BDL4652EL www.philips.
BDL4652EL Safety Instructions Safety precautions and maintenance WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards. Read and follow these instructions when connecting and using your display: Operation: • Keep the display out of direct sunlight and away from stoves or any other heat sources.
BDL4652EL Read and follow these instructions when connecting and using your display: • Unplug the display if you are not going to use it for an extensive period of time. • Unplug the display if you need to clean it with a slightly damp cloth. The screen many be wiped with a dry cloth when the power is off. However, never use alcohol, solvents or ammonia-based liquids. • Consult a service technician if the display does not operate normally when you have followed the instructions in this manual.
BDL4652EL Regulatory Information CE Declaration of Conformity We declare under our responsibility that the product is in conformity with the following standards: • EN60950-1:2006+A11:2009+A1:2010+A12:2011 (Safety requirement of Information Technology Equipment). • EN55022:2010 (Radio Disturbance requirement of Information Technology Equipment). • EN55024:2010 (Immunity requirement of Information Technology Equipment). • EN61000-3-2:2006 +A1:2009+A2:2009 (Limits for Harmonic Current Emission).
BDL4652EL Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, display, printer, and so on) should have the same power supply source. The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A).
BDL4652EL Information for U.K. only WARNING - THIS APPLIANCE MUST BE EARTHED. (B) Important: (A) This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place.
BDL4652EL China RoHS 中国电子信息产品污染控制标识要求 (中国RoHS法规标示要求) 产品中有毒有害物质或元素 的名称及含量 有毒有害物质或元素 部件名称 铅 (Pb) 汞 (Hg) 镉 (Cd) 六价铬 (Cr 6+) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) 外壳 O O O O O O 液晶面板 X O O O O O 电路板组件 X O O O O O 附件 (遥控器，电源线，连接线) X O O O O O 遥控器电池 X O O O O O O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下. X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求.
BDL4652EL North Europe (Nordic Countries) Information Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.
BDL4652EL Table Of Contents 1. 2. 3. Unpacking and Installation...................................... 1 1.1. Unpacking......................................................................1 1.2. Package Contents......................................................1 1.3. Installation Notes.......................................................1 1.4. Installing and Removing Table Stands (optional)........................................................................2 1.5. Mounting on a Wall............
BDL4652EL 1. Unpacking and Installation 1.1. Unpacking • This product is packed in a carton, together with the standard accessories. • Any other optional accessories will be packed separately. • Due to the size and weight of this display it is recommended for two people to move it. • After opening the carton, ensure that the contents are complete and in good condition. 1.2.
BDL4652EL 1.4. Installing and Removing Table Stands (optional) To install table stands: 1. Ensure your display is powered off. 2. Spread a protective sheet on a flat surface. 3. Grab the carrying handles and place the display face-down on the protective sheet. 4. After inserting the stand in the guide block, tighten the screws on both sides of the display. NOTE: The longer side of the stand should face the front of the display.
BDL4652EL 1.5. Mounting on a Wall To mount this display to a wall, you will have to obtain a standard wall-mounting kit (commercially available). We recommend using a mounting interface that complies with TUV-GS and/or UL1678 standard in North America. Protective Sheet VESA Grid Table Tabletop stand 1. Lay a protective sheet on a table, which was wrapped around the display when it was packaged, beneath the screen surface so as not to scratch the screen face. 2.
BDL4652EL 1.6. Mounting in Portrait Position This display can be installed in portrait position. 1. Remove the table stand, if attached. 2. Rotate 90 degrees clockwise. The “ ” logo should be on the LEFT side when facing the display. 90 90 1.6.1. How to use the logo guider for portrait position 1. Put the guider on the lower-left corner of the front bezel of the display. Fold down both of its edges. 2. Peel off the protective film at the back of the “ ” logo sticker.
BDL4652EL 1.7.
BDL4652EL 1.7.1. Installing Edge Alignment Kit • Before install edge alignment kit, displays must be mounted to video wall frame correctly. • Using “Thumb Screw” for easy installing. • Using “Edge Alignment Kit-1” on adjacent four displays. • 1 2 4 3 Install the “Edge Alignment Kit-1” with 4 PCS of M4 screw.
BDL4652EL • Using “Edge Alignment Kit-2” on adjacent two displays. • Install the “Edge Alignment Kit-2” with 2 PCS of M4 screw.
BDL4652EL 2. Parts and Functions 2.1. Control Panel 9 MUTE INPUT 1 1 2 3 MENU 4 5 6 7 8 NOTE: “Keyboard Control Lock Mode” This function completely disables the access to all Keyboard Control functions. To enable or disable the keyboard control lock, press both [ ] and [ ] buttons and hold down continuously for more than 3 (three) seconds. POWER button Use this button to turn the display on or put the display to standby. 2 MUTE button Switch the audio mute ON/OFF.
BDL4652EL 2.2. Input/Output Terminals 21 20 19 18 17 2 1 1 8 3 4 5 6 7 13 9 10 11 12 AC IN 12 MAIN POWER SWITCH 13 AC OUT 14 IR pass through: 15 AC power input from the wall outlet. 2 16 RS232C OUT 17 RS232C IN 18 RJ-45 19 20 OPS SLOT Slot for installing the optional OPS module. DisplayPort 21 KENSINGTON LOCK Used for security and theft prevention. DVI IN DVI-D video input. 11 SPEAKERS OUT External speakers output. HDMI IN DisplayPort video input.
BDL4652EL 2.3. Remote Control 5 2.3.1. General functions 6 POWER 1 10 SMART VIDEO SOURCE AUDIO SOURCE 2 7 8 12 PIP 9 13 BRIGHTNESS 5 DISPLAY 6 • Press to move the sub-picture left in PIP mode. [SET] button [AUTO ADJUST] button 14 15 10 11 17 AUTO ADJUST EXIT VOL UP MUTE [VIDEO SOURCE] button Press to toggle Video Source Menu. Press [ ] or [ ] button to select one of the video sources among Displayport, DVI-D, VGA, HDMI, Component, Video, or Card OPS.
BDL4652EL 2.3.2. Inserting the batteries in the remote control The remote control is powered by two 1.5V AAA batteries. To install or replace batteries: 1. Press and then slide the cover to open it. 2. Align the batteries according to the (+) and (–) indications inside the battery compartment. 3. Replace the cover. Caution: The incorrect use of batteries can result in leaks or bursting.
BDL4652EL 3. Connecting External Equipment 3.1. Using the Switch Cover A cover for the power switch is provided to prevent the display from being turned on or off accidentally. To lock the cover into position: 1. Align and insert the cover to the indentation located beside the power switch. 2. Use the screw to lock the cover.
BDL4652EL 3.2. Connecting External Equipment (DVD/VCR/VCD) 3.2.1. Using COMPONENT video input Audio Out COMPONENT Out (YPbPr) DVD / VCR / VCD [R] [AUDIO IN] [L] [COMPONENT IN] (YPbPr) 3.2.2. Using Video Source input Audio Out Y/CVBS Out [R] [L] DVD / VCR / VCD [AUDIO IN] [Y/CVBS IN] 3.2.3.
BDL4652EL 3.3. Connecting a PC 3.3.1. Using VGA input VGA Out D-Sub 15 pin PC [R] Audio Out [L] [AUDIO IN] [VGA IN] [VGA AUDIO IN] 3.3.2. Using DVI input DVI Out PC [R] Audio Out [L] [AUDIO IN] [DVI IN] [VGA AUDIO IN] 3.3.3.
BDL4652EL 3.3.4. Using DisplayPort input DisplayPort Out PC [DisplayPort IN] 3.4. Connecting Audio Equipment 3.4.1. Connecting external speakers External speakers 3.4.2.
BDL4652EL 3.5. Connecting Multiple Displays in a Daisy-chain Configuration You can interconnect multiple displays to create a daisy-chain configuration for applications such as a video wall. NOTE: Maximum 25 displays (5x5) can be used in a daisy-chain configuration. 3.5.1. Display control connection Connect the [RS232C OUT] connector of DISPLAY 1 to the [RS232C IN] connector of DISPLAY 2. PC [RS-232C] DISPLAY 1 [RS-232C IN] DISPLAY 2 [RS-232C OUT] [RS-232C IN] 3.5.2.
BDL4652EL 3.5.3. Analog video connection Connect the [DVI OUT / VGA OUT] connector of DISPLAY 1 to the [VGA IN] connector of DISPLAY 2.
BDL4652EL 4. OSD Menu 4.2. An overall view of the On-Screen Display (OSD) structure is shown below. You can use it as a reference for further adjusting your display. 4.1. OSD Menu Overview 4.2.1. Picture menu Navigating the OSD Menu Picture Contrast Screen 4.1.1.
BDL4652EL This item is functional only when {Color temperature} is set to {User}. NOTE: Clock Adjust the width of the image. This item is functional for VGA input only. Smart contrast NOTE: Smart contrast function is to enhance image contrast on darker scenes when activated. The Brightness setting in the Picture menu will be disabled when Smart Contrast is activated. Clock phase Adjust to improve the focus, clarity and stability of the image.
BDL4652EL Audio source V zoom Select the audio input source according to the audio signal source connected to the audio input and HDMI sockets on the display. Expands the vertical size of the image only. H position Moves the horizontal position of the image left or right. V position Moves the vertical position of the image up or down. Screen reset Choose from: {Displayport } / {HDMI} / {Audio1} / {Audio2} / {Card OPS}.
BDL4652EL • The PIP function is available only for certain signal source combinations as shown in the table below. Power save • The availability of the PIP function will also depend on the resolution of the input signal being used. • {RGB} - Select {On} to let the display enter APM mode when no signal is detected from the HDMI Graphic mode, HDMI, DVI-D, or VGA inputs after three successive cycles.
BDL4652EL Network settings OSD turn off Assign {IP address}, {Subnet Mask}, and {Default gateway} for the display. Set the period of time the OSD (on-screen display) menu stays on the screen. The options are: {5 ~ 120} seconds. Network settings Information OSD 0 9 Network host name Set the period of time the information OSD is displayed on the upper right corner of the screen. The information OSD will display when input signal is changed.
BDL4652EL The selected settings will become effective after turning off the power and turning it on again. • {Secondary} - Designate this display as the secondary display. This display can not be operated by the remote control, and will only receive the control signal from the primary display via the RS232C connection. • {Lock All} / {Lock all but Volume} / {Lock all but Power} - Lock the remote control function of this display.
BDL4652EL • V monitors - Select the number of displays on the vertical side. Date and time • Position - Select the position of this display in the screen matrix. Adjust the current date and time for the display’s internal clock. • Frame comp. - Choose to turn the frame compensation function on or off. If selected {Yes}, the display will adjust the image to compensate for the width of the display bezels in order to accurately display the image. Date and time Year Frame comp.
BDL4652EL 2. Press [ ] or [ ] button to select a schedule item (item number 1 ~ 7), and then press [ ] button to mark it the item number. a rotation sensor in the monitor enables the operating system to keep the display upright as the monitor is moved between its portrait and landscape positions. The following DDC/CI commands should be supported via command line: Schedule Today 1 2 3 4 5 6 7 2012 . 08 .
BDL4652EL NOTE: • The primary input signal to display priority, and this item is functional for Primary input signal only. • Auto search is functional for No signal only. If the user set the input source manually, the display is based on the users set priority. APM Power save setting. • {Off} - No signal, direct shutdown. ( Default ) • {On} - No signal, enter into Power Save mode. OPS settings Set the OPS configuration under each power condition.
BDL4652EL 5. Input Mode VGA Resolution: Standard Resolution VGA WVGA SVGA XGA WXGA WXGA SXGA SXGA WXGA WXGA UXGA HD1080 Active Resolution H Pixels V Lines 480 640 72 Hz 75 Hz 720 400 600 800 75 Hz 768 1024 75 Hz 1280 768 1280 800 1280 960 1280 1024 1360 768 1366 768 1600 1200 1920 1080 Refresh Rate Pixel Rate Aspect Ratio Stand for Mode 60 Hz 72 Hz 75 Hz 70 Hz 60 Hz 75 Hz 60 Hz 75 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 25.175 MHz 31.5 MHz 31.5 MHz 33.75 MHz 40 MHz 49.5 MHz 65 MHz 78.
BDL4652EL 6. Pixel Defect Policy We strive to deliver the highest quality products and use some of the industry’s most advanced manufacturing processes whilst practicing stringent quality control. However, pixel or sub-pixel defects on the PDP / TFT panels used in Plasma- & LCD- displays are sometimes unavoidable.
BDL4652EL 6.4. Dark Dot Defects Black dot defects appear as pixels or sub-pixels that are always dark or “off ”. These are the examples of black dot defects: One dark dot 6.5. Two adjacent dark dots = 1 pair of dark dots Two dark dots, specifications defines the minimum distance between dark dots Proximity of Pixel Defects Because pixel and sub-pixels defects of the same type that are nearby one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects.
BDL4652EL 7. Cleaning and Troubleshooting 7.1. Cleaning Caution When Using the Display • Do not bring your hands, face or objects close to the ventilation holes of the display. The top of the display is usually very hot due to the high temperature of exhaust air being released through the ventilation holes. Burns or personal injuries may occur if any body parts are brought too close.
BDL4652EL 7.2. Troubleshooting Symptom Possible Cause Remedy No picture is displayed 1. The power cord is disconnected. 1. Plug in the power cord. 2. The main power switch on the back of the display is not switched on. 2. Make sure the power switch is switched on. 3. The selected input has no connection. 3. Connect a signal connection to the display. 4. The display is in standby mode.
BDL4652EL 8. Technical Specifications Display: Item Specifications Screen Size (Active Area) 46” LCD (116.8 cm) Aspect Ratio 16:9 Number of pixels 1920 (H) x 1080 (V) Pixel pitch 0.17675 (H) x 0.53025 (V) [mm] Displayable colors 1073.
BDL4652EL Weight (Without Stand) 22.0 Kg Gross Weight (Without Stand) 28.
2013 © Koninklijke Philips N.V. All rights reserved. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license from Koninklijke Philips N.V. Specifications are subject to change without notice.
