Always there to help you Register your product and get support at www.philips.
1 Important Safety Notice 2 Your Wireless Microphone and Bluetooth® Speaker Introduction What's in the box Overview of the unit 3 Get started Connect power Switch on the Bluetooth® speaker Install/replace microphone batteries 4 Play Sing along through the wireless microphone Play from a Bluetooth® enabled device Play and charge your iPad through the dock connector directly Play from an external device English Contents 2 2 3 6 6 6 6 8 8 8 8 10 10 11 12 13 5 Product information Specifications 14 14
1 Important Safety This 'bolt of lightning' indicates uninsulated material within the device may cause an electrical shock. For the safety of everyone in your household, please do not remove the covering. The 'exclamation mark' calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems.
o Battery usage CAUTION – To prevent battery leakage which may result in bodily injury, property damage, or damage to the unit: • Install all batteries correctly, + and - as marked on the unit. • Remove batteries when the unit is not used for a long time. • Perchlorate Material-special handling may apply. See www.dtsc.ca.gov/ hazardouswaste/perchlorate. p Apparatus shall not be exposed to dripping or splashing, keep it away from direct sunlight,naked flames or heat.
operated to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. Installers must ensure that 20cm separation distance will be maintained between the device (excluding its handset) and users. FCC rules This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
English operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPad may affect wireless performance. iPad is a trademark of Apple Inc., registered in the U.S. and other countries. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Philips is under license. Note •• The type plate is located on the back of the unit.
2 Your Wireless Microphone and Bluetooth® Speaker Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. If you contact Philips, you will be asked for the model and serial number of this apparatus. The model number and serial number are on the back of the apparatus. Write the numbers here: Model No. __________________________ Serial No.
Bluetooth® speaker c English a b d ef i hg a Power indicator • Indicate the power status. • Turn the unit on/off. b c Bluetooth® indicator • Indicate the Bluetooth® status. d -/+ • Adjust volume. • (Press) pair with a Bluetooth® enabled device that supports A2DP (Advanced Audio Distribution Profile). • (Press and hold) pair with the wireless microphone in case automatic pairing fails.
3 Get started • To switch the unit to standby mode, press on the top panel. • To switch the unit on from standby mode, press again. Always follow the instructions in this chapter in sequence. Connect power Tip •• If the speaker stays idle for more than 15 minutes, it switches to standby mode automatically. Caution •• Risk of product damage! Make sure that the power supply voltage corresponds to the voltage printed on the back of the unit.
English 3 Push back the battery cartridge, then close the battery compartment. Note •• If you are not going to use the microphone for a long time, remove the batteries. •• New batteries installed in the microphone support up to 25 hours of continuous use. •• When the power indicator flashes red, it indicates that the power level is low and you need to replace the batteries.
4 Play Sing along through the wireless microphone Note •• The effective operation range between the wireless microphone and Bluetooth® speaker is approximately 10 meters (30 feet). 1 Dock your iPad onto the Bluetooth® speaker. »» A prompt pops up on the iPad screen, asking you to install the relevant app. If no prompt pops up on your iPad, you can go to Settings -> General -> About -> AEA7000 -> Find App for Accessory to install the app.
English Play from a Bluetooth® enabled device Note •• The effective operation range between the Bluetooth® 6 7 Select a song from The Voice: On Stage and sing along through the wireless microphone. speaker and your Bluetooth® enabled device is approximately 10 meters (30 feet). •• To pair with a Bluetooth® enabled mobile device, make sure that: no iPad is docked; or you have stopped music play and exited The Voice: On Stage on your docked iPad.
3 Select 'PHILIPS_AEA7000' on your Bluetooth® enabled device and if necessary input '0000' as the paring password. »» After successful pairing and connection, the Bluetooth® indicator on the speaker turns solid blue and the speaker beeps twice. Play and charge your iPad through the dock connector directly Compatible iPad This unit supports play and charge of the following iPad models: • New iPad • iPad 2 • iPad Load the iPad • 4 Dock your iPad. Start music play on your Bluetooth® enabled device.
English Charge the iPad The docked iPad begins to charge as soon as the unit is connected to AC power. Play from an external device You can also listen to an external audio player through the Bluetooth® speaker. AUDIO-IN 1 Connect a 3.5mm audio cable (not supplied) to: • the AUDIO-IN socket on the back of the Bluetooth® speaker. • the headphone socket on an external audio player. 2 Start music play on the external audio player. 3 Use -/+ on the top of the Bluetooth® speaker to adjust volume.
5 Product information Note •• Product information is subject to change without prior notice. Specifications Amplifier Rated Output Power Signal to Noise Ratio Aux-in Link 2 X 5W RMS >70dB 600 mV RMS, 20 kohm Speakers Speaker Impedance Speaker Driver Sensitivity 4 ohm 70mm full range > 84dB/1m/1W Bluetooth® Bluetooth® version Frequency band Range V2.1 + EDR 2.402-2.
Failed to set up connection between the microphone and speaker • Check whether both the wireless microphone and Bluetooth® speaker are switched on. • Make sure that the wireless microphone and Bluetooth® speaker are within the the effective operation range, that is, approximately 10 meters (30 feet). • Press and hold on the top of the Bluetooth® speaker for more than 10 seconds to set up wireless connection manually. Warning •• Never remove the casing of this device.
Specifications are subject to change without notice © 2012 Koninklijke Philips Electronics N.V. All rights reserved. AEA7000_07_UM_EN_V1.
