen image. The following description illustrate some typical touch operation behavior.
BDL6524ET The Touch screen does not require a device driver be installed on the host computer for all modes of operation. For Windows 7 and Windows 8, it is recommended that the standard Microsoft Window Control Panel calibration is used. Item Description Operating Systems Suppor ted by • Plug-and-Play • Windows 8 Windows 7 (64 bit & 32 bit)1 • Vista (64 bit & 32 bit) • XP (64 bit & 32 bit) • Mac OSX v10.4 and above • Linux 2.
BDL6524ET 4. OSD Menu 4.2. An overall view of the On-Screen Display (OSD) structure is shown below. You can use it as a reference for further adjusting your display. 4.1. OSD Menu Overview 4.2.1. Picture menu Navigating the OSD Menu Picture Contrast Screen 4.1.1.
BDL6524ET NOTE: This item is functional only when {Color temperature} is set to {User}. Clock phase Smart contrast NOTE: This item is functional for VGA input only. When turned on, this function helps enhance image contrast when displaying dark scenes. Zoom mode Adjust to improve the focus, clarity and stability of the image. The pictures you receive may be transmitted in 16:9 format (wide screen) or 4:3 format (conventional screen).
BDL6524ET Audio reset H position Reset all settings in the Audio menu to factory preset values. Moves the horizontal position of the image left or right. Card OPS audio Select the analog or digital audio mode for card OPS. V position Moves the vertical position of the image up or down. 4.2.4. PIP menu PIP Picture PIP input Screen reset Screen Reset all settings in the Screen menu to factory preset values. PIP change PIP size Audio PIP audio 4.2.3.
BDL6524ET By pressing the [PIP ON/OFF] button on the remote control, you can change the mode in the order shown below: PIP PBP aspect POP PBP full Panel saving Choose to enable the panel saving functions and thus reduce the risk of “image persistence” or “ghost-imaging”. Off • {Cooling Fan} – Select {On} to turn on the cooling fan all the time. Select {Auto} to turn on/off the cooling fan according to the display’s temperature.
BDL6524ET • IP address OSD V-position • Subnet mask Adjust the vertical position of the OSD menu. • Default gateway • Login user name (The default user name is {admin}) Monitor information • Login password (The default password is {0000}) Shows information about your display, including model number, serial number, operating hours and software version. Configuration reset Monitor information Reset all settings in Configuration1 menu to the factory preset values.
BDL6524ET NOTE: This item is functional for Video mode input only. Date and time Adjust the current date and time for the display’s internal clock. Scan conversion Choose to enable or disable the IP (Interlace to Progressive) conversion function. • • Date and time {Progressive} – Enable the IP conversion function (recommended). Once enabled, the interlace input signal will be converted to progressive format for better display quality. Year {Interlace} – Disable the IP function.
BDL6524ET 2. Press [ ] or [ ] button to select a schedule item (item number 1 ~ 7), and then press [ ] button to mark it the item number. Some tilting DDC/CI monitors support an auto pivot function, where a rotation sensor in the monitor enables the operating system to keep the display upright as the monitor is moved between its portrait and landscape positions. Schedule The following DDC/CI commands should be supported via command line: Today 1 2 3 4 5 6 7 2013 . 01 .
BDL6524ET Advanced option reset Picture Schecule Action Screen Monitor ID Action Audio DDC/CI On Smart power Off PIP Configuration1 Configuration2 Auto signal detection Off APM Off OPS settings Always on Advanced option reset Action Advanced option Reset all settings in the {Advanced option} menu to factory preset values. 1. Press [SET] or [ ] button to enter the submenu. 2. Press [ ] or [ ] button to select {Reset} and press the [SET] button to restore settings to factory preset values.
BDL6524ET 5. Input Mode PC Resolution: Standard Resolution Active Resolution H Pixels Refresh Rate Pixel Rate 480 60 Hz 25.175 MHz 480 72 Hz 31.5 MHz 480 75 Hz 31.5 MHz 400 70 Hz 33.75 MHz 600 60 Hz 40 MHz 600 75 Hz 49.5 MHz 768 60 Hz 65 MHz 768 75 Hz 78.75 MHz V Lines Aspect Ratio Stand for Mode 4:3 Video Graphic Array 16:9 Wide Video Graphic Array 4:3 Super VGA 4:3 Extended Graphic Array VGA 640 WVGA 720 SVGA 800 XGA 1024 WXGA 1280 768 60 Hz 79.
BDL6524ET 6. Pixel Defect Policy We strive to deliver the highest quality products and use some of the industry’s most advanced manufacturing processes whilst practicing stringent quality control. However, pixel or sub-pixel defects on the PDP / TFT panels used in Plasma- & LCD- displays are sometimes unavoidable.
BDL6524ET 6.4. Dark Dot Defects Black dot defects appear as pixels or sub-pixels that are always dark or “off ”. These are the examples of black dot defects: One dark dot 6.5. Two adjacent dark dots = 1 pair of dark dots Two dark dots, specifications defines the minimum distance between dark dots Proximity of Pixel Defects Because pixel and sub-pixels defects of the same type that are nearby one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects.
BDL6524ET 7. Cleaning and Troubleshooting 7.1. Cleaning Caution When Using the Display • Do not bring your hands, face or objects close to the ventilation holes of the display. The top of the display is usually very hot due to the high temperature of exhaust air being released through the ventilation holes. Burns or personal injuries may occur if any body parts are brought too close.
BDL6524ET 7.2. Troubleshooting Symptom Possible Cause Remedy No picture is displayed 1. The power cord is disconnected. 1. Plug in the power cord. 2. The main power switch on the back of the display is not switched on. 2. Make sure the power switch is switched on. 3. The selected input has no connection. 3. Connect a signal connection to the display. 4. The display is in standby mode.
BDL6524ET 8. Technical Specifications Display: Item Specifications Screen Size (Active Area) 64.5” LCD (163.9 cm) Aspect Ratio 16:9 Number of Pixels 1920 (H) × 1080 (V) Pixel Pitch 0.744 (H) × 0.744 (V) [mm] Displayable Colors 1.
BDL6524ET Environmental Condition: Item Temperature Humidity Altitude Specifications Operational 0 ~ 40°C Storage -20 ~ 60°C Operational 20 ~ 80% RH (No condensation) Storage 10 ~ 90% RH (No condensation) Operational 0 ~ 3,000 m Storage 0 ~ 9,000 m Internal Speaker: Item Specifications Type 1 Way 1 Speaker Input 10 W (RMS) Impedance 8Ω Output Sound Pressure 82 dB/W/M Frequency Response 160 Hz ~ 13 KHz Touch Panel: Technology IR Matrix Touch Method finger and stylus Resolution (p
© 2013 Koninklijke Philips Electronics N.V. All rights reserved. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips Electronics N.V. and are used under license from Koninklijke Philips Electronics N.V. Specifications are subject to change without notice.
