Always there to help you Register your product and get support at www.philips.
1 Important Safety Notice 2 Your Wireless Microphone and Bluetooth® Speaker Introduction What’s in the box Overview of the unit 2 2 3 5 5 5 5 3 Get started 7 7 7 7 4 Play 9 Connect power Switch on the Bluetooth® speaker Install/replace microphone batteries Sing along through the wireless microphone Play from a Bluetooth® enabled device Play and charge your iPad through the dock connector directly Play from an external device English Contents 9 10 11 12 5 Product information Specifications 13 1
1 Important Safety This ‘bolt of lightning’ indicates uninsulated material within the device may cause an electrical shock. For the safety of everyone in your household, please do not remove the covering. The ‘exclamation mark’ calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems.
• Install all batteries correctly, + and - as marked on the unit. • Remove batteries when the unit is not used for a long time. • Perchlorate Material-special handling may apply. See www.dtsc.ca.gov/ hazardouswaste/perchlorate. p Apparatus shall not be exposed to dripping or splashing, keep it away from direct sunlight,naked flames or heat. Warning •• Never remove the casing of this apparatus. •• Never lubricate any part of this apparatus. •• Never place this apparatus on other electrical equipment.
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna.
2 Your Wireless Microphone and Bluetooth® Speaker English What’s in the box Check and identify the contents of your package: Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. If you contact Philips, you will be asked for the model and serial number of this apparatus. The model number and serial number are on the back of the apparatus. Write the numbers here: Model No.
Bluetooth® speaker a c b d ef i hg a Power indicator • Indicate the power status. • Turn the unit on/off. b c Bluetooth® indicator • Indicate the Bluetooth® status. d -/+ • Adjust volume. • (Press) pair with a Bluetooth® enabled device that supports A2DP (Advanced Audio Distribution Profile). • (Press and hold) pair with the wireless microphone in case automatic pairing fails.
• To switch the unit to standby mode, press on the top panel. • To switch the unit on from standby mode, press again. Always follow the instructions in this chapter in sequence. Connect power English 3 Get started Tip •• If the speaker stays idle for more than 15 minutes, it switches to standby mode automatically. Caution •• Risk of product damage! Make sure that the power supply voltage corresponds to the voltage printed on the back of the unit.
3 Push back the battery cartridge, then close the battery compartment. Note •• If you are not going to use the microphone for a long time, remove the batteries. •• New batteries installed in the microphone support up to 30 hours of continuous use. •• When the power indicator flashes red, it indicates that the power level is low and you need to replace the batteries.
4 Slide the OFF/ON switch on the wireless microphone to the ON position, then select a song from the app and tap Sing -> RECORD. »» The wireless microphone starts to pair with the Bluetooth® speaker automatically. »» After successful pairing and connection, the Bluetooth® indicator turns solid blue. 5 Find and download a tutorial from StarMaker Karaoke + Auto-Tune®, then tap Sing->RECORD for how to sing along through the wireless microphone and Bluetooth® speaker.
Play from a Bluetooth® enabled device Note •• The effective operation range between the Bluetooth® 7 Use -/+ on the top of the Bluetooth® speaker to adjust volume. Note •• If no prompt pops up on your iPad at step 1, you can go to Settings -> General -> About -> AEA7100 -> Find App for Accessory to install the app. speaker and your Bluetooth® enabled device is approximately 10 meters (30 feet).
Select ‘PHILIPS_AEA7100‘ on your Bluetooth® enabled device (if necessary, input ‘0000’ as the paring password). »» After successful pairing and connection, the Bluetooth® indicator on the speaker turns solid blue and the speaker beeps twice. Play and charge your iPad through the dock connector directly English 3 Compatible iPad This unit supports play and charge of the following iPad models: • New iPad • iPad 2 • iPad Load the iPad • 4 Dock your iPad.
Charge the iPad The docked iPad begins to charge as soon as the unit is connected to AC power. Play from an external device You can also listen to an external audio player through the Bluetooth® speaker. AUDIO-IN 1 Connect a 3.5mm audio cable to: • the AUDIO-IN socket on the back of the Bluetooth® speaker. • the headphone socket on an external audio player. 2 Start music play on the external audio player. 3 Use -/+ on the top of the Bluetooth® speaker to adjust volume.
Note •• Product information is subject to change without prior notice. Dimensions (W x H x D) • Speaker • Microphone Weight • Speaker • Microphone 300 x 162 x 148mm 162 x 333 x 162mm 1.3kg 0.3kg Specifications Amplifier Rated Output Power Signal to Noise Ratio Aux-in Link 2 X 5W RMS >70dB 600 mV RMS, 20 kohm Speakers Speaker Impedance Speaker Driver Sensitivity 4 ohm 70mm full range > 84dB/1m/1W Bluetooth® Bluetooth® version Frequency band Range V2.1 + EDR 2.402-2.
6 Troubleshooting Failed to set up connection between the microphone and speaker • Check whether both the wireless microphone and Bluetooth® speaker are switched on. • Make sure that the wireless microphone and Bluetooth® speaker are within the the effective operation range, that is, approximately 10 meters (30 feet). • Press and hold on the top of the Bluetooth® speaker for more than 10 seconds to set up wireless connection manually. Warning •• Never remove the casing of this device.
Specifications are subject to change without notice © 2012 Koninklijke Philips Electronics N.V. All rights reserved. AEA7100_UM_17_V1.
