Specifications

3 - 4
2. To prevent sound interference the bass control
options operate exclusively. You cannot combine
the bass from EQUALIZER with wOOx
4.
GAMESOUND
To adjust the game sound, press GAMESOUND once or more to select your option.
=Display briefly shows
, ,
or
.
Note: GAMESOUND is only available when you
play in GAME
•
AUX source.
How to MUTE the sound 1.
Press MUTE on the remote control to interrupt sound reproduction instantly.
= Playback continues without sound and the
display flashes .
2.
To reactivate sound reproduction you can:
– press MUTE again; – adjust the volume controls; – change to another source.
DIGITAL TUNER (See 3)
Tuning to stations
1.
Press STANDBY ON
y
to on, then press
SOURCE once or more to select TUNER (or press TUNER once on the remote control). = Display: shows briefly followed by
waveband, frequency, and preset station number if already stored.
2.
Press BAND / DISPLAY once or more to select your waveband ( TUNER on the remote control)
3.
Tuning to stations: you can tune to your
stations manually or by automatic search tuning: Press down on
or §
(
5 or 6
on the remote
control ) and release button when the frequency in the display starts running. = The radio automatically tunes to a station of
sufficient reception. Display shows during automatic tuning.
4.
Repeat step 3 if necessary until you find the desired station.
•To tune to a weak station, press
or §
§
§
§
§
(
5 or
6
on the remote control ) briefly and repeatedly
until you have found optimal reception.
To improve radio reception: • For FM, extend, incline and turn the telescopic
antenna. Reduce its length if the signal is too strong.
• For MW, the set uses a built-in antenna. Direct
this antenna by turning the whole set.
Programming tuner stations: You can store up to a total of 30 radio stations in the memory, manually or automatically (Autostore). Autostore Automatic programming will start from preset 1. The set will only program stations which are not in the memory already. 1.
Press ALBUM / PRESET- or + once or more to select the preset number .
2.
Press PROG for 4 seconds or more to activate auto store programming. = Display: is shown and available
stations are programmed in order of waveband FM, followed by MW , preset 1 station will
then be played after all stations are stored automatically.
Manual programming 1.
Tune to your desired station (see Tuning to stations).
2.
Press PROG to activate programming. = Display: program flashes.
3.
Press ALBUM / PRESET- or + once or more to allocate a number from 1 to 30 to this station.
4.
Press PROG again to confirm. = Display shows the preset number, waveband
and the frequency of the preset station.
5.
Repeat the above four steps to store other
stations.
Note : You can erase a preset station by storing
another frequency in its place.
To listen to a preset station Press ALBUM / PRESET- or + once or more until
the desired preset station is displayed.
Programming
track numbers
Program in the stop position to select and store your CD tracks in the desired sequence. If you like, store any
track more than once. Up to 20 tracks can be
stored in the memory. 1.
Press SEARCH
or §
on the set to select your
desired
track number.(on the remote control
¡ or
™
)
MP3-CD mode only: First
press
ALBUM/
PRESET
–
or + once or more to
find your album, then press SEARCH
or §
. (on
the remote control
¡ or ™
)
2.
Press PROG. ™ Display: program and the selected track
number .appears briefly.
™ Display : if no track
selected for programming.
3.
Repeat steps 1-2 to select and store all desired
tracks. ™ Display: if you try to program more
than 20 tracks.
4.
To start playback of your disc program, press
2;.
Note: During normal playback, you can press PROG
to add a current track to your program list.
Reviewing the program In stop position, press and hold down PROG for a while until the display shows all your stored track numbers in sequence.
=Display if no tracks programmed.
Erasing a program You can erase the program by: •pressing
9
twice;
= displayed briefly, and program
disappears.
•pressing STANDBY ON
y
• selecting another sound source • opening the CD door.
GAMESOUND (See 8) PLAYING WITH GAMESOUND:
1.
Press SOURCE once or more on the set to select the GAME
•
AUX function (AUX on the remote control)
=Display scrolls :
2.
Connect your console to the cinches on the front of the set AUDIO IN ( LEFT / RIGHT) and VIDEO IN.
3.
Press GAMESOUND once or more to select your game sound option. =
Display briefly shows , ,
or
.
Connecting other equipment to your system Use the supplied video cable to connect the VIDEO OUT terminal on the back of the set to VIDEO IN on a TV or VCR for viewing or recording.
USB PC LINK Quick Setup Guide PC system requirements
– USB port with Windows 98 SE / ME/ 2000/ XP – Intel Pentium MMXX200 or higher – CD-ROM drive
Installing MusicMatch software 1.
Use the supplied USB cable to connect the set to the USB port on your computer. (See B)
2.
Press SOURCE (USB on the remote control) once or
more to select USB PC LINK.
3.
Turn on your PC then insert the supplied USB PC LINK installer disc in the PC's CD-ROM drive. This application software can also be downloaded from http://www.audio.philips.com.
IMPORTANT!
Please use this customized MusicMatch
software for your USB PC Link application.
Remember to un-install all other MusicMatch
jukebox software first from your PC system (if
available).
DIGITAL TUNER DIGITAL TUNER
MP3-CD / CD PLAYER
GAMESOUND / USB PC LINK
INSTRUCTION FOR USE