G41M-P25/G41M-S02 m D T H E R B D R R D MODEL NO.
m s i TOP QUALITY & STABILITY • Most Stable Components with Top Quality OTP Sensor Area Tantalum Core Aluminum Core 5 * ^ • - f t DrMOS II Hl-C CAP (Next-Gen OMOS) SFC (8X Longer Uhdme) Uw (ЭО* Higher Power) Solid CAP 1 (10. Yean IMHone uf.
MS-7592 FCC-B RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a class В digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
COPYRIGHT NOTICE The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice. TRADEMARKS All trademarks are the properties of their respective owners. • MSI® is registered trademark of Micro-Star Int'l Co.,Ltd.
MS-7592 SAFETY INSTRUCTIONS • Always read the safety instructions carefully. • Keep this User Manual for future reference. • Keep this equipment away from humidity. • Lay this equipment on a reliable flat surface before setting it up. • The openings on the enclosure are for air convection hence protects the equipment from overheating. Do not cover the openings. • Make sure the voltage of the power source and adjust properly 110/220V before connecting the equipment to the power inlet.
WEEE STATEMENT ENGLISH To protect the global environment and as an environmentalist, MSI must remind you that... Under the European Union ("EU") Directive on Waste Electrical and Electronic Equipment, Directive 2002/96/EC, which takes effect on August 13, 2005, products of "electrical and electronic equipment" cannot be discarded as municipal waste anymore and manufacturers of covered electronic equipment will be obligated to take back such products at the end of their useful life.
MS-7592 ESPAflOL MSI como empresa comprometida eon la protección del medio ambiente, recomienda: Bajo la directive 2002/96/EC de la Union Europea en materia de desechos y/o equipos electrónicos, con fecha de rigor desde el 13 de agosto de 2005, los productos clasificados como "electricos у equipos electrónicos" no pueden ser depositados en los contenedores habituales de su municipio, los fabricantes de equipos electrónicos, estan obligados a hacerse cargo de dichos productos al termino de su periodo de vid
TORKQE Qevreci ózelligiyle bilinen MSI dunyada ęevreyi korumak ięin hatirlatir: Avrupa Birligi (AB) Kararnamesi Elektrik ve Elektronik Malzeme Atigi, 2002/96/ EC Kararnamesi altinda 13 Agustos 2005 tarihinden itibaren geęerli olmak iizere, elektrikli ve elektronik malzemeler diger atiklar gibi ęópe atilamayacak ve bu elektonik cihazlarin ureticileri, cihazlarin kullanim sOreleri bittikten sonra iiriinleri geri toplamakla yukumlti olacaktir.
MS-7592 TABLE OF CONTENT ENGLISH 9 GETTING STARTED 9 SPECIFICATIONS Ю REAR PANEL 12 HARDWARE SETUP 12 BIOS SETUP 22 tR
ЖвФЛ 119 119 ЯШ 120 W® 122 «Я&Й 122 BIOS Й Й ВФИ ttlTfelC 132 137 I / O A * Л.
MS-7592 ENGLISH GETTING STARTED Thank you for choosing the G41M-P25/ G41M-S02 (MS-7592 v6.x) Micro-ATX mainboard. The G41M-P25/ G41M-S02 is based on Intel* G41 & ICH7flCH7R chipset for optimal system efficiency. Designed to fit the advanced Intel* Core™2 Quad/ Core™2 Duo/ Pentium*/ Celeron* processor in LGA775 package, the G41M-P25/ G41M-S02 delivers a high performance and professional desktop platform solution.
SPECIFICATIONS Processor • Intel® Core™2 Quad/ Core™2 Duo/ Pentium®/ Celeron® processor in LGA775 package • Support 4-pin CPU fan pinheader with fan speed control • Support FMB 05a@95W (For the latest information about CPU, please visit http://www.msi.com/index.
MS-7592 - 1 S/PDIF-Out connector 1 CD-ln connector (optional) 1 front audio connector 1 chassis Intrusion connector 1 parallel connector (optional) 1 serial port connecotr (optiobal) 1 TPM connector - 1 ОС switch (optional) Slots • 1 PCI Express x16 slot • 1 PCI Express x1 slot • 1 PCI slot, supports 3.
REAR PANEL The rear panel provides the following connectors: Keyboard DVI-D Port VGA Port USB Ports MIC SS-Out HARDWARE SETUP This section provides instructions on CPU and memory installation, as well as jumper settings on the mainboard. While doing the installation, be careful in holding the components and follow the installation procedures. CPU & Cooler Installation Procedures for LGA775 When you are installing the CPU, make sure that you install the cooler to prevent overheating.
MS-7592 Follow the steps below to install the CPU & cooler correctly. Wrong installation will cause the damage of your CPU & mainboard. 1. The CPU socket has a plastic cap on it to protect the contact from damage. Before you install the CPU, always cover it to protect the socket pins. 2. Remove the cap from the lever hinge side. 3. The pins of socket reveal. 4. Open the load lever. 5. Lift the load lever up and open the load plate. 6.
Installing Memory Modules 1. The memory module has only one notch on the center and will only fit in the right orientation. 2. Insert the memory module vertically into the DIMM slot. Then push it in until the golden finger on the memory module is deeply inserted in the DIMM slot. The plastic clip at each side of the DIMM slot will automatically close when the memory module is properly seated. You can barely see the golden linger If the memory module Is property Inserted In the DIMM slot 3.
MS-7592 ATX 24-Pln Power Connector JPWR1 This connector allows you to connect an ATX 24-pin power supply. To connect the ATX 24-pin power supply, make sure the plug of the power supply is inserted in the proper orientation and the pins are aligned. Then push down the power supply firmly into the connector. ATX 4-Pln Power Connector JPWR2 This 4-Pin power connector is used to provide power to the CPU.
IDE Connector. IDE1 (optional) This connector supports IDE hard disk drives, optical disk drives and other IDE devices. IMPORTANT If you install two IDE devices on the same cable, you must configure the drives to cable select mode or separately to master / slave mode by setting jumpers. Refer to IDE device documentation supplied by the vendors for jumper setting instructions. Serial ATA Connector. SATA1 - 4 This connector is a high-speed Serial ATA interface port.
MS-7592 S/PDIF-Out Connector SPDOUT1 This connector is used to connect S/PDIF (Sony & Philips Digital Interconnect Format) interface for digital audio transmission. CD-ln Connector JCD1 (optional) This connector is provided for external audio input. Front Panel Connectors: JFP1, JFP2 These connectors are for electrical connection to the front panel switches and LEDs. The JFP1 is compliant with Intel® Front Panel I/O Connectivity Design Guide.
Front Panel Audio Connector JAUD1 This connector allows you to connect the front panel audio and is compliant with Intel® Front Panel I/O Connectivity Design Guide. Front USB Connector JUSB1, JUSB2 This connector, compliant with Intel® I/O Connectivity Design Guide, is ideal for connecting high-speed USB interface peripherals such as USB HDD, digital cam- TPM Module connector JTPM1 This connector connects to a TPM (Trusted Platform Module) module.
MS-7592 Chassis Intrusion Connector JCI1 This connector connects to the chassis intrusion switch cable. If the chassis is opened, the chassis intrusion mechanism will be activated. The system will record this status and show a warning message on the screen. To clear the warning, you must enter the BIOS utility and clear the record. Parallel Port Header JLPT1 (optional) This connector is used to connect an optional parallel port bracket.
Overckx* FSB Switch: OC_SW1 (optional) You can overclock the FSB to increase the processor frequency by changing the switch. Follow the instructions below to set the FSB. ON ON 1 2 3 1 2 3 Default 200-»266 MHz BUB BBB ON BBB 1 2 3 ON ВУУ 1 2 3 200-»333 MHz 266-»333 MHz IMPORTANT ' Make sure that you power off the system before setting the switch. * When overciocking cause system instability or crash during boot, please set the switch to default setting.
MS-7592 PCI Express Slot The PCI Express slot supports the PCI Express interface expansion card. PCI Express x16 slot. PCI Express x1 slot. PCI Slot The PCI slot supports LAN card, SCSI card, USB card, and other add-on cards that comply with PCI specifications. IMPORTANT When adding or removing expansion cards, make sure that you unplug the power supply first.
BIOS SETUP Power on the computer and the system will start POST (Power On Self Test) process. When the message below appears on the screen, press key to enter Setup. Press DEL to enter SETUP If the message disappears before you respond and you still wish to enter Setup, restart the system by turning it OFF and On or pressing the RESET button. You may also restart the system by simultaneously pressing , , and keys. Main Page CUB Setup lit 111 tij C a n r i f M (С) 14IS 2865.
MS-7592 BIOS Setting Password Use this menu to set BIOS setting Password. Cell Menu Use this menu to specify your settings for frequency/voltage control. M-Flash Use this menu to read/ flash the BIOS from USB media device. Load Fail-Safe Defaults Use this menu to load the BIOS default values that are factory settings for system operations. Load Optimized Defaults Use this menu to load factory default settings into the BIOS for stable system performance operations.
CPU Technology Support Press to enter the submenu, that shows the technologies that the installed CPU supported. Intel EIST The Enhanced Intel SpeedStep technology allows you to set the performance level of the microprocessor whether the computer is running on battery or AC power. This field will appear after you installed the CPU which support SpeedStep technology. Adjust CPU FSB Frequency (MHz) This item allows you to adjust the CPU FSB frequency.
MS-7592 fail to retain data. This item applies only when synchronous DRAM is installed in the system. tRAS When the DRAM Timing Mode sets to [Manual], the field is adjustable. This setting determines the time RAS takes to read from and write to a memory cell. tRTP When the DRAM Timing Mode sets to [Manual], the field is adjustable. Time interval between a read and a precharge command. tRFC When the DRAM Timing Mode sets to [Manual], the field is adjustable.
you are plagued by EMI, set to Enabled for EMI reduction. Remember to disable Spread Spectrum if you are overclocking because even a slight jitter can introduce a temporary boost in clock speed which may just cause your overclocked processor to lock up. IMPORTANT * If you do not have any EMI problem, leave the setting at [Disabled] for optimal system stability and performance. But if you are plagued by EMI, select the value of Spread Spectrum for EMI reduction.
M-FLASH SETUP M-Flash funcion allows you to flash BIOS from USB drive/ storage drive (FAT/ FAT32 format only), or allows the system to boot from the BIOS file inside USB drive (FAT/ FAT32 format only). To use M-Flash, first boot/reboot the computer and the system will start POST (Power On Self Test) process. When the message below appears on the screen, press key to enter BIOS.
IMPORTANT * Please refer to the block diagram below about the M-Flash function. i Select BIOS file from the root directory of USB/ Storage drive (FAT/FAT32 format only) in "Load BIOS source file from" field Please check USB drive/ Storage drive/ BIOS file status and reboot the system manually again.
