Register your product and get support at www.philips.
Contents 1 Important 3 2 Your Docking Speaker 4 3 Get started 6 4 Play 7 5 Product information 9 Introduction What's in the box Overview of the main unit Connect power Set time format Adjust display brightness Play from iPod/iPhone Play from Bluetooth device Play from an external audio device Adjust volume Specifications 4 4 5 6 6 6 7 7 8 8 9 6 Troubleshooting 10 7 Notice 11 About Bluetooth device Recycling 10 11 EN 2
1 Important • • • • • • • • • • • • • 3 Read these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
2 Your Docking Speaker Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. If you contact Philips, you will be asked for the model and serial number of this apparatus. The model number and serial number are on the bottom of the apparatus. Write the numbers here: Model No. __________________________ Serial No.
Overview of the main unit a f b e d c h g a b e • • • In iPod/iPhone mode, start or pause play. Adjust display brightness. Set 12 or 24 hour format. c Display panel d Dock for iPod/iPhone 5 EN f • • • Enable or disable Bluetooth function. / Adjust volume. Adjust hour format. g MP3-LINK • Connect an external audio device. h DC IN • Connect power.
3 Get started Always follow the instructions in this chapter in sequence. Connect power Caution •• Risk of product damage! Make sure that the power supply voltage matches the voltage printed on the bottom of the unit. •• Risk of electric shock! When you unplug the AC adaptor, always pull the plug from the socket. Never pull the cord. Set time format 1 2 3 Press and hold for 3 seconds. »» [12H] or [24H] is displayed. Press +/- repeatedly to select 12 or 24 hour format. Press to confirm.
4 Play To remove the iPod/iPhone: Pull the iPod/iPhone out of the dock. Charge the iPod/iPhone When the docking speaker is connected to power, the docked iPod/iPhone begins to charge automatically. Play from iPod/iPhone You can enjoy audio from your iPod/iPhone through this docking speaker. Sync time with iPod/iPhone Compatible iPod/iPhone The docking speaker supports the following iPod and iPhone models: Made for.
5 Play audio on your device. »» Audio streams from your device to the docking speaker. Tip •• When your iPod/iPhone is being charged, you can still listen to audio from the external device. Tip •• If your Bluetooth device has been paired with AD752 before, you just need to find out “AD752” on your Bluetooth menu, then confirm the connection. To disconnect Bluetooth: • Press again; • Deactivate Bluetooth function on your device; or • Move the device beyond the communication range.
5 Product information General information AC Power Note •• Product information is subject to change without prior notice. Specifications Amplifier Total Output Power Signal to Noise Ratio MP3 Link 10 W per channel x 2 > 62 dBA 650 mV RMS Bluetooth Standard Frequency band Range Bluetooth Standard Version 2.1+EDR 2.402~2.480 GHzISM Band 10m (free space) Speaker Speaker Impedance Speaker Driver 9 EN 4 ohm 2 5” Operation Power Consumption Standby Power Consumption Max.
6 Troubleshooting Warning •• Never remove the casing of this device. To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this device, check the following points before requesting service. If the problem remains unsolved, go to the Philips Web page (www. philips.com/support). When you contact Philips, make sure that the device is nearby and the model number and serial number are available.
7 Notice Any changes or modifications made to this device that are not expressly approved by Philips Consumer Lifestyle may void the user’s authority to operate the equipment. “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone respectively, and has been certified by the developer to meet Apple performance standards.
Specifications are subject to change without notice © 2012 Koninklijke Philips Electronics N.V. All rights reserved. AD752_05_UM_V1.
