Register your product and get support at www.philips.
1 Caution 2 2 Important 3 3 Your TV 5 4 Use your TV 7 Safety Control Panel Remote Control Remote control usage Switch TV on or off Switch channels Watch connected devices Adjust TV volume 5 Other uses of the TV Accessing the TV menu Change the picture and sound setup Adjusting setup Use timer Adjusting VGA Setup Playing media from USB devices Updating the TV software Restoring the factory setup 6 Setting up channels Setting up channels automatically Updating channels Setting channels manually
1 Caution 2014© TP Vision Europe B.V. All rights reserved. Specifcations are subject to change without notice. Trademarks are the property of Koninklijke Philips N.V or their respective owners. TP Vision Europe B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. The material in this manual is believed adequate for the intended use of the system.
Read and understand all instructions before you use your TV. If damage is caused by failure to follow instructions, the warranty does not apply. Safety Risk of electric shock or fire! • Never expose the TV to rain or water. Never place liquid containers, such as vases, near the TV. If liquids are spilt on or into the TV, disconnect the TV from the power outlet immediately. Contact Philips Consumer Care to have the TV checked before use.
Risk of swallowing batteries! • The product/remote control may contain a coin-type battery, which can be swallowed. Keep the battery out of reach of children at all times! Risk of overheating! • Never install the TV in a confined space. Always leave a space of at least 4 inches or 10 cm around the TV for ventilation. Ensure curtains or other objects never cover the ventilation slots on the TV. Risk of injury, fire or power cord damage! • Never place the TV or any objects on the power cord.
3 Your TV E n g l i sh Remote Control Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your TV at www.philips.com/welcome. Control Panel 3 2 1 4 5 a Volume-: Without the key menu, the volume-down function is available. b Volume+: Without the key menu, the volume-up function is available.
e (Home) Access or exit from the main menu and return to the previous menu. f INFO Display information about current activity. g (Navigation buttons) Navigate through menus and select items. h OK Confirm an entry or selection. i OPTIONS Access options for channels in the TV mode. j (Back) Return to the previous menu or exit from a certain function , and switch to the previous channel or signal source.
Switch channels E n g l i sh 4 Use your TV This section helps you perform basic TV operations. 3 2 1 Switch TV on or off 5 4 Standby indicator • • • To switch on • Plug in the power plug. » If the standby indicator is red, press (Standby-On) on the remote control. Press CH +/- on the remote control or the lower right part of the TV. Enter a channel number using the numeric buttons on the remote control. Press on the remote control to switch and return to the previous channel.
4 Press to switch to and resume the last watched channel. Watch connected devices Note • Switch on the device before selecting it as an external signal source. Use the Source button 1 2 3 Press SOURCE. » The source list appears. Press to select a device. Press OK to select. » The TV switches to the selected device. Adjust TV volume 3 2 1 4 8 EN 5 To increase or decrease volume • Press VOL +/-at the lower right part of the TV or the Volume Control+/- on the remote control.
Change the picture and sound setup Accessing the TV menu Adjusting the picture setup The menu can help you to set up channels, change the picture and sound setup, and access other functions. 1 2 3 4 5 Press (Home) . »» Display menu screen. Change the picture and sound setup to suit your preferences. You can either use the presets or manually change the setup. 1 2 • Select [Setup].
[Cool]: Bluish white tint. [Normal]: White tint. Users can personalize the white tint inPCmode. • [Warm]: Reddish white tint. [Advanced control]: • [Noise Reduction]: Filters and eliminates signal noise within the image. • [Backlight]: Adjusts the screen brightness (when the backlight brightness is set to a low value, a momentary white flicker may be visible when turning on the unit. This is normal. When [Dynamic Backlight] is turned on, this function will be hidden).
• • • • • • • [Sleep Timer]: Sets the duration the TV remains idle before it automatically enters standby mode. Adjust the time with the sleep button on the remote control. Options: Off/10/20/30/60/90/120/180 minutes. (Does not apply in PC mode). [Power On Status]: Sets the TV’s status when it is connected to an AC power supply. [Time Setup]: Sets the system time. [Freeze Switch]: Sets the channel freeze switch mode.
2 Use timer You can set the timer to switch the TV to standby mode at a set time. 3 4 Tip • Before using the timer, please set the sleep timer. Setting the sleep timer Tip • You can turn the TV off earlier, or reset the sleep timer before the TV switches off. 1 2 3 Press Press ADJUST and select [Setup]. Select [Sleep Timer]. Press You can select a time for the sleep timer to turn the TV off. » The longest time that can be set for the sleep timer is 180 minutes.
• • [V.Position]: Adjusts the vertical position. [Phase]: Adjusts the phase frequency of the VGA signal. [Clock]: Adjusts the clock frequency of the VGA signal. Tip • The VGA menu is only visible when connected to a PC. Viewing photos and playing audio and video files 1 2 3 4 Turn on the TV. Connect the USB storage device to the USB port on the side of the TV. Press (Home). Select [USB] and press OK. » The USB browser will open.
Changing slide show playback setup Watching video When you want to start playing a slide show, press (Home) and select one of the following options, then press OK. • [Pause/Play]: Start or stop playback • [Repeat]: Set the playback mode. • [Shuffle]: Play the slide show in order or at random. • [Duration]: Set the length of time that the slide show is played back. • [Effect]: Set special effects to show during transitions between photos.
E n g l i sh Removing USB storage devices Note • In order to avoid damaging the USB storage device, please follow the steps below. 1 2 Switch out of the USB browser by following the steps in the menu. Wait for approximately five minutes before removing the USB storage device. Updating the TV software Philips constantly strives to improve its products, so we recommend that you update your TV software whenever an update becomes available. Please visit the website at www.philips.
6 Setting up channels This chapter explains how to reconfigure and fine-tune channels. 3 4 5 Select [Start frequency (MHz) / End Frequency (MHz)] and use the number keys to enter the three-digit channel frequencies. Select [Start Search] and press OK. Press (Home) Exit. Skipping channels Setting up channels automatically 1 2 Automatically finds and saves channels. 1 2 3 Press ADJUST. Press Select [TV] > [Channels] > [Channel Scan]. Press OK. »» The TV will automatically start searching for channels.
E n g l i sh Renaming channels You can rename channels. Selecting a channel will display its name. 1 2 3 4 5 6 Press ADJUST. Press Select [TV] > [Channels] > [Channel Edit]. » The [Channel Edit] menu will be displayed. Press Select the channel you wish to rename, then press the OK button. Press Select the channel name, then press the OK button to enter the editing interface. Press Type the new name. Select [Confirm], then OK to finish renaming the channel.
7 TV connections b AV input This chapter explains how to connect devices with different interfaces. Video L Pr L R Note • You can use different connection types to connect devices to the TV. Rear connections a Component signal input Audio and video input from DVD players, game consoles and other analog or digital devices Y / AV Pb R c Antenna/ cable TV Input for an antenna, cable or satellite signal.
d PC inputs (VGA and audio) • The TV speakers will automatically be muted when E n g l i sh headphones are plugged in. b HDMI 1/HDMI 2/ HDMI 3 Digital audio and video input from Blu-ray players and other high definition devices VGA AUDIO e SPDIF Transmit sound to digital audio signal, then connected audio device can play digital audio sound. SPDIF c USB Data input from a USB storage device. USB Side connections a Headphones q Stereo sound output for headphones.
Connecting to a computer AUDIO Before connecting the computer to the TV: • Set the computer screen refresh rate to 60Hz. • Select a supported resolution on the computer. Connect to the computer using one of the following connections: Notes • A separate audio cable is required when connecting with DVI or VGA.
Make full use of your Philips EasyLink HDMICEC-compatible device to improve the control features and obtain the maximum benefit. HDMI-CEC-compatible devices connected with an HDMI connection can be controlled using the TV remote control. If you want to turn Philips EasyLink on, you must: • Connect two or more HDMI-CECcompatible devices using HDMI connections. • Confirm that each HDMI-CEC-compatible device is operating normally. • Switch to EasyLink.
8 Product information Product information is subject to change without notice. For detailed product information, please visit www.philips.com/support. Display resolutions Computer Formats • Resolution - refresh rate: • 640 x 480 - 60Hz • 800 x 600 - 60Hz • 1024 x 768 - 60Hz • 1360 x 768 - 60Hz • 1920 x 1080 - 60Hz Video Formats • Resolution - refresh rate: • 480i - 60Hz • 480p - 60Hz • 576i - 50Hz • 576p - 50Hz • 720p - 50Hz, 60Hz • 1080i - 50Hz, 60Hz • 1080p - 50Hz, 60Hz.
E n g l i sh Warning • Please follow all instructions provided with the TV mount. TP Vision Europe B.V. bears no responsibility for improper TV mounting that results in accident, injury or damage. Model No.
9 Troubleshooting This section covers common problems and their accompanying solutions. General issues The TV cannot be switched on: Disconnect the power cable from the • power outlet. Wait for one minute before reconnecting it. Check that the power cable is securely • connected. The remote control is not working properly: Check that the remote control batteries • are correctly inserted according to the +/orientation. Replace the remote control batteries if they • are flat or weak.
The pictures are showing but sound quality is poor: Note • If no audio signal is detected, the TV automatically switches the audio output off - this does not indicate malfunction. • Check that all cables are properly connected. Check that the volume is not set to 0. • Check that the sound is not muted. • Check that the sound settings are correctly • set. The pictures are showing but sound comes from one speaker only: Verify that sound balance is set to the • centre.
Environmental Protection Use Period This logo labelled on the product itself indicates that the Environmental Protection Use Period thereof is 10 years. The Environmental Protection Use Period of electrical information products refers to the time period during which the toxic and hazardous substances or elements contained within the product will not leak or suddenly spoil, and users of such products will not cause any serious environmental pollution or serious damage to human and property.
© 2014 TP Vision Europe B.V. All rights reserved. Document order number: Philips and the Philips' shield emblem are registered trademarks of Koninklijke Philips N.V. and are used under license from Koninklijke Philips N.V.
